• Textile Coloration and Finishing
• /
• v.5 no.2
• /
• pp.144-148
• /
• 1993

To increase the moisture content and thereby to reduce the static charge of polyacrylonitrile (PAN), thin layer surface photografting of acylamide (AAm) onto PAN fabrics by using benzophenone as a initiator with a mixtured solvent was carried. The effects of reaction conditions such as monomer, initiator concentrations, UV irradiation time and immersion time of fabrics on grafting were investigated. The percent grafting slightly increased with increasing monomer concentration, benzophenone concentration up to limiting value and thereafter decreased or level offed. The percent grafting was significantly increased with increasing irradiation and immersion times. The moisture regain increased with increasing the percent grafting. The static charge decreased with increasing the percent grafting.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.2
• /
• pp.279-284
• /
• 2016

Assessing the handling properties of coal becomes a major issue for the operation of a fuel supply system in power plants, due to the increased types of coal imported into Korea. In this study, the cohesion strengths of 13 bituminous and sub-bituminous coals from different countries were tested by measuring the amount of force that leads to a failure of consolidated particles. The particle size was in the range of 0.1-2.8 mm, which represents the coarse particles before pulverization. While the cohesion strength was proportional to the compression force in the tested range, the effects of the surface moisture content and the weight fraction of fines were crucial for cohesive coals. At fixed conditions of surface moisture and particle size, large variations were found in the cohesion propensity between coals. For coals of 0.1-0.5 mm with the moisture added close to the critical value, cohesive coals had the density over $900kg/m^3$ after consolidation. The cohesion propensity was not correlated with the basic properties of coals with sufficient statistical significance.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.7-14
• /
• 2006

Three-dimensional distribution and variation of moisture content of boxed-heart square timber of Pinus densiflora was investigated to find the safe and rapid drying methods. As results, microwave-drying method could dry the boxed-heart square timber with sectional dimension of $150{\times}150mm$ under 10% moisture content (MC) within 72 hours with less surface checks, compared with hot-air drying. In case of microwave drying, the MC distribution during drying had a close relation with the initial MC distribution. In case of hot air drying, however, it was independent on the intial one except for the intial drying stage.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.130-136
• /
• 2004

Presence of water in the lubricating oils could be one of the first indicators of potentially expensive and possibly catastrophic failure of the machine as it may cause displace the oil films to prevent the lubrication function of the oil or chemically react with many oil additives resulting in the oil degradation. In order to detect water content quantitatively in lubricating oils many methods and sensors has been developed. Among these, capacitive sensors including sensitive layer, whose dielectric factor changes according to the water content absorbed in the layer, are proposed mainly in the market. But these sensors are not sensitive to a high water content. Besides, the absorbing layer soils in time. In this work, an evaporation of water moisture from oil into air volume above lubricant surface and condensation of water vapor at a cooling surface was used to measure water content quantitatively in an lubricating oil. Laboratory test results of a prototype sensor were presented. Test results showed that the proposed method could be avaliable to measure a low levels of oil moisture.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.283-292
• /
• 1996

This study was performed to determine the physical properties of rice hull and straw which could be used for an optimum design and operation of the handling facilities for these rice crop by-products. The properties measured were kinetic friction coefficient , bulk density, and dynamic and static angle of repose. Rice hulls with moisture content of 13% and 21% were used throughout the test while rice straws of 10% and 16% moisture were chopped into 10mm length and used for the test. Friction coefficient was calculated from the horizontal traction forces measurement when a container holding the mass of rice hull and straw was pulled over mild steel. PVC, stainless steel, and galvanized steel surface by a universal testing machine. Bulk density was measured by an apparatus consisting of filling fundel and a receiving vessel. Dynamic angle of repose which is the angle at which the material will stand when piled was calculated from the photos of bulk samples after they were flowed by gravity and accumulated on a circular surface. Static angle of repose which is the angle between the horizontal and the sloping side of the material left in the container when discharging was also measured in the similar way. Results and conclusions from this study are summarized as follows . 1. Kinetic friction coefficient of both rice hull and straw were in the range of 0.26 -0.52 and increased with the moisture content. The magnitude of friction increased in the order of galvanized steel, stainless steel, PVC ,and mild steel. 2. Bulk densities of rice hull decreased while those of rice straw increased with moisture content increase . Average bulk densities of rice hull and straw were 96.8 and 74.7kg/㎥, respectively. 3. Average dynamic angle of repose for rice straw was 32.6$^{\circ}$ and those for 13% and 21% moisture rice hull were 38.9$^{\circ}$ and 44.9$^{\circ}$ , respectively. 4. Static angles of repose for both rice hull and straw showed increase with the moisture content. The values were 75.2\ulcorner and 80.2$^{\circ}$ for 13% and 21% moisture rice hull, respectively. Rice straws having 10% and 16% moisture content showed 87.3% and 89.2$^{\circ}$ static angle of repose, respectively.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.83-90
• /
• 2008

