• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2003년도 추계학술대회 논문집
• /
• pp.91-94
• /
• 2003

The present study addresses experimental results to investigate the details of the near field flow structures produced in the under-expanded, dual, coaxial, swirling, jet. The sonic swilling jets are emitted from a sonic inner nozzle and the outer annular nozzle produces the co/counter swirling streams against the primary swirling jet, respectively. The interactions between both the secondary annular swirling and primary inner supersonic swirling jets are quantified by the pilot impact and static pressure measurements, and visualized by using the Schlieren optical method. The experiment has been performed fur different swirl intensities and pressure ratios. The results obtained show that the secondary co-swirling jet significantly changes the inner under-expanded swirling jet, such as the recirculation zone, pressure distribution, through strong interactions between both the swirling jets, and the effect of the secondary counter-swirling jet on the primary inner jet is similar to the secondary co-swirl jet case.

• 대한기계학회논문집B
• /
• 제29권1호
• /
• pp.80-86
• /
• 2005

This study presents numerical solutions of the two-dimensional Navier-Stokes equations for supersonic unsteady flow in a convergent-divergent nozzle with heat addition. The TVD scheme in generalized coordinates is employed in order to calculate the moving shock waves caused by thermal choking. We discuss on transient characteristics, start and unstart phenomena, fluctuations of specific thrust caused by thermal choking and viscous effects. We prove that the control of separation of boundary layer is the most important key problem to prevent the thermal choking.

• 한국유체기계학회 논문집
• /
• 제18권4호
• /
• pp.13-21
• /
• 2015

The system design of the Organic Rankine Cycle(ORC) is greatly influenced by the thermal properties such as the temperature or the thermal capacity of heat source. Typically waste heat, solar energy, geothermal energy, and so on are used as the heat source for the ORC. However, thermal energy supplying from these kinds of heat sources cannot be provided constantly. Hence, an experimental study was conducted to utilize fluctuating thermal energy efficiently. For this experiment, an impulse turbine and supersonic nozzles were applied and the supersonic nozzle was used to increase the velocity at the nozzle exit. In addition, these nozzles were used to adjust the mass flowrate depending on the amount of the supplied thermal energy. The experiment was conducted with maximum three nozzles due to the capacity of thermal energy. The experimented results were compared with the predicted results. The experiment showed that the useful output power could be producted from low-grade thermal energy as well as fluctuating thermal energy.

• 한국군사과학기술학회지
• /
• 제6권4호
• /
• pp.124-131
• /
• 2003

When a secondary gaseous flow is injected vertically into a supersonic flow through circular nozzle, a complicated structure of flow field is produced around the injection area. The interaction between the two streams produces a strong bow shock wane on the upstream side of the side-jet. The results show that bow shock wave and turbulent boundary layer interaction induces the boundary layer separation in front of the side-jet. This study is to analyze the structure of flow fields and distribution of surface pressure on the flat plate according to total pressure ratio using a supersonic cold-flow system and also to study the control force of affected side-jet. The nozzle of main flow was designed to have Mach 2.88 at the exit. The injector has a sonic nozzle with 4mm diameter at the exit of the side-jet. In experiments, The oil flow visualization using a silicone oil and ink was conducted in order to analyze the structure of flow fields around the side-jet. The flow fields are visualized using the schlieren method. In this study, a computational fluid dynamic solution is also compared with experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2145-2150
• /
• 2003

Ejector system is one of fluid machinery which can entrain the fluid in low pressure part and transport it to the higher pressure part. The ejector system has been widely used for the purpose of obtaining high-vacuum state, fluid transport, thrust augmentation, etc. It can transport a large capacity of fluid with relatively small device of no any moving parts, and thus seldom causes mechanical troubles. However, the conventional ejector system has been pointed out that its overall efficiency is quite low compared with other fluid machinery since it is derived by only the pure shear stresses. In the present study, 4, 6, and 8 lobed petal nozzles with a design Mach number of 1.7 are adopted as a primary nozzle to improve the ejector performance, and are compared with a conventional circular nozzle. The static pressures along the diffuser wall are measured to qualify the flow field inside the supersonic petal ejector system.

