• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.3
• /
• pp.147-152
• /
• 2002

When a liquid is supplied through a nozzle onto a relatively non-wetting inclined solid surface, a narrow rivulet forms. There exist several regimes of rivulet flow depending on various flow conditions. In this paper, the fundamental mechanism behind the transition of a linear rivulet to a droplet flow is investigated. The experiments show that the droplet flow emerges due to the necking of a liquid thread near the nozzle. Based on the observation, it is argued that when the retraction velocity of a liquid thread exceeds its axial velocity, the bifurcation of the liquid thread occurs, and this argument is experimentally verified.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.4
• /
• pp.359-368
• /
• 2014

Photocatalytic cement has been receiving attention due to its high oxidation power that reduces nitrogen oxide, thus contributing to a clean atmospheric environment. However, there has not yet been a thorough investigation on the effect of photocatalytic reactions on the durability of cementitious material, the parent material. In this study, photocatalytic cement samples were exposed to nitric oxide gas and UV along with cycles of wetting and drying to simulate environmental conditions. The surface of samples was characterized mechanically, chemically, and visually during the cycling. The results indicate that that the photocatalytic efficiency decreased with continued NO oxidation. The pits found from SEM indicated that chemical deterioration, such as acid attack or leaching, did occur. However, this was not confirmed by X-ray diffraction. The hardness was not affected, probably due to the formation of CSH as evidenced by the XRD pattern. In conclusion, it was found that photocatalysis could alter cementitious materials both chemically and mechanically, which could further affect long-term durability.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.3
• /
• pp.1-7
• /
• 2011

Active brazing of ceramic to metal is reviewed in this paper. As one of the key aspect in joint techniques, active brazing has been developed to simplify the manufacturing procedure of brazed joints between ceramic and metal. The active filler metal includes Ag-Cu-Ti series, Cu-Ti series, Co-Ti series and so on. The active filler metal which supplies the chemical bonds between ceramic and metal, enhances the wetting of filler metal on ceramic surface and eliminates the need for metallization treatments. The residual stress caused by difference of coefficient of thermal expansion between ceramic and metal, holds a direct influence on the bonding strength and even results in a fracture. Good joints of ceramic to metal promote the miniaturization and simplicity of electronic components with multifunction.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.63-68
• /
• 2003

Scanning electron microscopy (SEM) has been used as a surface measurement instrument and a tool for lithography in semiconductor process due to its high density localized beam. For those purposes, however, the maximum current of SEM Is less than 100pA, which is not enough fo material processing. In this paper SEM was modified to increase the amount of current reaching a specimen from gun part where current is generated, the possibility of applying SEM to material processing, especially microjoining, was investigated. The maximum current of SEM after modifications was measured up to 10$\mu$A, which is about 10$^{5}$ times greater than before modifications. Through experiments such as eutectic solder wetting on thin 304 stainless steel foil and microjoining of 10$\mu$m thick 304 stainless steel, the intensity of electron beam of SEM proved to be great enough fur material processing as heat source. And a tight jig system was found necessary to hold materials close enough fur successful microloining.

• Textile Coloration and Finishing
• /
• v.15 no.4
• /
• pp.51-56
• /
• 2003

Poly(ethylene terephthalate) (PET) fabrics were dyed with a series of ethoxylated alkylaminoanthraquinone dyes synthesized by the reaction of 1-aminoanthraquinone with poly(ethylene glycol) via a series of methylene spacer, and their hydrophilicity and durability to laundering were investigated. The results obtained are as follows: 1) Ethoxylated alkylaminoanthraquinone were successfully exhausted on PET fabric without any aid of chemical auxiliary. 2) The wettability of the dyed PET fabric was increased with the length of ethoxylate chain. 3) The durability of the wettability was good enough as to maintain the initial wettability even after 30 repeated launderings.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.73-79
• /
• 2003

The present study was aimed at analysing the damage of a used gas turbine bucket after 39,500h of total service. Microstructures and cracks of service-induced bucket were observed. The crack might have initiated from the coating in the bucket surface by thermal fatigue and propagated into the GTD111 base metal. Maximum depth of penetration was 2.7 mm(full penetration) at the leading edge. Crack contains a lot of Cr-,Ti-,Al-oxide which will prohibit filling and wetting of insert metal. Depth and propagation direction of crack were accorded with centrifugal force and temperature distribution in turbine bucket. Present result will provide basic data for repair bonding process.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.6-10
• /
• 2008

In this study, the selective-wettability-inscription (SWI) technique for the wet-etchingless fabrication of surface microstructures applicable to wide-viewing liquid crystal displays (LCDs) on plastic substrates was demonstrated. On the basis of the selective wetting of the photopolymer, the bi-level microstructures were spontaneously formed to serve as spacers for maintaining uniform cell gap and protrusions for the generation of multi-domains. The LC cell that has bi-level microstructures shows good extinction in the field-off state and a wide-viewing property in the field-on state. The SWI technique would be useful for the fabrication of flexible displays on plastic substrates.

• Carbon letters
• /
• v.2 no.1
• /
• pp.27-36
• /
• 2001

The pack-cementation process is the method which is formed SiC coating layer to improve weak oxidation properties of CFRCs (carbon fiber-reinforced carbons). This method develops the anti-oxidation coating layer having no dimensional changes and good wetting properties. In this study to improve the oxidative resistance of the prepared 4D CFRCs, the surface of CFRCs is coated by SiC using pack cementation method. The mechanical properties of SiC-coated 4D CFRCs are measured by the 3-point bending test, and their ablation properties are investigated by the arc torch plasma test. From the results, it is found that both mechanical and ablation properties of SiC-coated 4D CFRCs are much better than bare CFRCs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.3
• /
• pp.120-125
• /
• 2002

Si-wafers for solar cells were cast in a size of $50{\times}46{\times}0.5{\textrm}{mm}^3$ by vacuum casting method. The graphite mold coated by BN powder, which was to prevent the reaction of carbon with the molten silicon, was used. Without coating, the wetting and reaction of Si melt to graphite mold was very severe. In the case of BN coating, SiC was formed in the shape of tiny islands at the surface of Si wafer by the reaction between Si-melt and carbon of the graphite mold on the high temperature. The grain size was about 1 mm. The efficiency of Si solar cell was lower than that of Si solar cell fabricated on commercial single and poly crystalline Si wafer. The reason of low efficiency was discussed.

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.429-437
• /
• 1994

Influence of interfacial structure between matrix and particle in A356/coated SiC composite fabricated by squeeze casting method was studied. Experimental variables are types of coated metallic film on SiC particles such as Cu, Ni-P, and applied pressure for squeeze casting. It was found that coating treatment on SiC particles improves the wetting of liquid A356 alloy on SiC particles. SiC particle distribution is very homogeneous in A356 matrix alloy which is fabricated by squeeze casting. Analysing the surface morphology of fractured A356/coated SiC, it was concluded that metallic thin film by coating treatment on SiC particle improves the interfacial bonding between particle and matrix, and so does on mechanical properties such as tensile strength. However, there was on significant difference in hardness between those composite made of as-received SiC particle and coated SiC particle.