• Journal of the Korean earth science society
• /
• v.36 no.1
• /
• pp.109-124
• /
• 2015

A novel approach, hybrid surface rainfall (KNU-HSR) technique developed by Kyungpook Natinal University, was utilized for improving the radar rainfall estimation. The KNU-HSR technique estimates radar rainfall at a 2D hybrid surface consistings of the lowest radar bins that is immune to ground clutter contaminations and significant beam blockage. Two HSR techniques, static and dynamic HSRs, were compared and evaluated in this study. Static HSR technique utilizes beam blockage map and ground clutter map to yield the hybrid surface whereas dynamic HSR technique additionally applies quality index map that are derived from the fuzzy logic algorithm for a quality control in real time. The performances of two HSRs were evaluated by correlation coefficient (CORR), total ratio (RATIO), mean bias (BIAS), normalized standard deviation (NSD), and mean relative error (MRE) for ten rain cases. Dynamic HSR (CORR=0.88, BIAS= $-0.24mm\;hr^{-1}$, NSD=0.41, MRE=37.6%) shows better performances than static HSR without correction of reflectivity calibration bias (CORR=0.87, BIAS= $-2.94mm\;hr^{-1}$, NSD=0.76, MRE=58.4%) for all skill scores. Dynamic HSR technique overestimates surface rainfall at near range whereas it underestimates rainfall at far ranges due to the effects of beam broadening and increasing the radar beam height. In terms of NSD and MRE, dynamic HSR shows the best results regardless of the distance from radar. Static HSR significantly overestimates a surface rainfall at weaker rainfall intensity. However, RATIO of dynamic HSR remains almost 1.0 for all ranges of rainfall intensity. After correcting system bias of reflectivity, NSD and MRE of dynamic HSR are improved by about 20 and 15%, respectively.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.237-241
• /
• 1998

The growth orientation and the surface roughness of AIN/Si(111) films grown by radio frequency (RF) reactive magnetron sputtering were investigated using in-situ x-ray scattering technique and atomic force microscopy (AFM). AIN films were initially grown with the <001> preferred growth orientation under most growth conditions. As the film gets thicker, however, the growth orientation changes significantly, especially at high substrate temperature and high RF powers. We attribute the observed behavior to the competition between the surface energy that prefers the <001> growth orientation and the strain energy that randomizes the growth orientation. In addition, we investigated the evolution of the surface morphology during the growth using the x-ray reflectivity measurement.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.1
• /
• pp.25-29
• /
• 2008

We introduce a new fabrication process for antireflective structured surfaces. A 4-inch silicon wafer was dipped in a suspension of 300-nm-diameter silica particles dispersed in a toluene solution. When the wafer was drawn out of the suspension, a hexagonally packed monolayer structure of particles self-assembled on almost the complete wafer surface. Due to the simple process, this could be applied to micro- and nano-patterning. The self-assembled silica particles worked as a mask for the subsequent reactive ion etching. An array of nanometer-sized pits could be fabricated since the regions that correspond to the small gaps between particles were selectively etched off. As etching progressed, the pits became deeper and combined with neighboring pits due to side-etching to produce an array of cone-like structures. We investigated the effect of etching conditions on antireflection properties, and the optimum shape was a nano-cone with height and spacing of 500 nm and 300 nm, respectively. This nano-structured surface was prepared on a $30\;{\times}\;10-mm$ area. The reflectivity of the surface was reduced 97% for wavelengths in the range 400-700 nm.

• Journal of Photoscience
• /
• v.5 no.1
• /
• pp.11-15
• /
• 1998

The texture change of non-linear optical molecules at the air/water interface was investigated as a function of surface pressure with Brewster angle microscopy. The texture change resulted from the aggregation of dye molecules is important to understand the film uniformity and grain formation process. The 4-Octadecylhydroxy-4'-nitrostilbene (OHNS) generated the small spots of size around 1$\mu$m. The spots exhibit high contrast with other film area and do not show angle dependent reflectivity change. It is interesting to observe that the size of the domain stays the same as the film pressure increases. At high surface pressure, the contrast ratio of domains becomes high, which means dense packing of OHNS. And, the size of domain grows. In the middle of domain, highly contrasted domains are formed. The first and the second order transitions of OHNS observed from surface pressure-area isotherm result from the two types of grains. The N,N-Dihexadecylcyanoaniline (DHCA) formed highly contrasted gains over entire region, and the grains are the double layers. The difference in Langmuir film of OHNS and DHCA at the air/water interface is consistent with the small tilt angle from the surface normal for OHNS and the large tilt angle for DHCA in the Langmuir-Blodgett films.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.185-194
• /
• 2016

