• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.146-152
• /
• 2005

The activated carbon was produced from Sancheong bamboo by carbon dioxide gas activation methods. The carbonization of raw material was conducted at $900^{\circ}C$, and $CO_2$ activation reactions were conducted under various conditions: activation temperatures of $750-900^{\circ}C$, flow rates of carbon dioxide $5-30cm^3/g-char{\cdot}min$, and activation time of 2-5 h. The yield, adsorption capacity of iodine and methylene blue, specific surface area and pore size distribution of the prepared activated carbons were measured. The adsorption capacity of iodine (680.8-1450.1 mg/g) and methylene blue (23.5-220 mg/g) increased with increasing activation temperature and activation time. The adsorption capacity of iodine and methylene blue increased with the $CO_2$ gas quantity in the range of $5-18.9cm^3/g-char{\cdot}min$. But those decreased over those range due to the pore shrinkage. The specific volume of the mesopore and macropore of bamboo activated carbon were $0.65-0.91cm^3/g$. Because of this large specific volume, it can be used to the biological activated carbon process. Bamboo activated carbon phisically adsorbed the $CO_2$ of maximum 106 mg/g-A.C in the condition of 90% $CO_2$ and adsorption temperature of $20^{\circ}C$. The $CO_2$ adsorption ability of bamboo activated carbon was not changed in the 5 cyclic test of desorption and adsorption.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.38 no.1
• /
• pp.33-41
• /
• 2011

The objective of this study was to compare the shear bond strengths of five dentin adhesive systems cured with three different light curing sources. Seventy five noncarious permanent teeth were collected and stored in an 0.1% thymol solution at room temperature after extraction. The tested adhesives were: Adper Scotchbond Multi-purpose Plus Adhesive (SM) Adper Single bond 2 (SB), Clearfil SE Bond (SE), Adper Prompt L-Pop (PL), G-Bond (GB). And three light curing unit systems were used: Elipar Free light 2(LED), OptiLux 501 (Halogen), Flipo (PAC). For the shear bonding test, the labial and lingual surfaces of permanent teeth were used. To obtain a flat dentin surface, the labial and lingual surfaces of the teeth were sanded on SiO2 with number 600 grit and then divided into 15 groups of 10 surfaces each. All samples were theromocycled in water $5^{\circ}C$ and $55^{\circ}C$ for 1000 cycles. The results were as follows: 1. When cured with Freelight 2, the shear bond strength of SM was significantly higher than that of PL, GB (p<0.05), whereas no significant difference was found among those of any other bonding agents. 2. When cured with Optilux 501, the shear bond strength of SM was significantly higher than those of any other bonding agents (p<0.05), whereas no singnificant difference was found among those of andy other bonding agents. 3. When cured with Flipo, the shear bond strength of SM was significantly higher than those of SB, SE, GB (p<0.05), whereas no significant differences was found among those of any other bonding agents. 4. For comparison according to three different light cure unit system, except SB and GB, each three dentin bonding agents showed no significant difference. For SB, only Freelight 2 was significantly higher than the others, with no significant difference between Optilux 501 and Flip. For GB, Statistically significant difference was found only between Freelight and Flipo.

• Food Science and Preservation
• /
• v.18 no.5
• /
• pp.661-668
• /
• 2011

This study was conducted to devise appropriate blanching-process conditions as a means to convert Doraji, which is widely used in Korean food due to its unique fragrance and flavor, into frozen food materials for various uses. For the Hunter L values representing the brightness transformation among the surface color and gloss changes that were observed in Doraji before and after freezing, and after Doraji went through a blanching process, the specimen that went through a blanching process at $80^{\circ}C$ showed a significantly higher value compared to another specimen processed at a higher temperature, and the first specimen's value also rose after freezing. Meanwhile, for the hardness values, they declined more as the blanching temperature became higher and as the processing time became longer. For the number of total counts and the number of coliform groups, the number of total counts at $3.75{\times}10^5$ and $1.25{\times}10^5$ cfu/g before the blanching process was reduced into the approximately 2-3 log scale, and no coliform group was detected after the blanching process. As for the peroxidase activity, its activation was decreased by the blanching process, and more than 89% of the peroxidase became inactivated in all the specimens that went through the blanching process. The sensory characteristics of the frozen-thawed Doraji by test group showed the radish leaves blanched at $90^{\circ}C$ for 1 min to be the most highly evaluated in terms of the overall preference level (p<0.05).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.4
• /
• pp.348-355
• /
• 2000