Permeability to vapor and water among other performances required for finishing materials is dealt with in this study. The relative moisture content of concrete coated/covered with a finishing material was experimentally investigated while changing the environmental conditions including temperature, relative humidity, and rainfall. An organic paint (water-based urethane), organic synthetic resin emulsion-type film coating (film coating E), and inorganic porcelain tiles were selected as the finishing materials. When compared from the aspect of vapor and water permeability, the vapor permeability and water permeability of water-based urethane were high and low, respectively; those of film coating E were high and high, respectively; and those of porcelain tiles were low and low, respectively. This means that the moisture state of concrete structures is governed not only by the environmental conditions but also by the performance of finishing materials. It is therefore of paramount importance to appropriately select a finishing material to address the specific deteriorative factors involved in the concrete structure to be finished.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.3
• /
• pp.29-36
• /
• 2018

In this study, the moisture contents of four Hanoks have been monitored and the results were analyzed. Murujeong and Ongojae were built by traditional construction method and material, and Jeeshinjae and Hwakyeongdang were built by modernized construction method and material. Hwakyeongdang was monitored about 2 years and 9 months and the other three Hanoks were monitored about 4 years and 2 months. The surface moisture contents were measured by the non-destructive electronic resistant type moisture content meter. The measured moisture contents were affected by the orientation to the sun, wood type, temperature and relative humidity. The columns on the northern side and lumber showed more moisture contents than those of the southern side and glue-laminated wood. The moisture contents and relative humidity showed proportional relationship. The moisture contents of all four monitored Hanoks existed proper range by and large.

• Korean Journal of Food Science and Technology
• /
• v.47 no.2
• /
• pp.149-157
• /
• 2015

The effects of feed moisture content (25, 35, and 45%), screw speed (230, 250, and 270 rpm), and barrel temperature (130, 140, and $150^{\circ}C$) on the product yield and soluble arabinoxylan (SAX) content from destarched corn fiber (DCF), and its optimization were investigated. The yield and SAX content of corn fiber gum (CFG) from the extruded destarched corn fiber (EDCF) were higher than those of DCF. Statistical analyses revealed that the feed moisture content and barrel temperature had a significant effect on the CFG yield and total SAX content. The optimum extrusion pretreatment conditions were as follows: feed moisture content, 30%; screw speed, 260 rpm; barrel temperature, $133^{\circ}C$. This study showed that the response surface methodology was suitable for the optimization of the extrusion conditions used to maximize the CFG yield and total SAX content from EDCF.

• Food Science and Preservation
• /
• v.4 no.1
• /
• pp.33-38
• /
• 1997

In order to provide informations for designing packaging and storage condition of dry jujube (Zizyphus jujuba MILLER), moisture sorption isotherm was determined for temperatures of 20, 30 and 4$0^{\circ}C$, and quality changes were evaluated as function of temperature and water activity. Dry jujube at a given water activity showed higher equilibrium moisture content for lower temperature. Moisture isothem could be fitted by GAB model equation, giving higher C value, lower m0 and relatively constant k value with increase in temperature. Ascorbic acid was lost more highly at higher temperature and water activity, and showed negligible retention for whole range of water activity and temperature studied after 141 days. Browning increased with water activity up to 0.73 at 30 and 4$0^{\circ}C$. Dry jujube of high water activity had high L value in surface color, which represent brightness of surface color. Considering quality retention in the storage, dry jujube is desired to be dried to water activity of 0.42 and be stored at temperature below 3$0^{\circ}C$

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.4
• /
• pp.1-8
• /
• 2007

Japanese larch specimens with dimension of 2.5 (radial direction) ${\times}$ 2.5 (tangential direction) ${\times}$ 2.5 cm (longitudinal direction) were prepared to determine 3 different directional internal moisture movement coefficients and surface emission coefficients along the radial-, the tangential-, and the tangential-direction. 4 sides of each cubic specimen were wrapped with paraffin tape and rubber tape, leaving open the 2 opposite surfaces of interest, to provide one dimensional moisture movement during drying. The coefficients were determined at three different temperatures, 70, 50 and $30^{\circ}C$ and at two different relative humidities, 30 and 60%. Internal moisture movement coefficients inclusive of flow of free water and diffusion of bound water and water vapor were increased in the high temperature condition. The internal moisture movement coefficient in the longitudinal direction was about six times of those in transverse directions with radial value being 20% greater than the tangential. Surface emission coefficients were increased with temperature and decreased with surface moisture content. Using this results, moisture content (MC) profile and quantities of moisture evaporating in Japanese larch lumber could be predicted in dynamic drying situations.