• 신재생에너지
• /
• 제10권1호
• /
• pp.6-19
• /
• 2014

Organic Rankine cycle (ORC) has been widely used to convert renewable energy such as solar energy, geothermal energy, or waste energy etc., to electric power. For a small scale output power less than 10 kW, turbo-expander is not widely used than positive displacement expander. However, the turbo-expander has merits that it can operate well at off-design points. Usually, the available thermal energy for a small scale ORC is not supplied continuously. So, the mass flowrate should be adjusted in the expander to maintain the cycle. In this study, nozzles was adopted as stator to control the mass flowrate, and radial-type turbine was used as expander. The turbine operated at partial admission. R245fa was adopted as working fluid, and supersonic nozzle was designed to get the supersonic flow at the nozzle exit. When the inlet operating condition of the working fluid was varied corresponding to the fluctuation of the available thermal energy, optimal operating condition was investigated at off-design due to the variation of mass flowrate.

• 한국산업융합학회 논문집
• /
• 제2권2호
• /
• pp.115-124
• /
• 1999

The interaction of weak normal shock wave with turbulent boundary layer in a supersonic nozzle was investigated experimentally by wall static pressure measurements and by schlieren optical observations. The lime-mean flow in the interaction region was classified into four patterns according to the ratio of the pressure $p_k$ at the first kink point in the pressure distribution of the interaction region to the pressure $p_1$ just upstream of the shock. It is shown for any flow pattern that the wall static pressure rise near the shock foot can be described by the "free interaction" which is defined by Chapman et al. The ratio of the triple point height $h_t$ of the bifurcated shock to the undisturbed boundary layer thickness ${\delta}_1$ upstream of the interaction increases with the upstream Mach number $M_1$, and for a fixed $M_1$, the normalized triple point height $h_t/{\delta}_1$ decreases with increasing ${\delta}_1/h$, where h is the duct half-height.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.34-39
• /
• 2005

본 논문에서는 3차원 초음속 노즐 형상 변수에 따른 부분입사형 터빈의 유동 및 성능 특성을 알아보기 위하여 3차원 노즐 형상 변수를 노즐 모양 및 노즐 출구 단면 형상으로 설정하여 전산해석을 실시하였다. 먼저 노즐 모양에 따른 유동 및 성능 특성을 비교해 본 결과, 사각형 노즐이 원형 노즐보다 축방향 간극내에서 발생하는 전압력 손실이 적었으며, 이로 인하여 파워가 약 1.5% 증가하였다. 다음으로 사각형 노즐출구단면의 면적에 따른 유동 및 성능 특성을 비교해 본 결과, 노즐 출구 단면과 로터의 hub/tip 사이의 간극과 노즐간의 간격이 터빈 성능에 크게 영향을 줌을 확인할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.297-305
• /
• 2006

본 논문에서는 터빈의 형상 변수에 따른 부분흡입형 초음속 터빈 손실 특성을 분석하기 위하여 초음속 노즐 형상, 축방향 간극 길이, 로터 앞전의 모서리각에 따른 초음속 터빈내 유동 해석을 실시하였다. 먼저 축방향 간극을 진행하면서 발생하는 유동의 익렬 팁방향의 휘어짐은 초음속 노즐 형상에 크게 영향을 받는다. 다음으로 모서리각은 익렬 앞전에서 발생하는 충격파등의 강도를 결정한다. 마지막으로 축방향 간극에서 발생하는 유동의 확산 및 혼합은 축방향 간극 길이에 크게 영향을 받았다. 따라서 터빈내에서 발생하는 손실 중 유체역학적 손실은 노즐 형상과 로터 앞전의 모서리각에 의해 결정되었으며, 부분 흡입 손실은 노즐 형상 및 축방향 간극 길이에 영향을 받았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.497-500
• /
• 2011

고체 추진기관의 노즐 소재로 사용하기 위하여 Zirconia로 코팅된 SCM-440과 STS-630 적용 노즐의 열구조 안전성에 관한 시험 평가를 수행하였다. 각 노즐에 플라즈마 스프레이 기법으로 0.15 mm 코팅하였으며, Zirconia 코팅 노즐의 열차폐 효율과 열적 내구성 평가를 수행하였다. 두 소재의 노즐목에서 Zirconia 코팅한 노즐은 코팅하지 않은 노즐 보다 70% 높은 열차폐 효율을 갖는 결과를 나타냈다. SCM-440이 STS-630보다 온도 상승률이 더 높으며, 노즐 확장부에서 더 높은 온도를 가지는 것을 확인하였다. 따라서 플라즈마 기법의 Zirconia 코팅이 초음속 노즐의 열구조 안전성에 유용함을 알 수 있었다.