• 한국수자원학회논문집
• /
• 제49권5호
• /
• pp.399-410
• /
• 2016

유속계수는 상수도 설계, 운영, 유지관리 등의 과정에서 항상 현장 실정이 고려된 값이 사용되어야 한다. 본 연구는 광역상수도 정밀안전진단 과정에서의 174개 실측자료를 바탕으로 유속계수와 주요 인자 간의 관계를 통계적 기법을 활용하여 분석하였다. 이들 관계를 분석하기 위해서 교차분석, 일원배치 분산분석, 상관분석 등을 수행하였으며, 그 결과 유속계수와 사용년수 및 관경이 높은 상관관계를 나타내고 여러 범주형 자료 형태 영향인자 중에 내부도장재가 상대적으로 유속계수에 많은 영향을 주는 것으로 검토되었다. 반면 다중회귀분석의 결과에서는 사용년수, 관경 및 수종이 중요한 영향인자인 것으로 검토되었다. 군집분석 결과, 유속계수는 기본적으로 사용년수 약 20년, 관경 1500mm를 기준으로 분류되는 경향이 있었으며, 유속계수는 전반적으로 사용년수에 많은 영향은 받으나 대구경 관에서는 상대적으로 사용년수보다 관경에 많은 영향을 받는 것으로 검토되었다. 마지막으로 본 연구에서는 회귀분석과 군집분석을 사용하여 유속계수 산정식들을 제안하였으며, 이러한 추정식들은 추후 광역상수도의 유속계수 결정 및 사용 시에 판단기준이 될 수 있을 것으로 판단된다.

• 상하수도학회지
• /
• 제32권1호
• /
• pp.37-45
• /
• 2018

This study develops a model to estimate the economic life of the large-diameter water supply pipeline in Korea by supplementing existing methods used to perform similar calculations. To evaluate the developed methodology, the model was applied to the actual target area with the conveyance pipe in P waterworks. The application yielded an economic life computation of 39.7 years, considering the cost of damages, maintenance, and renewal of the pipeline. Based on a sensitivity analysis of the derived results, the most important factor influencing the economic life expectancy was the predicted failure rate. The methodology for estimating the economic life of the water supply pipeline proposed in this study is one of the core processes of basic waterworks facility management planning. Therefore, the methods and results proposed in this study may be applied to asset management planning for water service providers.

• 한국유체기계학회 논문집
• /
• 제12권5호
• /
• pp.19-24
• /
• 2009

This paper is performed to find out the stability of water-hammer in pipe line and pump station that is happened when additional water needs demanded. At first, the water supply construction project is planned to supply $6,000\;m^3/day$ through 17.9 km pipe line. But additional demand ($1,200\;m^3/day$) happened from Cheong-ra water reservoir. In this situation, air-chamber($4\;m^3$) and vacuum breaker valve(${\varphi}100\;mm$) are needed to prevent water-hammer. When the additional water is supplied, the existing facilities (air-chamber, vacuum breaker valve) are sufficient to alleviate shock not changing capacity alteration, judging from the airspace change and rise. Therefore, there is no problem for water-hammer by installing air-chamber($4\;m^3$) and vacuum breaker valve(${\varphi}100\;mm$) at the top of Yeo-ju hill.

• 상하수도학회지
• /
• 제26권4호
• /
• pp.555-563
• /
• 2012

Due to the importance of energy-saving and CO2 reduction is being emphasized in the world, efforts to find a solution for the problems is increasing rapidly. In particular, the renewable energy is on understanding as a breakthrough for the protection of the environment and the economic development, so it is intensively fostered as future industries. Developed countries are already pursuing policy and technology development related with renewable energy. In this paper, we will develop MHD(Magneto Hydro Dynamics) technology to supply the commercial power that can is targeted at water pipe related with hydro power among renewable energy technologies. Kinetic energy of fluid flowing in the water pipe is converted into electric power. It allows stable power supply to the various sensors and devices on water pipe. We have performed several experiments to verify the application possibility of the developed technologies and present the result and a method of performance improvement of the technologies.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.585-589
• /
• 2009

