• 한국전기전자재료학회논문지
• /
• 제15권8호
• /
• pp.695-701
• /
• 2002

Maxwell displacement current (MDC) measuring technique has been applied on the study of monolayers of fatty acid and polyamic acid mixture. The displacement current was generated from monolayers on the water surface by monolayer compression and expansion. Displacement current was generated when the area per molecule was about 132 $^2$and 115 $^2$just before the initial rise of the surface pressure during the 1st and 2nd mixed monolayer compressions cycle, respectively. Maxwell displacement currents were investigated in connection with mixed monolayer compression cycles. It was found that the maximum of MDC appeared at the molecular area just before the initial rise of surface pressure in compression cycles. Ultra thin film of fatty acid and polyamic acid mixture was prepared on the hydrophilic quartz plate by Langmuir-Blodgett (LB) method. The precursor LB film was heated in a vacuum dry oven at 12$0^{\circ}C$ in order to convert it into the LB film of polyimide. The absorption spectra of LB films were also induced photoisomerization by UV and visible light irradiation.

• 한국산학기술학회논문지
• /
• 제12권10호
• /
• pp.4642-4647
• /
• 2011

평면 변형률 상태에 있는 탄성지반의 해를 변분법을 적용하여 유도하여 보았다. 변분법 적용시 종방향 변위분포 함수는 선형함수를 고려하였다. 탄성지반상에 작용하는 하중조건은 집중하중과 분포하중을 고려하였는데 집중하중 작용시 탄성지반의 종방향 변위분포양상은 하중 작용점에서 멀어질수록 변위가 급격하게 감소하는 양상을 나타내었다. 등분포하중 작용시 지표면 변위는 압축층 두께에 대한 재하폭의 반의 비(B/H)값이 클수록 하중재하부분 아래에서 보다 균등하게 발생하였다. 또한 하중재하부분을 벗어난 영역에서는 B/H 값이 커질수록 하중재하 모서리 부분으로부터 짧은 거리에서 변위가 0에 수렴하였다.

• 한국기계가공학회지
• /
• 제19권2호
• /
• pp.69-74
• /
• 2020

In this study, we proposed a method for surface profiling aspheric lens molds using a precision displacement sensor with a spatial scanning mechanism. The precision displacement sensor is based on the confocal principle using a broadband light source, providing a 10 nm resolution over a 0.3 mm measurable range. The precision of the sensor, depending on surface slope, was evaluated via Allan deviation analysis. We then developed an automatic surface profiling system by measuring the cross-sectional profile of a lens mold. The precision of the sensor at the flat surface was 10 nm at 10 ms averaging time, while 200 ms averaging time was needed for identical precision at the steepest slope at 25 deg. When we compared the measurement result of the lens mold to a commercial surface profiler, we found that the accuracy of the developed system was less than 90 nm (in terms of 3 sigmas of error) between the two results.

• 한국자기학회지
• /
• 제22권5호
• /
• pp.183-187
• /
• 2012

본 논문에서는 수평진동이 있는 용기내 자유표면을 갖는 자성유체에 용기하부로부터 수직자장을 인가시킨 경우 유동을 실험하였다. 실험은 직사각형 및 원통형 용기에 대해 자성유체에 인가된 자기력이 공진주파수, 액면변위에 미치는 영향을 조사하였다. 인가자장의 증가는 최대 공진점 및 액면변위에 영향을 미치고 그 결과 표면파의 진폭과 슬로싱 유동의 변동주기를 변화시킨다.

• Elastomers and Composites
• /
• 제37권3호
• /
• pp.151-158
• /
• 2002

본 연구에서 고려된 elastomeric bushing은 자동차 현가장치에 사용되는 기계요소로서, 바깥쪽의 실린더형 슬리브와 안쪽의 실린더형 축 사이에서 가운데가 완전히 비어있는 실린더의 형태를 가진다. 본 연구에서는 일래스토메릭 부싱에 적용되는 힘과 변형의 관계가 비선형이고 점탄성의 특성을 보이므로, Lianis에 의해 발전되어진 비선형 점탄성 비압축 재료에 대한 구조방정식을 사용하여, 부싱의 축방향 응답에 대한 힘과 변위의 관계를 얻었다. 또한 변위에 의존하는 force relaxation function은 extrapolation method에 의한 ramp displacement control test로부터 완성되고, 이는 step displacement control test로부터 얻게된 결과와 비교하며, 두 결과가 매우 잘 일치됨을 확인하였다.