It is essential for generating the synthetic image to test and evaluate a guided missile system in the hardware-in-the-loop simulation. In order to make the evaluation results to be more reliable, the extent of fidelity and rendering performance of the synthetic image cannot be left ignored. There are numerous challenges to simulate the LWIR sensor signature of sea surface depending on the incident angle, especially in the maritime environment. In this paper, we investigate the key factors in determining the apparent temperature of sea surface and propose the approximate formula consisting of optical characteristics of sea surface and sky radiance. We find that the greater the incident angle increases, the larger the reflectivity of sea surface, and the greater the water vapor concentration in atmosphere increases, the larger the amount of sky radiance. On the basis of this information, we generate the virtual maritime environment in LWIR region using the SE-WORKBENCH, physically based rendering software. The margin of error is under seven percentage points.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.145-152
• /
• 1999

This paper presents the principle and experimental results of a non-contact surface roughness measurement by means of screen projected pattern of lase beam reflected from a polished surface. In the reflected laser beam pattern especially from a fine surface like ground or polished one, light intensity varies from the center fo the image to its boundary as the Gaussian distribution. The standard deviation of a light intensity distribution is assumed to be a good non-contact estimator for measuring the surface roughnes, because the light reflectivity is known to be well related with the surface roughness. This method doesn't need to discriminate between the specularly reflected light and the diffusely reflected one, whereas the scattered laser intensity method must do. Nor it needs to adjust the change of light intensity caused by environmental lights or specimen materials. Reflected laser beam pattern narrowly spreads out in the vertical direction to tiny scratches on the polished surface due to abrasives. The deeper the scratch the more the dispersion, which means the rougher surface. The standard deviation of the pattern is nearly in proportion to the surface roughness. Measurement errors by this method are shown to be below 10 percent compared with those obtained by a common contact method. The inclination of measuring unit from the normal axis causes the measurement errors up to 10 percent for an angle of 4 degree. Therefore the proposed method can be used as an on-the-machine quick roughness estimator within 10 percent measurement error.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.8
• /
• pp.455-460
• /
• 2016

A textured front surface is required in high efficiency silicon solar cells to reduce reflectance and to improve light trapping. Wet etching with alkaline solution is usually applied for mono crystalline silicon solar cells. However, alkali texturing method is not appropriate for multi-crystalline silicon wafers due to grain boundary of random crystallographic orientation. Accordingly, acid texturing method is generally used for multi-crystalline silicon wafers to reduce the surface reflectance. To reduce reflectivity of multi-crystalline silicon wafers, double texturing method with combination of acid and reactive ion etching is an attractive technical solution. In this paper, we have studied to optimize RIE condition by different RF power condition (100, 150, 200, 250, 300 W).

• Journal of the Korean Solar Energy Society
• /
• v.32 no.1
• /
• pp.48-55
• /
• 2012

In recent years, it clearly shows the tendency toward the utilization of daylight in many exhibitory buildings such as museum since the expectation of visitors for whom high illuminance levels are preferable to perceive the details of the works of art. Shading devices and special glazings are often used as the tool to control the amount of light and heat which should be avoided for the presentation of high-light sensitive art works such as paintings. Another way of controling the light is to provide the space for inducing and attenuating light in the exhibitory building. This study aims to investigate the illuminance on the exhibitory space when the space for inducing and attenuating light is applied. Interaction between the daylight and the space was simulated by Lumen Micro program with variation of the size of the exhibitory space, the length of inner wall, surface reflectivity, area of windows to obtain the illumination of the wall surface. This study shows that those variables affect the illumination on the wall surfaces. By comparing the results with suggestive illumination of KS and ICOM, available wall for display on natural lighting are suggested for the seasons and time.

• Korean Journal of Remote Sensing
• /
• v.29 no.1
• /
• pp.81-94
• /
• 2013

The Radar altimeter transmits radio signals to the surface, receives the backscattered signals and measures the distance between the airplane and the nadir surface. The measurements of radar altimeter are affected by various factors on the surface below the aircraft. This study performed flight campaigns in June 2012 and acquired raw data from radar altimeter, LiDAR and other sensors. Based on the LiDAR DSM (Digital Surface Model) as a reference data, the characteristics of radar altimeter were analyzed in the respect of range and surface area affecting on the receiving power of the radar altimeter. Consequently, the radar altimeter was strongly affected by the surface area within beam width and reflectivity related to RCS (Radar Cross Section) rather than range.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.5 no.4
• /
• pp.1-8
• /
• 2002

Comparison between the Tropical Rainfall Measuring Mission(TRMM)/Precipitation Radar(PR) and the C-band doppler radar at Cheju, Kunsan and Pusan, operated by the Korean Meteorological Administration (KMA), is conducted for validation of the surface precipitation structure, and for calibration of KMA radar instrument. Data used in validation was selected for seven rain events in the south region of about $36^{\circ}N$ and at TRMM overflight in Korea, during the summer season of 2000. Quantitatively comparing radar reflectivities from two different platforms that have different view angles, bandwidths and frequencies is a challenging task. For the comparison, the precipitation patterns are projected on the same area for TRMM PR. Through the comparison, it is realized that the reflectivity from ground-based radar is under estimated, compared to TRMM/PR observations. We discuss that is underestimation may be produced by many factors(system performance, topography, etc).