• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.244-246
• /
• 2004

Compared with other transport means, safety and timeliness are the merits of railways. Unexpectedly when accident happens, much time and human strength are required to cope with the accident. And for swift recovery, systematic rehabilitation is needed. Recently using MTS(Moving picture Transmission System), we can perform accident rehabilitation and recording work efficiently. MTS is the device that transmits continuous picture information from accident field to control center. We are developing the appropriate system to railway situation to make use of the existing information communication technology, processing technology of video-tex, super high speed transmission technology through fiber-optic, copper cable and network description of information Technology, etc. If these communication-based can technologies are applied to railway system, railway managers can control the accident by inspecting the picture of accident field and can contribute to the safe train operation and the improvement of railway management. In this paper, we investigate the connecting methods when optical fiber is used for moving picture data transmission of train accidents, and its problems. And, we validate MTS's performance through about 28km section of field test.

• Textile Coloration and Finishing
• /
• v.24 no.2
• /
• pp.131-137
• /
• 2012

para-Aramid fibers were treated by low-temperature plasma to improve the adhesion. The surface of para-aramid fibers were treated with gaseous plasma of several discharge power and treatment time in oxygen gas at 1Torr pressure. The treated fibers at low-temperature plasma were taken oxygen-containing functional groups and micro-crator on the surface. The modified fibers were measured by dynamic contact angle analyzer and XPS(X-ray photoelectron spectroscopy). The Interfacial adhesion properties of aramid fabric and polyurethane resin were determined by T-peel test. The surface of aramid fibers were observed by FE-SEM photographs. It was found that surface modification and chemical component ratio of the aramid fibers were improved wettability and adhesion characterization.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.14-20
• /
• 2017

Ultra high performance concrete is inevitably used in case of skyscraper and super long span bridge. In general, the flexural and the tensile strengths of concrete are lower than the compressive strength, so brittle cracks occur and energy absorption ability is lowered. In order to solve this problem, this study is intended to examine the effect of the steel fiber volume fraction and aspect ratio on the mechanical properties of ultra high performance concrete. In series I, 20-mm straight steel fiber was added with a volume fraction of 0, 1.0, 1.3, 1.5 and 2.0%. In series II, 16-mm steel fiber was added with a volume fraction of 0, 1, and 1.5%, and then mechanical properties were examined according to aspect ratio. In the results of experiment, a difference in compressive strength was insignificant. However, regarding the flexural strength and tensile strength, as the volume fraction and aspect ratio increased, flexural performance and tensile performance improved.

• Korean Journal of Materials Research
• /
• v.13 no.11
• /
• pp.749-755
• /
• 2003

A development of micropores of $CO_2$activated isotropic carbon fibers from TEM was observed. It was observed that the micropores of activated carbon fibers(ACFs) were consisted of slit-shaped pores(SP) and cylinder-shaped pores(CP). The SPs were formed between two parallel-carbon layers, and the CPs were formed at a place which is connected polygonally by more than two carbon layers. It was shown that the CPs of the ACFs were developed at high degree of burn-offs and at high activation temperature. The pore size distribution of the best ACF, which was observed at a highest value of specific surface area(3,495 $\m^2$/g), showed a continuous distribution in the range of about $4∼l5\AA$, and the median pore size was 6.7$\AA$. The super-high specific surface area of ACFs was found to be due to that the SPs were connected with a maximum size of 7∼8$\AA$ continuously, It is possible that the SPs should be formed in the ACFs in order to show super-high SSA.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.308-312
• /
• 2019

Polyphenylene sulfide (PPS) is a well-known super engineering plastic with a high melting temperature (above 290℃). It is generally insoluble under regular conditions. Therefore, it can be used for replacing metallic materials. Many researchers are looking at the possibility of replacing aluminum in the engine compartment of an automobile. However, studies on PPS are not common as compared to conventional engineering plastics because only a few companies produce super engineering plastics. In this research, the material properties of PPS composites containing two different kinds of glass fibers and produced under different processing temperatures were investigated. The tensile strength of the PPS composites increased as the processing temperature increased. Although glass fibers with similar aspect ratios were compounded under the same processing condition, one of them yielded a higher mechanical strength.