This paper described the relationship between the behavior of the Israeli carp, Cyprinus carpio and the environmental noise level due to the dynamite explosion work. The experiment was conducted in the cage ($L10{\times}W4{\times}D4 m$) of aquaculture located at Chungjoo Lake, Chechon, in 1997. The fish trajectory was obtained by the telemetry system in which a pulsed ultrasonic pinger ($50 kHz, {\phi}16{\times}L70 mm$) attached to the fish was tracked three dimensionally, and the underwater noise levels were measured. The results of the study were as follows: 1. The underwater noise levels in the normal blasting measured at a distance of 400 m from the source of noise increased by $40 dB (re 1 {\mu}Pa)$ compared to the levels before explosion. The dominant frequency and the increased power spectrum level of the underwater noise by the explosion work were $75 to 100 Hz and 22.9 to 35.3 dB$, respectively. 2. The underwater noise levels in the test blasting measured at a distance of 350 m from the source of noise increased by average $49.5 dB (re 1 {\mu}Pa)$compared to the levels before explosion. 3. The swimming area of the fish was reduced with the time after explosion, and after more than one hour the fish represented the similar swimming area and behavior to the status of right before explosion. 4, The swimming depth layer of the fish was most of the case at the sea surface less than 1,0 m except during explosion or right after of it. But the fish swam downward when an external stimulus like the explosion noise was given to the fish. 5. The average swimming speeds of the fish before, during and after the works were about 1.2 times, 1.9 times and 1.0 times of the body length, respectively, and the speed of the fish with explosion was faster 1.6 times than the speed without of that. Consequently, the explosion noise levels measured by this study were sufficiently high to affect the fish, and the heavy shock by the explosion works could produce a considerable unfavorable effects to the fish.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.27-31
• /
• 2000

As the functional test of cornea. The clinical value of keratometric information was important for assessment the curvature of the cornea, the quality of the corneal surface, the stability of the corneal curvature, and the direction of the corneal astigmatism. This study was performed the comparative analysis of male and female of adult on the base curve, power and astigmatism of the Cornea. On the corneal base curve, the male right eye was 7.656 mm in vertical and 7.966 mm in horizontal. But, the male left cornea was 7.714 mm in vertical base curve and 8.026 mm in horizontal base curve. On the other hand, the female right eye cornea was 7.559 mm in vertical base curve and 7.695 mm in horizontal base curve. But, the female left eye cornea was 7.444 mm in vertical base curve and 7.742 mm in horizontal base curve. On the corneal diopter power, the male right eye was 44.063 diopter in vertical and 43.738 diopter in horizontal. But the male left eye was 44.046 diopter in vertical and 42.304 diopter in horizontal. On the other hand, the female right eye was 44.082 diopter in vertical and 43.77 diopter in horizontal. But, the female left eye was 44.347 diopter in vertical and 43.495 diopter in horizontal. According to the corneal astigmatism axis. The male right eye have 89.9% positive for with the - rule astigmatism, and 8.1 % positive for against - the - rule astigmatism. But, he male left eye have 91.89% positive for with - the - rule astigmatism, and 8.11 % positive for against - the - rule astigmatism. On the other hand, The female right eye have 76.92% positive for with - the - rule astigmatism, and 23.08 % positive for against - the - rule astigmatism. But, the female left have 80.76 % positive for with - the - rule astigmatism, and 17.31 % positive for against - the - rule as tigmatism. The diopter power of corneal astigmatism have 25.57% positive for behind 1 diopter, 44.89% positive for 1 diopter, 18.18% positive for 2 diopter, 5.11% positive for 3 diopter and 6.25% positive for over 4 diopter.

