• The Journal of Advanced Prosthodontics
• /
• v.16 no.2
• /
• pp.105-114
• /
• 2024

PURPOSE. This study aimed to evaluate the effect of pretreatment of three different universal adhesives (Single Bond Universal [SBU], All-Bond Universal [ABU], and Prime&Bond universal [PBU]) on the bonding durability of an adhesive (Panavia F 2.0, PF) and a conventional (Duo-Link, DL) resin cements to air-abraded zirconia. MATERIALS AND METHODS. Rectangular-shaped zirconia specimens were prepared. The chemical composition and surface energy parameters of the materials were studied by Fourier transform infrared spectroscopy and contact angle measurement, respectively. To evaluate resin bonding to the zirconia, all the bonding specimens were immersed in water for 24 h and the specimens to be aged were additionally thermocycled 10000 times before the shear bond strength (SBS) test. RESULTS. The materials showed different surface energy parameters, including the degree of hydrophilicity/hydrophobicity. While the DL/CON (no pretreatment) showed the lowest SBS and a significant decrease in the value after thermocycling (P < .001), the PF/CON obtained a higher SBS value than the DL/CON (P < .001) and no decrease even after thermocycling (P = .839). When the universal adhesives were used with DL, their SBS values were higher than the CON (P < .05), but the trend was adhesive-specific. In conjunction with PF, the PF/SBU produced the highest SBS followed by the PF/ABU (P = .002), showing no significant decrease after thermocycling (P > .05). The initial SBS of the PF/PBU was similar to the PF/CON (P = .999), but the value decreased after thermocycling (P < .001). CONCLUSION. The universal adhesive pretreatment did not necessarily show a synergistic effect on the bonding performance of an adhesive resin cement, whereas the pretreatment was beneficial to bond strength and durability of a conventional resin cement.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.57 no.1
• /
• pp.32-40
• /
• 2024

The aim of this research was to apply a method designed to derive the factors influencing total ammonia removal when operating an additional pretreatment system at Aquaponics. The Box-Behnken method, among response surface analysis methods was used to characterize and determine the optimal nitrification conditions when operating the pretreatment system. Among the mathematically and statistically calculated prediction equations, the total ammonia nitrogen concentration Y1 measured on day 8 was derived as Y₁=-195.8+2.23X₁+42.9X₂+47.5X₃+0.1856X₁²-1.380X₁X₂-1.770X₁X₃, and the time taken to reach the maximum total ammonia nitrogen concentration during the experiment period was derived as Y₂=271-5.04X₁+60.5X₂-64.8X₃+0.1654X₁²+6.54X₃²-0.600X₁X₃-9.00X₂X₃. The coefficients of determination of the regression models of Y₁ and Y₂ were 93.99% and 94.46%, respectively. The modified coefficients of determination were also high, at 89.48% and 88.91%, respectively. The prediction coefficients of determination of Y₁ and Y₂, were 70.68% and 62.11%, respectively, which was relatively lower than that of Y1, but still indicated a reliable prediction performance.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.5
• /
• pp.502-513
• /
• 2001

The purpose of this study was to evaluate the effect of dentin pretreatment with Dentin Conditioner, Ultra-Etch, conditioner of Fuji Plus cement on the shear bond strength of resin-reinforced glass ionomer cements to dentin and analyze the fractured surfaces. To evaluate the bond strength, the extracted human teeth which had uniform area of exposed dentin were cemented with conventional glass ionomer cement, 3M $RelyX^{TM}$ Luting (Vitremer luting cement), Fuji Plus cement after dentin pretreatment. The shear bond strength was measured using the Universal testing machine (Instron Co., USA) with a crosshead speed of 1mm/m. The effect of dentin pretreatment was evaluated by observing pretreated dentin surfaces under the scanning electron microscope, measuring the shear bond strength and observing the fractured surfaces under the scanning electron microscope. The results were as follows : On the SEM observation of surface morphology, the specimens treated with Dentin Conditioner. Ultra-Etch and conditioner of Fuji Plus cement were removed the smear layer and funneled dentinal tubules in dentin surfaces. In $RelyX^{TM}$ Luting cement group, shear bond strength of pretreated group was significantly higher than control group. In Fuji Plus cement group and Fuji I group, regardless of the type of pretreatment agents, there was tendency of increase in the shear bond strength. On the SEM observation of fractured surfaces, as the shear bond strength increase, it were shown thicker cement layers and were not shown dentinal tubules According to these results. it were shown that dentin pretreatment have much effect on bonding states.

