• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.282-287
• /
• 2006

Viscosities of $LaCl_3-NaCl$ binary melts were measured by the capillary method over the range of their liquidus temperatures to about 1200K. The cell constant were determined by using pure water. The results obtained are summerized as follows: Viscosities were decreased with the content of NaCl for all over the composition range of binary melts. Composition - viscosity relation for the binary melts show a non-linear from the additivity line and the deviations shows a maximum at about 60 mol% NaCl. This suggests the existence of the complex ion of $LaCl_4^-$ in the melt. Activation energy for viscous flow of the binary melts decrease monotonously with the increasing content of NaCl.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.360-365
• /
• 1999

The combustion process was applied to synthesize the LiAlO2 powder with high specific surface area and pure crystalline ${\gamma}$-phase. For the combustion synthesis of LiAlO2 which is a binary-component oxide in-cluding lithium and aluminum ions the mixture of citric acid and urea with stoichiometric composition was selected as a promising fuel. The highest combustion temperature was measured in the reaction using the mixed fuel with a stoichiometric composition. The synthesized powder was very fine and its specific surface area was more than 15 m2/g.

• Corrosion Science and Technology
• /
• v.8 no.6
• /
• pp.227-231
• /
• 2009

Mg and Mg alloys have been used for lots of applications, including automobile industry, aerospace, mobile phone and computer parts owing to low density. However, Mg and Mg alloys have a restricted application because of poor corrosion properties. Thus, improved surface treatments are required to produce protective films that protect the substrate from corrosive environments. Environmental friendly Plasma Electrolytic Oxidation (PEO) has been widely investigated on magnesium alloys. PEO process combines electrochemical oxidation with plasma treatment in the aqueous solution. In this study, AZ91 Mg alloys were treated by PEO process in controlling the current with PC condition and treated time, concentration of NaF, NaOH, and $Na_2SiO_3$. The surface morphology and phase composition were analyzed using SEM, EDS and XRD. The potentiodynamic polarization tests were carried out for the analysis of corrosion properties of specimen. Additionally, salt spray tests were carried out to examine and compare the corrosion properties of the PEO treated Mg alloys.

• 보존과학연구
• /
• s.20
• /
• pp.81-90
• /
• 1999

We performed the non-destructive analysis of objects excavated at the Tomb of Mich’un-ri in Ch’ung-won. We analysed components using of Energy Dispersive X-Ray Micro-Fluorescence Analyzer. Glass bead inlaid with silver was classified as K2O-CaO-SiO2 type of glass. Purity of silver inlaid in the surface was verified above 97%.All small ear-ring were made by rolling up gold broad to a bronze wick. The composition ratio of Au : Ag has significantly higher 87 : 11 than bigear-ring. As a result of composition analysis of a welded part with big ear-ring, it contained the more Cu, Hg contents and the less Au, Ag contents than the surface of big ear-ring.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.4
• /
• pp.225-229
• /
• 1990

Solubility Products of metal oxides, such as Al2O3 and UO2 in KCl-LiCl eutectic composition was calculated by using an exact an exact thermodynamic. The values for Al2O3 ThO2 and UO2 were found to be 2.51$\times$10-27, 4.97$\times$10-15and 2.17$\times$10-12in mole per liter basis at 743 K, respectively. The correlation of theoretical values with those of experiment were in good agreement. It is worth to note that the exact cycle method was proved to be satisfactory in making predictions of solubillities and also solubility products of sparingly soluble metal oxides in an ionic salt system.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.3
• /
• pp.100-104
• /
• 2015

The nickel alloys gets a great deal of attention due to their good mechanical, chemical and magnetic properties. Especially Ni-P alloy systems are very attractive due to their good corrosion resistance and the wear resistance in important technological applications. In this study, the effects of phosphorus acid concentration in plating solution on composition of Ni-P alloy coatings were studied. The Ni-P electrodeposits of the various P contents were investigated in order to understand effect of the composition on mechanical properties of Ni-P electrodeposits. The mechanical properties of electrodeposits increased as the P content in electrodeposits increase. The results of mechanical properties were explained by grain size and P solid solution effect. The effects of heat treatment on mechanical properties of Ni-P alloy coatings were also studied.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.4
• /
• pp.197-206
• /
• 1989

The Composition and throwing power-of Pb-Sn alloy deposits are investigated in tems of the pulse parameters in pulse plating. Microhardness and intermal srress of alloy deposots are measured. The current efficiency of pulse plating is lower than that of D.C.plating while cathode overpotential and macro-throwing power noticebly increase with increasing peak current density. The Pb content of P.C. plated alloy deposits with increasing average current density, is relatively lower than of D.C. plated deposits at the same average current density. The internal stress of Pb-Sn alloy is not detected and the microhardness are 9.0kg/mm2 and 11kg/mm2 for D.C. plated P.C. plated deposits, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.4
• /
• pp.303-312
• /
• 2001

Composition and microstructure of the tin-zinc alloys electroplated in gluconate bath were studied according to pulse current parameters. The cathode current efficiency increased with both the mean current density and the off-time decrease. Zinc content of the alloy deposits increased with increasing mean current density, while it decreased noticebly with increasing the off-time from 10-30ms to 100-150ms. The preferred orientation of the alloy deposits changed with the increase of peak current density in the sequence of (220)longrightarrow(220)+(420) or (220)+(420)+(321) mixed structure. The equiaxed grain size of the alloy increased with the increase of off-time and the decrease of mean current density.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.5
• /
• pp.301-306
• /
• 2004

Electric Conductivities of $LaCl_3$-LiCl binary melts have been measured by the Kohlausch bridge method over the range of their liquidus temperatures to about 1200 K. The electric conductivity increases with the content of LiCl for all over the composition range of binary melts. Composition dependence of the electric conductivity and molar conductivity for the binary melt shows a non-linear relation from the additivity line, and the deviations displays a maximum value at about 60 mol % LiCl. This suggest the existence of the complex ion of$ LaCl_{4}^{-}$ in the melt. Activation energy for electric conductivity of the binary melts decrease monotonously with increasing content of LiCl.l.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.4
• /
• pp.297-302
• /
• 2001

As GA (Hot dip galvannealed steel sheet) has good corrosion resistance, weldability and paintability as well as excellent formability, it's demand is rapidly increasing for automotive panels. The GA coated layers are composed of several kinds of brittle Fe-Zn Metallic compounds which are susceptible to powdering during the press forming, however, very careful controls of manufacturing conditions such as galvannealing heat-treatment or bath composition are essential to meet with the required quality of automotive use. In this study the required characteristics of automotive panel are practically surveyed in detail and the appropriate manufacturing conditions of galvannealing or bath composition have experimentally investigated by using the various analyzing and simulating equipments. The result in this study indicated that the corrosion resistance at the cut edges was improved by increasing of coating weight and decreasing of thickness of sheet steels.