• 상하수도학회지
• /
• 제27권1호
• /
• pp.129-138
• /
• 2013

Water interruption is often caused by a rupture in the branch-like singular pipeline. This will cause critical complaints from household and may decrease public service quality. As an alternative of singular pipeline, additional parallel pipeline could be installed for sustainable water supply. This system is called double pipeline system and able to be utilized for water transmission line between treatment plant and distribution reservoir. Construction of double pipeline was thought to increase capital cost, which can be an issue to waterworks authorities. Reducing capital cost was possible by means of installing connectors between two parallel pipelines because of reduced diameter of each pipe. To obtain optimal design condition for connectors, it was necessary to compare water pressure according to accident location, to investigate flow according to connection pipe spacing, connection pipe diameter, and aging of pipe. Reliable and economical connection layouts were determined based on these results. The cost estimation for each design condition was carried out. Cost was approximately reduced by 20 ~ 30 % compared to the double pipeline without connections. In addition to this, connection between double pipelines could expect extra benefits for maintenance since the pipe could be repaired and rehabilitated without interruption.

• 설비공학논문집
• /
• 제5권3호
• /
• pp.157-168
• /
• 1993

Pipe network of hot water heat supply system in an apartment house was analyzed. Flowrate and supply heat capacity of each household in which constant flowrate balancing valve is installed in a single zone system were calculated and the results were investigated. In the existing piping system, the non-uniformity of heat supply with floors due to the static pressure and temperature difference between supply main and return main can not be avoided and this tendency get intense with the increase of the height of building. The non-uniformity of heat supply can be prevented by the installation of balancing valve at each household, however if the performance of supply pump is not sufficient to overcome the energy loss due to the installation of balancing valve for constant flow rate or if the selection of the valve capacity is not adequate, the valves will may lose their controllability.

• 미생물학회지
• /
• 제49권4호
• /
• pp.313-320
• /
• 2013

정수처리 시설에서 급 배수관으로 많이 사용되는 스테인리스관과 동관에 형성되는 생물막의 특성에 대해 16주 동안 조사하였다. 생물막 반응기는 실제 배급수관의 구조와 유사하게 설계하였으며, 정수처리장으로 유입되는 상수원수와 약품혼화 응집수, 침전수, 여과수, 처리수를 사용하였다. 평균 종속영양세균수는 $1.6{\times}10^4CFU/ml$, $5.8{\times}10^3CFU/ml$, $1.8{\times}10^3CFU/ml$, $1.3{\times}10^2CFU/ml$, 1 CFU/ml로 각 처리 과정을 거치면서 감소하였다. 스테인리스관과 동관에 형성된 생물막 세균수는 원수, 응집수, 침전수에서 2주만에 $2.9{\times}10^3CFU/cm^2$ 이상으로 증가하였고, 동관보다 스테인리스관에서 생물막 세균수가 높게 검출되었다. 여과수(평균 잔류염소 0.44 mg/L)에서는 두 관 재질에 따른 생물막 세균수의 명확한 차이는 없었으며, 5주 이후부터 두 관재질 모두 $18CFU/cm^2$ 이하의 생물막 세균이 검출되었다. 정수(평균 잔류염소 0.88 mg/L)에서는 두 관 재질 모두 생물막 세균이 검출되지 않았다. DGGE 분석결과, 원수, 응집수, 침전수에서 스테인리스관은 Sphingomonadaceae가 우점이였고, 동관에서는 Bradyrhizobiaceae와 함께 Sphingomonadaceae도 우점이였다. 여과수의경우, 5주차 이후 스테인리스관과 동관에 형성된 생물막에서 Propionibacterium sp., Sphingomonas sp., Escherichia sp. 등과 유사한 16S rRNA 유전자 서열을 가지는 밴드들이 검출되었다. 종 풍부도 및 다양성은 동관에 비해 스테인리스관이 더 높게 나타났다.

• 상하수도학회지
• /
• 제13권1호
• /
• pp.95-112
• /
• 1999

In this research, it is proposed that optimization method is introduced and applied to the design of pipeline system in multi-regional water supply project, which has been constructed to settle the regional unbalance problems of available water resources. For the purpose, interface programs are developed to integrate linear programming model and KYPIPE model which is used for optimization and hydraulic analysis, respectively. The developed program is applied to the pipeline system design of multi-regional water supply project. The optimal diameters from the application of linear programming technique are compared with those from conventional method that is time-consuming and tedious trail and error process. Since the conventional design largely depends upon the experience of designers and the results of general hydraulic analysis, it can not be reasonable and consistent. The application of linear programming technique can make it possible to design pipeline system optimally by using same design factors of general hydraulic models. The model can select commercial discrete pipe diameter as optimal size by using pipe length as decision variables. The developed model is applied to Pohang multi-regional water supply system design with two different objective functions, which are initial construction cost and annual cost including electric cost. As results, it is calculated that the initial construction cost of 1,449,740 thousand won is saved and annual cost of 128,951 thousand won is saved for a year within study year. Also, the optimal site of pump station is selected on 5th pipe, which is located between the diverging junction to Kangdong(2) province and the diverging junction to Cheonbuk province. It is explained that pump cost is less than pipe cost in this application case study due to little pump station scale. In the case of water supply with large pump capacity, it is reasonal that the increase of pipe size is more efficient instead the increase of pump station capacity to save annual cost.