• Journal of Periodontal and Implant Science
• /
• v.42 no.3
• /
• pp.95-104
• /
• 2012

Purpose: The purpose of this study was to determine whether increasing the Ti6Al4V surface oxide negative charge through heat ($600^{\circ}C$) or radiofrequency plasma glow discharge (RFGD) pretreatment, with or without a subsequent coating with fibronectin, stimulated osteoblast gene marker expression in the MC3T3 osteoprogenitor cell line. Methods: Quantitative real-time polymerase chain reaction was used to measure changes over time in the mRNA levels for osteoblast gene markers, including alkaline phosphatase, bone sialoprotein, collagen type I (${\alpha}1$), osteocalcin, osteopontin and parathyroid hormone-related peptide (PTH-rP), and the osteoblast precursor genes Runx2 and osterix. Results: Osteoprogenitors began to differentiate earlier on disks that were pretreated with heat or RFGD. The pretreatments increased gene marker expression in the absence of a fibronectin coating. However, pretreatments increased osteoblast gene expression for fibronectin-coated disks more than uncoated disks, suggesting a surface oxide-mediated specific enhancement of fibronectin's bioactivity. Heat pretreatment had greater effects on the mRNA expression of genes for PTH-rP, alkaline phosphatase and osteocalcin while RFGD pretreatment had greater effects on osteopontin and bone sialoprotein gene expression. Conclusions: The results suggest that heat and RFGD pretreatments of the Ti6Al4V surface oxide stimulated osteoblast differentiation through an enhancement of (a) coated fibronectin's bioactivity and (b) the bioactivities of other serum or matrix proteins. The quantitative differences in the effects of the two pretreatments on osteoblast gene marker expression may have arisen from the unique physico-chemical characteristics of each resultant oxide surface. Therefore, engineering the Ti6Al4V surface oxide to become more negatively charged can be used to accelerate osteoblast differentiation through fibronectin-dependent and independent mechanisms.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.67-72
• /
• 1999

Optimal pretreatment processes for metal plating on engineering plastics, especially on Nylon-inorganic filler alloy was studied. For Nylon-inorganic filler alloy, adhesion strength between resin surface and metal could be improved by just etching process that eliminate amorphous layer. In the SEM picture and surface roughness measurement, etching treatment was found to make enabled the surface condition very rough and the adhesion strength good. It was also found that the surface condition of plated article and its adhesion strength partly depended upon molding condition of Nylon-inorganic filler alloy. EDS, peaks showed that what kinds of and how much of the metal elements remained on the resin surface after pretreatment processes. Cr did not affect on adsorption of Sn and Pd remarkably.

• Journal of Microbiology and Biotechnology
• /
• v.30 no.8
• /
• pp.1116-1123
• /
• 2020

Velvet antler (VA) is a historically traditional medicinal supplement and is well known in Asian countries for its pharmaceutical and health benefits. The objectives for this study were to optimize the hot water extraction (HWE) of VA for the Korean VA industry, and to determine the most effective pretreatment method among microwave (MW), ultrasonication (US), and enzymatic (EZ) techniques. Using response surface methodology, optimum extraction temperatures and times were determined by central composite design configuration based on extraction yield and sialic acid content. Various quality parameters of VA extract including yield, soluble solid, protein, and sialic acid contents were also compared with the conjunction of HWE and pretreatment. The yield and sialic acid content of VA extract were determined to be 40% and 0.73 mg/g, respectively, under an optimum temperature of 100℃ at 24 h of extraction time. The yields from VA extracts pretreated with MW, US, and EZ were 17.42%, 19.73%, and 29.15%, respectively. Among the tested commercial enzymes, pepsin was the most effective proteolytic enzyme and led to the highest yield (47.65%), soluble solids (4.03 °brix), protein (1.12 mg/ml), and sialic acid (3.04 mg/ml) contents from VA extract.

• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.802-809
• /
• 2001

Electroplating is an attractive alternative deposition method for copper with the need for a conformal and conductive seed layer In addition, the Cu seed layer should be highly pure so as not to compromise the effective resistivity of the filled copper interconnect structure. This seed layer requires low electrical resistivity, low levels of impurities, smooth interface, good adhesion to the barrier metal and low thickness concurrent with coherence for ensuring void-free fill. The electrical conductivity of the surface plays an important role in formation of initial Cu nuclei, Cu nucleation is much easier on the substrate with higher electrical conductivities. It is also known that the nucleation processes of Cu are very sensitive to surface condition. In this study, copper seed layers deposited by magnetron sputtering onto a tantalum nitride barrier layer were used for electroplating copper in the forward pulsed mode. Prior to electroplating a copper film, the Cu seed layer was cleaned by plasma H$_2$ and $N_2$. In the plasma treatment exposure tome was varied from 1 to 20 min and plasma power from 20 to 140W. Effects of plasma pretreatment to Cu seed/Tantalum nitride (TaN)/borophosphosilicate glass (BPSG) samples on electroplating of copper (Cu) films were investigated.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.1
• /
• pp.1-7
• /
• 2024

The study investigated the impact of substrate pretreatment on depositing high-quality B-doped diamond (BDD) thin films using the HFCVD method. Films were deposited on Si and Nb substrates after sanding and seeding. Despite identical sanding conditions, BDD films formed faster on Nb due to even diamond seed distribution. Post-deposition, film average roughness (R_a) remained similar to substrate R_a, but higher substrate R_a led to decreased crystallinity. Nb substrate with 0.83 ㎛ R_a exhibited faster crystal growth due to dense, evenly distributed diamond seeds. BDD film on Nb with 0.83 ㎛ R_a showed a wide, stable potential window (2.8 eV) in CV results and a prominent 1332 cm^-1 diamond peak in R_aman spectroscopy, indicating high quality. The findings underscore the critical role of substrate pretreatment in achieving high-quality BDD film fabrication, crucial for applications demanding robust p-type semiconductors with superior electrical properties.

• The korean journal of orthodontics
• /
• v.3 no.1
• /
• pp.21-28
• /
• 1972

저자는 direct bonding system의 pretreatment액 처리후 Epoxy adhesive의 bonding strength의 변화를 측정하기 위해서 발거된 상악 전치 진면 법랑질 표면에 pretreatment액으로서 $65\%$ phosphoric acid를 도포한 실험군과 도포하지 않은 비교군을 비교연구하고 임상에 적용하여 다음과 같은 결과를 얻었다. 1. 법랑질 표면에 pumicing과 $65\%$ phosphoric acid를 도포했을때 joint strength는 현저히 상승했다. 2. Epoxy adhesive의 bonding strength는 plastic attachment를 치아면에 접착유지시키기에 충분하며 임상적으로 이용할 수 있다. 3. Joint area가 클 수록 bonding strength는 증가했다.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.95-103
• /
• 1992

The purpose of this study was to evaluate the effect of the dentin pretreatment on the marginal leakage of a glassionomer cement. 1n this study, 60 molars with sound and healthy crown portion were used. The dentin surface of these teeth were exposed and polished with 600 grit silicon carbide paper. Square - shaped cavities were prepared on the flattened dentin surfaces and these were divided into 4 groups according to the dentin pretreatment procedures. Group I : Dentin pretreatment with distilled water as a control group. Group II : Dentin pretreatment with 5% sodium hypochlorite solution. Group III : Dentin pretreatment with Ketac conditioner. Group IV : Dentin pretreatment with 40% polyacrylic acid. The degrees of dye penetration in the cavity walls were assessed using a stereoscope at ${\times}40$ magnification according to the maximum dye penetration. The results were analyzed by using Mann - Whitney U test. The results were as follows : 1. All groups showed varying depth of dye penetration. 2. Distilled water group showed the most severe marginal leakage when compared with the other groups(P<0.05). 3. 40% polyacrylic acid group showed the least amount of marginal leakage compared with the other groups (P<0.05). 4. There were significant differences between Goup I(distilled water) and Group IV (40% polyacrylic acid)(P<0.05), but there were no significant differences among Group I(distilled water), Group II(sodium hypochlorite), Group III(Ketac conditioner) (P>0.05).