• 한국식품조리과학회지
• /
• 제29권5호
• /
• pp.591-598
• /
• 2013

This study was investigated quality properties of Sulgi with different mixed ratio of brown rice flour (BRF) and germinated brown rice flour (GBRF) by rheometer and sensory evaluation. Moisture contents of Sulgi with different mixed ratio of BRF and GBRF were 44.3~46.0%. In textural properties of Sulgi by rheometer, the higher BRF mixed level, hardness of those were higher. The higher GBRF mixed level, springiness, cohesiveness and gumminess of those were higher. In sensory evaluation properties of Sulgi, the higher BRF mixed level, flavor, firmness and graininess of those were higher. The higher GBRF mixed level, surface color, off-flavor, adhesiveness and cohesiveness of those were higher. Correlation between textural properties and sensory evaluation properties, hardness and firmness, graininess, cohesiveness and moistness, gumminess and surface color, gumminess and off-flavor, were correlated positively(p<0.01). Hardness and surface color, hardness and cohesiveness, hardness and overall quality, springiness and firmness, springiness and graininess were correlated negatively (p<0.01).

• 한국재료학회지
• /
• 제13권9호
• /
• pp.606-612
• /
• 2003

Surface and mechanical properties of thin films with submicron thickness was characterized by nanoindentation with Berkovich and Vickers tips, and scanning probe microscopy. Nanoindention was made in a depth range of 15 to 200 nm from the surface by applying tiny force in a range from 150 to $9,000 \mu$N. Stiffness, contact area, hardness, and elastic modulus were determined from the force-displacement curve obtained. Reliability was first tested by using fused quartz, a standard sample. Elastic modulus and hardness values of fused quartz measured were the same as those reported in the literature within two percent of error. Mechanical properties of ITO thin film were characterized in a depth range of 15∼200nm. As indentation depth increased, elastic modulus and hardness decreased by substrate effect. Ion beam deposited DLC thin films were indented in a depth range of 40∼50 nm. The results showed that the DLC thin film using benzene and bias voltage 0∼-50 V has elastic modulus and hardness value of 132 and 18 GPa respectively. Pure DLC thin films showed roughnesses lower than 0.25 nm, but silicon-added DLC thin films showed much higher roughness values, and the wavy surface morphology.

• Journal of Welding and Joining
• /
• 제14권4호
• /
• pp.53-61
• /
• 1996

It was attempted to improve the wear resistance of Al alloy under the load condition by making a formation of the thicker surface hardening alloy layers. The thicker surface hardening alloy layers were formed on 6061 Al alloys overlayed by MIG and TIG welding process with Cu powders feeding. The characteristics of hardening and wear resistance have been investigated in relation to the microstructures of alloyed layers, with a selection of optimum alloying conditions for formation of overlaying layer. The results obtained were summarized as follows With increasing feeding rate of Cu powders by MIG welding, the hardness and specific wear of the overlay weld alloys were increased. It is considered that these high hardness and specific wear of overlay weld alloys were due to the formation of Θ($Al_2Cu$) phases. With increasing feeding rate of Cu powders by TIG welding, the hardness and specific wear of the overlay weld alloys were increased in feeding rates 12 and 18g/min. However, the hardness and specific wear were decreased in the powder feeding rate 38g/min. It is considered that considered that decrease of hardness and specific wear in the powder feeding rate 38g/min due to formation of ${\gamma}$($Al_4Cu_9$) phases.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.427-432
• /
• 1995

Surface heat treatment using a laser beam or an electron beam is studied through numerical analyses and experiments. For the surface heat treatment process, a theoretical model is developed to predict the effects of laser beam power, travel speed and properties of a workpiece on the depth and width of the heat affected zone(HAZ). The shape of HAZ and the hardness of heat-treated surface are experimentally obtained using an electron beam. Three materials(SS41, S45C and S55C) are selected as workpiece materials. The hardness of HAZ is increased up to 3 times for materials of a low carbon content. The results of the numerical analysis are compared with those of experiments. The comparison shows that the numerical model predicts larger depths and widths.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.282-285
• /
• 2009

