• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.1
• /
• pp.77-82
• /
• 2010

Our study aims to understand the flow of liquid in an open-top rectangular microchannel that can be used in micro total analysis systems ($\mu$-TAS) because it has advantages in terms of light transmission and energy efficiency. We measured the liquid velocity using particle tracking technique and conducted a simulation with computational fluid dynamics by altering the area of channel cross section and channel length for the capillary-driven flow in the open-top rectangular microchannel. When liquid water drops to an entrance of the fabricated microchannel with a height of 20 μm and a width of 20 ${\mu}m$, it flows along the microchannel by only capillary force. In the wetting behavior of the liquid, important parameters of this flow are channel size, contact angle and liquid properties such as surface tension and viscosity, which are used to control the flow of liquid in the microchannel.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.576-583
• /
• 2018

Silicon carbide is considered to be a potentially useful material for high-temperature electronic devices, as its band gap is larger than that of silicon and the p-type and/or n-type conduction can be controlled by impurity doping. Particularly, porous n-type SiC ceramics fabricated from ${\beta}-SiC$ powder have been found to show a high thermoelectric conversion efficiency in the temperature region of $800^{\circ}C$ to $1000^{\circ}C$. For the application of SiC thermoelectric semiconductors, their figure of merit is an essential parameter, and high temperature (above $800^{\circ}C$) electrodes constitute an essential element. Generally, ceramics are not wetted by most conventional braze metals,. but alloying them with reactive additives can change their interfacial chemistries and promote both wetting and bonding. If a liquid is to wet a solid surface, the energy of the liquid-solid interface must be less than that of the solid, in which case there will be a driving force for the liquid to spread over the solid surface and to enter the capillary gaps. Consequently, using Ag with a relatively low melting point, the junction of the porous SiC semiconductor-Ag and/or its alloy-SiC and/or alumina substrate was studied. Ag-20Ti-20Cu filler metal showed promise as the high temperature electrode for SiC semiconductors.

• Journal of Conservation Science
• /
• v.32 no.2
• /
• pp.249-259
• /
• 2016

Effect of the flame retardants on Dancheong is studied in the present work. Two kinds of flame retardants were applied on Dancheong specimens and compared with control groups on which distilled water was applied instead of the flame retardants. The flame retardants enhanced the hygroscopic property of the surface of Dancheong. Furthermore, the added flame retardants reacted with oyster shell white($CaCO_3$) and lead red($Pb_3O_4$), producing new chemical compounds like Calcium phosphate tribasic and Lead Phosphates which make the painted layer of Dancheong dissolving and whitening over certain period of time. When applied in excessive amount and exposed in repetitive wet and dry condition, especially, they aggravate the surface problems significantly. These results will provide a good reference on the study of the discoloring/whitening effect of Dancheong layers at many traditional wooden building in Korea.

• Korean Journal of Materials Research
• /
• v.2 no.3
• /
• pp.180-190
• /
• 1992

Some solutions to several major problems in ZMR such as agglomeration of polysilicon, slips and local substrate melting are described. Experiments are performed with varying polysilicon thickness and capping oxide thickness. The aggmeration can be eliminated when nitrogen is introduced at the capping oxide layer-to-polysilicon interface and polysilicon-to-buried oxide layer interface by annealing the SOI samples at $1100^{\circ}$ in $NH_3$ ambient for three hours. The slips and local substrate melting are removed when the back surface of silicon substrate is sandblasted to produce the back surface roughness of about $20{\mu}m$. The subboundary spacing increases with increasing polysilicon thickness and the uniformity of recrystallized SOI film thickness improves with increasing capping oxide thickness, improving the quality of recrystallized SOI film. When the polysilicon thickness is about $1.0{\mu}m$ and the capping oxide thickness is $2.5{\mu}m$, the thickness variation of the recrystallized SOI film is about ${\pm}200{\AA}$ and the subboundary spacing is about $70-120{\mu}m$.

• Korean Journal of Weed Science
• /
• v.16 no.4
• /
• pp.309-316
• /
• 1996

In this study, germination characteristics and herbicidal response of green kyllinga(Kyllinga brevifolia var. leiolepsis H.) were investigated. The storage method desirable for a rapid dormancy release was to keep the seed under low temp. and wetting condition for one to two months, or high temp($40^{\circ}C$) and drying condition for three months. The dormancy of rhizome was hardly observed. The optimum temperature for germination of seed and rhizome was around $30^{\circ}C$ and 16-$20^{\circ}C$, repectively. The germination of dormancy-breaked seed was completely dependent on light. Shoot emergence ratio(%) was decreased with increase of planting depth ; for example, only 18% of rhizome segments planted in the depth of 4cm under soil surface emerged above soil surface. Flooding at earlier growth stage resulted in significant decrease in shoot emergence as well as in dry weight. The germinablity of rhizome was almost lost as a decreased in fresh weight reached to 50%. Usually, green kyllinga was sensitive to herbicides such as bentazone, bensulfuron and benfuresate etc. which were known to be effective in Cyperaceae weeds, indicating that green kyllinga can be used as a representative plant in the screening of herbicides for Cyperus weeds.