• 한국지반환경공학회 논문집
• /
• 제9권3호
• /
• pp.11-15
• /
• 2008

대구경 상수도 관로는 제작 및 경제성 요인에 의해 주로 강관을 사용해 오고 있다. 상수도시설기준(건교부, 1992)에 강관두께를 결정하는 기준을 제시하고 있다. 그러나, 이 기준에는 강관 두께를 결정하는 체계적인 기준이 없다. 그래서, 매설관로에는 적용이 부적합한 Stewart 공식을 적용하여 강관두께를 결정해 왔다. 개정된 상수도시설기준(환경부, 1997) 에 부합되도록 지반여건과 각종응력을 고려하여 강관두께를 산정하였다. 그 결과를 기존의 방법에 의해 산정된 결과와 비교 검토한 후 최적 강관두께를 결정하는 방법을 제시하였다.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.269-277
• /
• 2002

Dynamic characteristics of water hammer arresters installed in a building water supply system have been investigated numerically by utilizing a commercial rode that employs the method of characteristics. Some preliminary results with those arresters produced in this study agree well with the previously reported. Then, the arresters have been incorporated into a water supply pipe system of a $59m^2$ apartment unit constructed by a leading construction company, and their dynamic characteristics, especially on the reduction in the water hammer pressure, are investigated. It is found that the setting of the arresters in the pipe system, which is recommended by the company, may not be proper for reducing the pressure to less than 1082.0 kPa when buick-closure valves in the pipe system are closed within 30 ms at the static pressure of 542.6 kPa. More arresters in the system may be required to meet a pressure criteria.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제9권2호
• /
• pp.51-61
• /
• 2001

A numerical study has been conducted to characterize the transient pressure in a simple water supply pipe system with an air chamber by utilizing a commercial code that employs the method of characteristics. Some results produced for validation in the study agree quite well with the previously reported. Several parameters are than varied. Among them are the valve closure time, the wave speed, the static pressure, the polytropic exponent, the air chamber volume, the diameter and the shape of orifice in the air chamber, etc, while the water temperature and velocity are kept constant at $20^\circ{C}$ and 0.8m/s, respectively. Results reported in this parametric study may be useful to understand the unsteady behavior of the system.

• 한국환경과학회지
• /
• 제31권1호
• /
• pp.33-42
• /
• 2022

The objective of this study is to determine the appropriate size of the inlet pipe diameter and thereby conduct hydraulic analysis for the Korean water distribution network. To this end, the data tables for equivalent pipe diameters and outflow rates presently employed in Korea were adopted. By incorporating the table of equivalent pipe diameters, it was found that the size of the inlet pipe diameter was overestimated, which can cause shortage of water pressure and malfunctioning or insufficiency of outflow rate in the corresponding adjacent region. However, by conducting hydraulic analysis based on the table of outflow rates, relatively reasonable flow rates were observed. Furthermore, by comparing the real demand-driven analysis (RDDA) approach and demand-driven analysis (DDA) approach toward managing the huge water demand, it was observed that DDA could not effectively respond to real hourly usage conditions, whereas RDDA (which reflects the hourly effects of inlet pipe diameter and storage tanks) demonstrated results similar to that of real water supply.

• 한국지열·수열에너지학회논문집
• /
• 제13권1호
• /
• pp.1-6
• /
• 2017

In this paper, the flow characteristics of water in the water supply pipes of a WBC array were evaluated. We simulated the flow velocities and pressures for a standard pipe, an expansion pipe with a concentric reducer, and an expansion pipe with an eccentric reducer using computational fluid dynamics. In the case of the standard pipe, when the inlet flow velocities were 0.5 m/s and 2.0 m/s, the maximum flow velocities at the center of the WBC array were 0.54 m/s and 2.74 m/s, respectively, which were the greatest values among those of all the pipe models considered. In the case of the expansion pipe, the maximum flow velocities at the center of the WBC array were almost the same under the same conditions regardless of the type of reducer. The pressure losses in the pipe due to the concentric and eccentric reducers were found to be (165.09 ${\times}$ inlet $velocity^{1.6677}$) and (210.98 ${\times}$ inlet $velocity^{1.6478}$), respectively. The coefficient of determination at this time was greater than 0.99 and was the same for both the models. As a simulation result, it was found that in order to reduce the pressure loss when pipe with WBC array is connected with a conventional pipe, diameter of the pipe with WBC array at that section should be enlarged by one step, and then connected to the conventional pipe with a concentric reducer.

• 한국가스학회지
• /
• 제11권2호통권35호
• /
• pp.1-4
• /
• 2007

가스는 산지에 따라 그 조성이 다르며, 이러한 가스조성의 변화는 가스 배관망 내 발생하는 압력손실 값에 영향을 미치므로 매우 중요한 고려 요소이다. 그러므로 평균 가스조성(비중) 대신 각 인입지점으로 인입되는 가스가 실제로 가지고 있는 가스조성을 사용하는 것이 배관망 해석 수행 시 더욱 정확한 결과를 얻을 수 있다. 본 연구에서는 가스 배관망에서 인입지점으로 인입되는 가스 조성을 평균값이 아닌 실제 조성을 사용할 경우 소비자에게 가스를 공급하는 공급지점의 공급압력에 미치는 영향을 분석하였다. 본 연구결과를 비교하기 위하여 각 인입지점의 가스조성을 평균하여 모든 인입지점의 가스조성으로 동일하게 사용하여 산출된 압력 값을 사용하였다. 그 결과, 실제 가스조성 고려 시 공급압력에 미치는 영향은 상당한 수준이므로 천연가스 산업현장의 공급 배관망에 대한 배관망해석 수행 시 실제의 가스조성을 반드시 고려하여야 정확한 분석결과를 얻을 수 있음을 알 수 있었다.