• IMMUNE NETWORK
• /
• v.2 no.1
• /
• pp.41-48
• /
• 2002

Background: Viral antigens presented on the cell surface in association with MHC class I molecules are recognized by CD8+ T cells. MHC restricted peptides are important in eliciting cellular immune responses. As peptide antigens have a weak immunigenicity, pH-sensitive liposomes were used for peptide delivery to induce effective cytotoxic T lymphocyte (CTL) responses. In the previous study, as the HBx peptides could induce specific CTLs in vitro, we tested whether the HLA-A2/$K^b$ transgenic mice that were immunized by HBx-derived peptides could be protected from a viral challenge. Methods: HBx-peptides encapsulated by pH-sensitive liposomes were prepared. $A2K^b$ transgenic mice were immunized i.m. on days one and seven with the indicated concentrations of liposome-encapsulated peptides. Three weeks later, mice were infected with $1{\times}10^7pfu$/head of recombinant vaccinia virus (rVV)-HBx via i.p. administration. The ovaries were extracted from the mice, and the presence of rVV-HBx in the ovaries was analyzed using human TK-143B cells. IFN-${\gamma}$ secretion by these cells was directly assessed using a peptide-pulsed target cell stimulation assay with either peptide-pulsed antigen presenting cells (APCs), concanavalin A ($2{\mu}g/ml$), or a vehicle. To generate peptide-specific CTLs, splenocytes obtained from the immunized mice were stimulated with $20{\mu}g/ml$ of each peptide and restimulated with peptide-pulsed APC four times. The cytotoxic activity of the CTLs was assessed by standard $^{51}Cr$-release assay and intracellular IFN-${\gamma}$ assay. Results: Immunization of these peptides as a mixture in pH-sensitive liposomes to transgenic mice induced a good protective effect from a viral challenge by inducing the peptide-specific CD8+ T cells. Mice immunized with $50{\mu}g/head$ were much better protected against viral challenge compared to those immunized with $5{\mu}g$/head, whereas the mice immunized with empty liposomes were not protected at all. After in vitro CTL culture by peptide stimulation, however, specific cytotoxicity was much higher in the CTLs from mice immunized with $5{\mu}g/head$ than $50{\mu}g/head$ group. Increase of the number of cells that intracellular IFN-${\gamma}$ secreting cell among CD8+ T cells showed similar result. Conclusion: Mice immunized with XEPs within pH-sensitive liposome were protected against viral challenge. The protective effect depended on the amount of antigen used during immunization. XEP-3-specific CTLs could be induced by peptide stimulation in vitro from splenocytes obtained from immunized mice. The cytotoxic effect of CTLs was measured by $^{51}Cr$-release assay and the percentage of accumulated intracellular IFN-${\gamma}$ secreting cells after in vitro restimulation was measured by flow cytometric analysis. The result of $^{51}Cr$-release cytotoxicity test was well correlated with that of the flow cytometric analysis. Viral protection was effective in immunized group of $50{\mu}g/head$, while in the in vitro restimulation, it showed more spectific response in $5{\mu}g$/head group.

• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.127-136
• /
• 2015

To evaluate the effects of limestone powder and silica fume on the properties of high-strength high-volume ground granulated blast-furnace slag (GGBFS) blended cement concrete, this study investigated the rheology, strength development, hydration and pozzolanic reaction characteristics, porosity and pore size distribution of high-strength mortars with the water-to-binder ratio of 20, 50 to 80% GGBFS, up to 20% limestone powder, and up to 10% silica fume. According to test results, compared with the Portland cement mixture, the high-volume GGBFS mixture had much higher flow due to the low surface friction of GGBFS particles and higher strength in the early age due to the accelerated cement hydration by increase of free water; however, because of too low water-to-binder ratio and cement content, and lack of calcium hydroxide content, the pozzolanic reactio cannot be activated and the long-term strength development was limited. Limestone powder did not affect the flowability, and also accelerate the early cement hydration. However, because its effect on the acceleration of cement hydration is not greater than that of GGBFS, and it does not have hydraulic reactivity unlikely to GGBFS, compressive strength was reduced proportional to the replacement ratio of limestone powder. Also, silica fume and very fine GGBFS lowered flow and strength by absorbing more free water required for cement hydration. Capillary porosities of GGBFS blended mortars were smaller than that of OPC mortar, but the effect of limestone powder on porosity was not noticeable, and silica fume increased porosity due to low degree of hydration. Nevertheless, it is confirmed that the addition of GGBFS and silica fume increases fine pores.

• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.95-102
• /
• 2015

In this paper, the effects of sodium hydroxide (NaOH) and aluminum potassium sulfate ($AlK(SO_4)_2{\cdot}12H_2O$) dosage on strength properties were investigated. For evaluating the property related to the dosage of alkali activator, sodium hydroxide (NaOH) of 4% (N1 series) and 8% (N2 series) was added to 1~5% (K1~K5) dosage of aluminum potassium sulfate ($AlK(SO_4)_2{\cdot}12H_2O$) and 1% (C1) and 2% (C2) dosage of calcium oxide (CaO). W/B ratio was 0.5 and binder/ fine aggregate ratio was 0.5, respectively. Test result clearly showed that the compressive strength development of alkali-activated slag cement (AASC) mortars were significantly dependent on the dosage of NaOH and $AlK(SO_4)_2{\cdot}12H_2O$. The result of XRD analysis indicated that the main hydration product of $NaOH+AlK (SO_4)_2{\cdot}12H_2O$ activated slag was ettringite and CSH. But at early ages, ettringite and sulfate coated the surface of unhydrated slag grains and inhibited the hydration reaction of slag in high dosage of $NaOH+AlK(SO_4)_2{\cdot}12H_2O$. The $SO_4{^{-2}}$ ions from $AlK(SO_4)_2{\cdot}12H_2O$ reacts with CaO in blast furnace slag or added CaO to form gypsum ($CaSO_4{\cdot}2H_2O$), which reacts with CaO and $Al_2O_3$ to from ettringite in $NaOH+AlK(SO_4)_2{\cdot}12H_2O$ activated slag cement system. Therefore, blast furnace slag can be activated by $NaOH+AlK(SO_4)_2{\cdot}12H_2O$.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.2
• /
• pp.207-220
• /
• 2006

The newly developed equipments for the early detection of carious lesion are LFD (laser fluorescence device), Ultrasonic diagnostic system, CLSM(confocal laser scanning microscopy), QLF(quantitative light-induced fluorescence) and DIFOTI (digital imaging fiber-optic trans-illumination) system. In this study, DIFOTI system and LFD were used for the detection of early enamel caries. Twenty five primary teeth extracted from twenty one children at around the dentitional exchanging period were selected as samples. The results obtained from DIFOTI imaging and LFD measurement were compared with those of CLSM and comprehensive evaluations were made for the diagnostic capacity of each device. In vitro test, 40 sample teeth with their buccal & lingual surface formed by a window of $2{\times}3mm$ in diameter were immersed in artificial demineralizing solution for the period of 4, 8, 12 and 16 days. The results obtained from the experimental groups (DIFOTI, LFD) were compared to control group (CLSM) and we have reached to the following conclusions. 1. The sensitivity and specificity of DIFOTI system operated in oral environment was 88.2% and 76.9% respectively. 2. The sensitivity and specificity of LFD measured in oral environment was 76.5% and 69.2% respectively. 3, Regression analysis on the light transparent rate of DIFOTI showed its decrease according to the length of primary enamel decalcification performed in vitro(r=-0.96, p<0.05). 4. No statistically significant difference between LFT measurement and the length of in vitro decalcification was found in regression analysis (p>0.05). 5. The correlation coefficient of DIFOTI image transparent rate and the lesion depth of CLMS was -0.6988 (p<0.05), whereas no statistically significant difference was found for LFD measurement.

• Journal of The Korean Association For Science Education
• /
• v.33 no.2
• /
• pp.425-443
• /
• 2013

We developed problem-solving type inquiry learning programs reflecting scientists' research process and analyzed the activities of science-gifted high school students, and the understanding and the effects of the programs after implementation in class. For this study, twelve science-gifted students in the 10th grade participated in the program, which consisted of three different modules - making a cycloidal pendulum, surface growth, and synchronization using metronomes. Diet Cola Test (DCT) was used to find out the effect on the improvement of the ability to design experiments by comparing pre/post scores, with a survey and an interview being conducted after the class. Each module consisted of a series of processes such as questioning the phenomenon scientifically, designing experiments to find solutions, and doing activities to solve the problems. These enable students to experience problem-solving type research process through the program class. According to this analysis, most students were likely to understand the characteristics of problem-solving type inquiry learning programs reflecting the scientists' research process. According to the students, there are some differences between this program class and existing school class. The differences are: 'explaining phenomenon scientifically,' 'designing experiments for themselves,' and 'repeating the experiments several times.' During the class students have to think continuously, design several experiments, and carry them out to solve the problems they found at first. Then finally, they were able to solve the problems. While repeating this kind of activities they have been able to experience the scientists' research process. Also, they showed a positive attitude toward the scientists' research by understanding problem-solving type research process. These problem-solving type inquiry learning programs seem to have positive effects on students in designing experiments and offering the opportunity for critical argumentation on the causes of the phenomena. The results of comparing pre/post scores for DCT revealed that almost every student has improved his/her ability to design experiments. Students who were accustomed to following teacher's instructions have had difficulty in designing the experiments for themselves at the beginning of the class, but gradually, they become used to doing it through the class and finally were able to do it systematically.