• Applied Biological Chemistry
• /
• v.43 no.2
• /
• pp.116-123
• /
• 2000

A numerical model of three-dimensional soil water distribution for drip irrigation management under cropped conditions was developed using Richards equation in Cartesian coordinates. The model accounts for both seasonal and diurnal changes in evaporation and transpiration, and the growth of plant root and the shape of root zone. Solutions were numerically approximated using the Crank-Nicolson implicit finite difference technique on the block-centered grid system and the Gauss-Seidel elimination in tandem. The model was tested under several conditions to allow the flow rates and configurations of drip emitters vary. In general, simulation results agreed well with experimental results and were as follows. The velocity of soil-water flow decreased drastically with distance from the drip source, and the rate of expansion of the wetted zone decreased rapidly during irrigation. The wetting front of wetted zone from a surface drip emitter traveled farther in vertical direction than in horizontal direction. Under this experimental weather condition, water use efficiency of a drip-irrigated apple field was greatest for 4-drip-emitter system buried at 25 cm, resulting from 10% increase in transpiration but 20% reduction in soil evaporation compared to those for surface 1-drip emitter system. Soil moisture retention curve obtained using disk tension infiltrometer showed significant difference from the curve obtained with pressure plate extractor.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.565-568
• /
• 1998

Amphipathic compounds (bis-sulfonate Gemini type) with double or triple long chain alkyl groups were prepared by the reaction of N-(long chain acyl)diethanolamine diglycidyl ethers with fatty alcohols, followed by the reaction with propanesultone. All these new Gemini type surfactants were soluble in water and showed much better micelle forming ability and lowering surface tension than sodium dodecyl sulfonate with one sulfonate group. cmc and ${\Upsilon}$ cmc values of the triple-chain compounds were still much smaller than those of the corresponding double-chain compounds with two common alkyl groups. The efficiency of adsorption at the water/air interface ($pC_{20}$) of these surfactants was very high. Their foaming properties, wetting ability toward a felt chip, and lime-soap dispersing requirement (LSDR) were measured. Their initial foaming properties were high but showed good low foam stability, wettability and LSDR.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.1
• /
• pp.98-104
• /
• 2014

Photovoltaic (PV) cell is considered as one of the finest ways to utilize the solar power. A study of improving solar cell's efficiency is important because the lifetime of solar cell is determined by photovoltaic module technology. Therefore, oxidation (and/or corrosion) of solder materials will be one of the primary yield and long-term reliability risk factor. Recently, the development of lead-free solder alloy has been done actively about lead-free solder alloys of the thermodynamic and mechanical properties. However, the oxidation behavior have rarely been investigated In this study, the oxidations of 60 wt% Sn-40 wt% Pb, 62 wt% Sn-36 wt% Pb -2 wt% Ag, 50wt% Sn-48 wt% Bi-2 wt% Ag alloys for the interconnect ribbon after exposure in atmosphere at $100^{\circ}C$ for several times were investigated. The wettability of 62 wt% Sn-36 wt% Pb-2 wt% Ag and 50 wt% Sn-48 wt% Bi-2 wt% Ag solders was also studied to compare with that of 60 wt% Sn-40 wt% Pb alloy. The results howed that the zero cross time and the wetting time of 50 wt% Sn-48 wt% Bi-2 wt% Ag solder were better than other two samples. The surface of tested samples was analyzed by XPS. The XPS result showed that in all samples, SnO grew first and then the mixture of SnO and $SnO_2$ was detected. $SnO_2$ grew predominantly for the long time aging. Moreover XPS depth profile analysis has found surface enrichment of tin oxide.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.787-798
• /
• 2017

This is a study on characteristics according to the material of sheet-type mask packs being sold on the market. The absorption capacities of water soluble components such as purified water, 1.3-propanediol, 1.3-butylene glycol, glycerine, and hyaluronic acid are compared with that of various oils including cyclomethicone, dimethicone, phytosqualane, caprylic capryl triglyceride, grape seed oil, and macadamia nut oil. As a result, all of the water soluble components except purified water showed higher moisture absorption capacity as the viscosity increased. And in case of oil, all oil showed higher oil absorption capacity according to the viscosity. During this test, the mask sheets with the type of acetic acid fermented bio-cellulose showed 500~1,000 times or more absorption capacity on water soluble wetting agent or all oils, which is due to the fine mesh structure seen in the 5,000x enlarged photograph at surface structure. This mesh structure was well recognized on the cross section and these structural features enhance the absorption capacity of water and oil. It is also believed that largely contained water-soluble components and oils facilitate the discharge over time. In addition, since each mask sheet shows their characteristics according to their material, it is intended to be a basic research for manufacturing mask packs good for skin.

• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.81-87
• /
• 2011

In this study, UV curing and crosslinking process was introduced for synthesis of acrylic foam tape that can be applied to the the automotive assembly process. Polymerized adhesive are laminated to baseform and varying the thickness of specimens were prepared. To measure basic mechanical properties, stainless steel was used. And in the test peel, dynamic shear and t-block were used. The acrylform adhesive show better results compare with typical adhesive and the properties depand on external factors - thick, wetting time -. To analysis functions of acrylic foam adhesive used to automobile production, evaluate the adhesive properties on the various plastic substrate. In PP and PE are categorized low surface energy materials, their properties have not been expressed. But dynamic shear tests show that some properties could be expressed by the difference break mechanism.