Extruder is divided to greatly three part at extrusion process. First, by hopper(Hopper) second, barrel(Barrel) with Screw that is point of extruder and third that is raw material supply wealth extrusion into dies(DIES) Part that decide shape of do product greatly divide. Hopper is role that distribute in raw material supply wealth (Feeding zone) of Screw preserving raw material in state of high quality how at extrusion process, and make distributed raw material as Screw in barrel rotates and 3 stage and inflicting heat and pressure raw material melting(Melting) state. And raw material of melting state Screw's measuring stoker(Metering zone) whereabouts anaphora do and product is completed through pipe channel of dies. Dies that is the most important as Screw in extrusion is part that is last part of melting state process of raw material and causes huge effect in quality of product. If more than design of dies happens, manufacture itself of dies is hard, but there are a lot of amount of losses accordingly. In this research, make pipe channel that raw material of melting state flows in dies can present dies basic design method through flow analysis of ideal pipe channel using CFdesign.

• 한국산업융합학회 논문집
• /
• 제24권4_2호
• /
• pp.475-480
• /
• 2021

The purpose of this study is to obtain the natural frequency of fuel supply pipes for vehicle engines through modal analysis and testing and compare the resulting values to ensure the reliability of the analysis. In other words, in this study, we obtain the unique frequency of the fuel pipe of the vehicle engine through analysis and testing and compare its results. Comparing the natural frequency obtained through analysis and testing, the first and third vibration modes obtained accurate natural frequency results of less than 1% and very similar results of less than 5% maximum error over the fourth vibration modes. These results are determined that if design changes of fuel pipes are made depending on the vehicle in the future, there will be no problem in obtaining the natural frequency of pipes that have been changed by analysis. Through future analysis and testing, durability and stability evaluation of connections of fuel supply pipes for vehicle engines will be carried out.

• 한국분무공학회지
• /
• 제7권2호
• /
• pp.31-36
• /
• 2002

According to the improvement of PC performance, it is expected that calorific value, which causes PC to malfunction, is increased. Therefore, the development of new cooling system is recently required. As the method to solve this problem, we applied loop heat pipe to PC cooling system. The advantage of the loop heat pipe is that it has a small size, light weight, simple shape, long life and it has a good performance on heat transfer, no-noise, wide range of applicable temperature and no supply of power from the outside. It is confirmed that loop heat pipe reduces thermal resistance and has a good performance on PC cooling.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.453-458
• /
• 2008

Pump of high lift use to development of a technological level according as a building grow big. Water-Hammer to increase by valve of fast to closing agreeably to pipe laying to accept electronic valve, because by a damage of piping-system and the devil knows injury of vibration. Water-Hammer take a low effect to various method for solve. A New type manufacture develop and testing of pipe line to same to axis use to accumulator for water-Hammer to low effect and liner control of pressure. Impact-pressure of absorption ability and confirmation to decrease of vibration level through to preexistence manufactures and comparative test. Water-hammer and pipe vibration make low of piping system.

• 한국안전학회지
• /
• 제11권3호
• /
• pp.97-103
• /
• 1996

The welding characteristics of polyethylene pipe for gas varying temperature and pressure is analyzed in this study. The analysis is very important to studying the weldability of PE pipe as well as is useful for its welding data. The specimens have the same welding conditions. Experimental data of the bead width, height and thickness for PE welding are measured with tool projector, Experimental results for PE welding Indicated that temperature more than pressure have influence on the weldability. It was confirmed that optimal PE welding within the limits of $210^{\circ}C$ and 15kg/$cm^2$ have high welding performance in comparison with other conditions. These results are very important to improve the safety and to reliable welding components of PE gas pipe.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2004년도 Proceedings of ISRS 2004
• /
• pp.17-20
• /
• 2004

The purpose of this study is to arrange the digital maps of Hamamatsu City and to construct the map information system to support the prediction and restoration of Tokai earthquake disasters. The authors arrange the land condition map and compute the populations of each land surface conditions and revealed that $37\%$ of the whole population lives in the safe land, but $63\%$ lives in the rather unsafe surface condition. The authors also arrange the digital map of the main lines of water supply pipe lines in corporation with the Hamamatsu City Water Supply Department and revealed the rather dangerous pipe line area in case of Tokai earthquake.