Selective laser sintering (SLS) is a fast growing process of rapid production fur metallic based parts. To restore damaged mold surface using SLS, single layer experiments of $20{\mu}m$ Fe-Cr powder was performed under various heat input. Process window of $20{\mu}m$ Fe-Cr powder provided feasible process parameters for the smooth regular surface. To estimate coherence between melted powder and basematal, tendency of hardness distribution has been observed. Hardness of melted zone and remelted zone was diversified from 5GPa to 6.5GPa. It is over 2 times compared of hardness of basemetal. Average surface roughness of each direction on surface of melted powder was measured. Experimental results show that the mold restoring process using SLS can be successfully applied in the mold repair industry.

• 한국분말재료학회지
• /
• 제10권3호
• /
• pp.190-194
• /
• 2003

Thin Ag films deposited onto $SiO_2/Si$ substrates by DC magnetron sputtering and thereafter annealed ,it temperatures 100-50$0^{\circ}C$ are investigated by scanning tunneling and atomic forte microscopy. It is shown that the film surface topography and microstructure are considerably changed as a result of annealing. To provide a quantitative estimation of the surface topography changes of Ag films the surface fractal dimension was calculated. Elasticity and hardness of the films are studied by a nanoindentation technique. The films are found to have value of elastic modulus close to that of bulk silver while their hardness and yield stress are essentially higher.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.116-117
• /
• 2006

Conventional high-speed steels, which are carbide decentralized materials, are used for sliding parts, but they lack sufficient hardness for some applications. Improvement of surface hardness is possible for high-Cr steels through nitriding. However, nitriding P/M parts is not advisable without sealing the porosity before treatment, as they will become brittle. However, it is difficult to seal the pores with steam treatment, because high-Cr steel has a passive film on the surface. Controlling nitriding by decreasing the amount of oxygen on the surface to be nitrided, and grinding to decrease the porosity of the surface, makes it possible to produce a material that has reasonable and sufficient hardness in the required areas.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.179-180
• /
• 2012

Back ferrule is a circular ring shaped metallic object which is used for fastening, joining or reinforcement during the tube fitting as well as to prevent leakage. Therefore, during tube fitting the leading edge of the back ferrule should be sufficiently hard enough to prevent leakage. In our research, we concentrated the improvement of two major factors. Firstly, to improve the surface hardness of the back ferrule made by AISI 316 Stainless Steel. Secondly, the enhancement of corrosion resistance of back ferrule after plasma treatment. Initially, the corrosion resistance and hardness of the back ferrule (both commercial and without treated) was not good enough for tube fitting but after applying plasma treatment with suitable conditions on ferrule, we improved the corrosion resistance and hardness of the back ferrule dramatically.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.87-88
• /
• 2020

The purpose of this study is to explore the possibility of estimating optimum surface finish time of the fresh concrete placed at the job site by applying a surface hardness test meter(Durometer). Tests are carried out by measuring and comparing the Penetration resistance test and hardness test by Durometer. Penetration resistance tester and improved Durometer are similar, but the higher the temperature, the higher the setting time, and the higher the correlation was shown. When the hardness value of the improved Durometer is about 50 HD, it is found that the initial and 80 HD represent the end. It is expected that this will be useful in determining the finish time of the surface at the actual site.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.169-170
• /
• 2020

The purpose of this study is to explore the possibility of estimating optimum surface finish time of the fresh concrete placed at the job site by applying a surface hardness test meter(Durometer). Tests are carried out by measuring and comparing the Penetration resistance test and hardness test by Durometer. Penetration resistance tester and improved Durometer are similar, but the higher the temperature, the higher the setting time, and the higher the correlation was shown. When the hardness value of the improved Durometer is about 50 HD, it is found that the initial and 80 HD represent the end. It is expected that this will be useful in determining the finish time of the surface at the actual site.