• Computers and Concrete
• /
• 제4권2호
• /
• pp.135-156
• /
• 2007

Three 3D nonlinear finite-element models are developed to study the behavior of concrete beams and plates with and without external reinforcement by fibre-reinforced plastic (FRP). All three models are formulated based upon the 3D theory of elasticity. The stress model is modified from the element developed by Ramtekkar, et al. (2002) to incorporate material nonlinearity in the formulation. Both transverse stress and displacement components are used as nodal degrees-of-freedom to ensure the continuity of both stress and displacement components between the elements. The displacement model uses only displacement components as nodal degrees-of-freedom. The transition model has both stress and displacement components as nodal degrees-of-freedom on one surface, and only displacement components as nodal degrees-of-freedom on the opposite surface. The transition model serves as a connector between the stress and the displacement models. The developed models are validated by comparing the results of the analyses with an existing experimental result. Parametric studies of the effects of the externally reinforced FRP on the load capacity of reinforced concrete (RC) beams and concrete plates are performed to demonstrate the practicality and the efficiency of the proposed models.

• 한국정보통신학회논문지
• /
• 제20권3호
• /
• pp.639-646
• /
• 2016

본 연구에서는 특수한 상황(미끄러짐 발생 및 회전관성이 부하로 작용하는 경우)에서의 회전 엔코더 기반 측정방법의 단점을 극복하기 위하여 광 변위센서(ADNS-9500)를 사용한 비접촉식 변위 측정방법을 제안하였다. 정확한 변위 측정을 위해 데이터 수집 보드와 랩뷰를 활용하여 실험적으로 광 변위센서의 성능을 분석하였으며, 반복실험을 통해 실험조건(측정방향, 속도, 가속도, 높이, 표면 재질)에 따른 광 변위센서의 성능특성을 파악하였다. 성능실험 결과, 광 변위센서를 사용하여 정확하게 평면운동을 측정하기 위해서는 광 변위센서와 지면(대상 물체의 표면)과의 높이를 2.4 mm-3.2 mm로 일정하게 유지시켜야 하며, 각각의 축 방향, 속도, 표면 재질을 고려하여 민감도를 수정하여 변위 계산식에 적용해야 하는 것을 확인하였다.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.43-52
• /
• 2010

In this study, the shapes of the wheel and rail are represented by using 3-dimensional surface functions with surface parameters and a 3-dimensional wheel-rail contact analysis is presented. A whole numerical solution of wheel-rail contact at tread and flange including 2-point contacts can be achieved with the proposed numerical algorithm. Kinematic characteristics such as variances of vertical displacement and roll angle, and variance of wheel radius difference for arbitrary yaw and lateral displacement of wheelset, are determined for the KTX wheel-rail pair as an example. The condition of yaw and lateral displacement occurring 2-point contacts to analyze derailment are compared between standard and worn wheels. Differences of contact characteristics between curved and straight rails are also analyzed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.772-775
• /
• 2003

A bushing is a device used in automotive suspension systems to reduce the load transmitted from the wheel to the frame of the vehicle. A bushing is a hollow cylinder, which is bonded to a solid steel shaft at its inner surface and a steel sleeve at its outer surface. The relation between the force applied to the shaft and the relative deformation of a bushing is nonlinear and exhibits features of viscoelasticity. A force-displacement relation for bushings is important for multibody dynamics numerical simulations. For the nonlinear viscoelastic axial response, Pipkin-Rogers model, the direct relation of force and displacement, has been derived from Lianis model and the sinusoidal input was used for Pipkin-Rogers model, and the affection of displacement with frequency change was studied with Pipkin-Rogers model.

• 한국응용과학기술학회지
• /
• 제16권3호
• /
• pp.193-198
• /
• 1999

Maxwell displacement current(MDC) measuring technique has been applied on the study of monolayers of fatty acid. The displacement current was generated from monolayers on the water surface by monolayer compression and expansion. Displacement current was generated when the area per molecule was about $130{\AA}^2$. MDCs were investigated in connection with monolayer compression cycles. It was found that the current pulses were generated over the entire range of molecular area, and the maximum of MDC appeared at the molecular area just before the initial rise of surface pressure in compression cycles. We investigated the change in absorption spectra of the fatty acid(8A5H) monolayer LB film due to cis-trans photoisomerization. It was found that the absorption spectrum of the 8A5H LB film was induce to photoisomerization by alternate irradiation with UV and visible light irradiation.