• Korean Journal of Optics and Photonics
• /
• v.32 no.6
• /
• pp.276-285
• /
• 2021

This paper reports the study of the line-beam optical system of the laser lift-off (LLO) equipment used in the OLED manufacturing process. To obtain both a long process depth and a narrow width of the line beam, even with the poor M² value of the laser source, the research is focused on the optical system, including the beam transformation unit (BTU). We also propose optical configurations for the super-Gaussian distribution and the fiber-based BTU for the flat-top distribution.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.6
• /
• pp.1589-1600
• /
• 1997

The construction of optical access network costs upper 40% in total installation cost of total optical network. Optimization of access network therefore is core in optical network. Advanced countries include EU, Japan and USA already have researched access network. This paper presents analysis of three broad-band fiber-optics subscriber loop architectures(HFC, ATM-PON, Super PON). The analyses focus on the specific demonstrated architectures and use component cost projections to estimate future network costs on a per-subscriber basis. We use TITAN(Tool for Introduction Scenarios and Techno-Economic Evaluation of The Access Network) model. We find that ATM-PON can deliver voice and ISDN data at installed first costs than the other architectures. This is due to the sharing bandwidth among a cluster of subscribers within Curb. This work intends to support establishing guidelines for strategic decisions regarding the development of the access network alternatives of different operators.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.2
• /
• pp.101-109
• /
• 2016

PURPOSE. To investigate the void parameters within the resin cements used for fiber post cementation by micro-CT (${\mu}CT$) and regional push-out bonding strength. MATERIALS AND METHODS. Twenty-one, single and round shaped roots were enlarged with a low-speed drill following by endodontic treatment. The roots were divided into three groups (n=7) and fiber posts were cemented with Maxcem Elite, Multilink N and Superbond C&B resin cements. Specimens were scanned using ${\mu}CT$ scanner at resolution of $13.7{\mu}m$. The number, area, and volume of voids between dentin and post were evaluated. A method of analysis based on the post segmentation was used, and coronal, middle and apical thirds considered separately. After the ${\mu}CT$ analysis, roots were embedded in epoxy resin and sectioned into 2 mm thick slices (63 sections in total). Push-out testing was performed with universal testing device at 0.5 mm/min cross-head speed. Data were analyzed with Kruskal-Wallis and Mann-Whitney U tests (${\alpha}=.05$). RESULTS. Overall, significant differences between the resin cements and the post level were observed in the void number, area, and volume (P<.05). Super-Bond C&B showed the most void formation ($44.86{\pm}22.71$). Multilink N showed the least void surface ($3.51{\pm}2.24mm^2$) and volume ($0.01{\pm}0.01mm^3$). Regional push-out bond strength of the cements was not different (P>.05). CONCLUSION. ${\mu}CT$ proved to be a powerful non-destructive 3D analysis tool for visualizing the void parameters. Multilink N had the lowest void parameters. When efficiency of all cements was evaluated, direct relationship between the post region and push-out bonding strength was not observed.

• Information and Communications Magazine
• /
• v.11 no.2
• /
• pp.77-89
• /
• 1994

High speed optical fiber transmission technology has been remarkably improved during the past 20 years. This paper presents recent research status and future technological issues for the future information society, that is, the Tb/s transmission by frequency division multiplexing and the ultra long-distance by optical soliton transmission. Erbium-doped fiber amplifier and recent optical technology have brought optical transmission system of up to 10 Gb/s to the point of commercialization. Taking into account the future super information highway, that is, B-ISDN network, ultra wide-band picture-based information can be provided for many subscribers via existing optical fiber cables. However, to achieve the high speed transmission, the technologies must be developed not only for transmission lines but also for transmission nodes. Since the conventional signal transmission/processing technique using electronics has the limit in its speed, novel photonic technology is being developed for this purpose. On the other hand, optical solitons propagate stably through optical fibers, without pulse broadening effect of the fiber dispersion. Since the pulse broadening effect becomes serious as the transmission speed increases, optical solitons is the important technologies to realize the high speed, long distance transmission.

• International Journal of Concrete Structures and Materials
• /
• v.18 no.1E
• /
• pp.29-34
• /
• 2006

Elastic modulus, tensile and bond capacities are important factors for developing an effective reinforcing action of a flexural member as a reinforcing material for concrete structures. Reinforcement must have enough bond capacity to prevent the relative slip between concrete and reinforcement. This paper presents an experimental study to clarify the bond capacity of prestressed carbon fiber reinforced polymer(CFRP) rod manufactured by an automatic assembly robot. The bond characteristics of CFRP rods with different pitch of helical wrapping were analyzed experimentally. As the result, all types of CFRP rods show a high initial stiffness and good ductility. The mechanical properties of helical wrapping of the CFRP rods have an important effect on the bond of these rods to concrete after the bond stress reached the yield point. The stress-slip relationship analyzed from the pull-out test of embedded cables within concrete was linear up to maximum bond capacity. The deformation within the range of maximum force seems very low and was reached after approximately 1 mm. The average bond capacity of CF20, CF30 and CF40 was about 12.06 MPa, 12.68 MPa and 12.30 MPa, respectively. It was found that helical wrapping was sufficient to yield bond strengths comparable to that of steel bars.