• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2019년도 추계학술대회
• /
• pp.112-113
• /
• 2019

UN 산하의 국제해사기구(International Maritime Organization, IMO)는 2016년 10월 24일 열린 해양환경보호위원회 70차 회의에서 2020년부터 선박에서 사용되는 연료유에 포함된 황함유량 허용치를 기존 3.5%에서 0.5% 이하로 제한하기로 결정했다. 따라서 2020년 이후부터 전 세계를 항해하는 모든 선박은 연료유의 황 함유량을 0.5% 이하로 낮춰서 운항을 해야 한다. 지속가능한 경영을 위해서 국제적 환경규제에 대응하여 각 선사의 상황에 적합한 해결책을 강구하여야

• Journal of Biosystems Engineering
• /
• 제23권2호
• /
• pp.125-134
• /
• 1998

It seems possible, by use of vegetable oils, to solve the pollution problem caused by the exhaust gas from diesel-engine vehicles. Recently vegetable oils has received considerable attention as an alternative and clean energy source to the foreseeable depletion of world oil supplies. The objective of this study is to experimentally investigate the characteristics of exhaust emissions of a small diesel engine using light oil, rice-bran oil, heated rice-bran oil, rice-bran oil treated with ultrasonic energy. SO$_2$ emission from the pure and the treated rice-bran oils was not detected at speeds hgher than 1,800 rpm while that from the light oil was detected at all the speeds at 4/4 load. NOx emission form these vegetable oils was generally higher compared to that from the light oil for most of the test conditions. tendency opposite to that of NOx emission. The data obtained in this experiment may be applicable for the desist of small diesel engine using the alternative fuels.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.55-61
• /
• 1999

The effect of S content in welding wires on the arc stability was investigated, in the region of short circuit transfer and spray transfer. In the region of short circuit transfer, with increasing S content, average arcing time and average short circuit time were decreased. Therefore, droplet transfer frequency was increased, due to the reduction of arcing time and peak current at the moment of arc-reiginition was decreased, due to the decrease of short circuit time. In the region of spray transfer, the fluctuation degree of arc current and arc voltage became more stable, with increasing S content.

• Archives of Pharmacal Research
• /
• 제10권3호
• /
• pp.153-157
• /
• 1987

Reaction of oxazolin-5-ones 1 with p-amino-diphenylamine was resulted in the formation of the corresponding imidazoline-5-ones 2 which on treatment with sulphur afforded phenothizaines 3. Acridine derivatives 5 were obtained from acetylaminodiphenyl amines derivatives 6 on heating with AnCl$_2$ at $200^{\circ}C.$3 reacted with chloroacetyl chloride to give 7 which reacted in turn with different amines to give 8. Antibacterial activity of the obtained products was studied.

• 한국표면공학회지
• /
• 제37권4호
• /
• pp.191-195
• /
• 2004

Gallium or sulphur additions in $CuInSe_2$ were prepared using RF magnetron sputtering and pulsed laser deposition respectively. All of the observed thin films shows a chalcopyrite structure with the S and Ga addition increases the favourable (112) peak. The optical absorption coefficients were slightly decreased. The energy band gap of films could be shifted from 1.04 to 1.68 eV by adjusting the mole ratio of S/(S+Se) and Ga/(In+Ga). It is possible to obtain the optimum energy band gap by adding S or Ga solute at a certain ratio in favour of Se and In respectively. It is also necessary to control the ratio of Ga and S additions and to retain a certain portion of In and Se to provide better properties of thin films.

• 한국세라믹학회지
• /
• 제15권4호
• /
• pp.199-204
• /
• 1978

In the present investigation, refined alumina obtained from alunite locally available was used as a aluminous source to synthesize monocalcium aluminate $(CA)_3$ the major mineral constituent of alumina cement. The influence of $SiO_2$ and $Fe_2O_3$ contents on the formation of monocalcium aluminate was studied by X-ray diffraction analysis mainly. About 0.8-1.0 of $Al_2O_3/C_3O$ mol ratio and less than 4 percent of $SiO_2$ were desirable for the effective formation of CA. The small amount of alkali and sulphur contents contained in refined alumina from alunite as the impurities were affected to form $C_4A_3S$ and $C_3S_2$, disadvantageous compounds for the alumina cement, therefore the impurities should be restricted in minimum content as possible.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1999-2001
• /
• 2000

Impulse breakdown voltage characteristics of sulphur-hexafluoride/nitrogen ($SF_{6}-N_{2}$) mixtures were presented. The applied voltages were the positive and negative lightning impulse (1.2/44${\mu}s$) and oscillating impulse ($0.4{\mu}s$/2.08MHz) voltages. The predischarge current was observed to clarify the breakdown mechanism. The electrode system was consisted of plane to plane configuration with a needle-shaped protrusion whose length and diameter are 10mm and 1mm. The measurements were carried out at the gas pressure of mixtures up to 0.5MPa with nitrogen concentrations varying from 5 to 20%. The electrical breakdown in $SF_{6}-N_{2}$ mixtures develops with steplike pulses in leader mechanism. The minimum breakdown voltages for the negative lightning and oscillating impulse voltages were higher than those for the positive.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1998년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Spring 1998
• /
• pp.136-143
• /
• 1998

Elastomeric bearing is used as one of the most useful way for isolation structures, because the horizontal stiffness is much lower than the vertical stiffness. The quality of Elastomeric bearing depends on the vulcanization procedure to manufacture, which produces the elasticity of the rubber from the compound of rubber and sulphur. The durability of Elastomeric bearing is affected by the deterioration due to ozone and ultra-violet attack. but the durability during the design life of bridges can be assured by the sufficient size of the bearing in spite of the deterioration in surface. In the design criteria of Elastomeric bearing, the stability of the bearings is evaluated by shear strain due to compression, lateral displacement, and rotation. The question how soft rubber can sustain heavy structure is now able to be solved by Ultimate capacity test of Laminated elastomeric Bearings, which results 1,200kg/$\textrm{cm}^2$ of the max. compressive stress and this shows what a sufficient safety factor Elastomeric bearing has!

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.208-208
• /
• 2017

• Advances in concrete construction
• /
• 제4권4호
• /
• pp.243-261
• /
• 2016

This research study focuses on utilizing sandstone which is overburden waste rock in coal mines to use in concrete as a replacement of fine aggregate. Physical properties of sandstone like water absorption, moisture content, fineness modulus etc., were found to be similar to conventional fine aggregate. Scanning Electron Microscope (SEM) analysis was carried out for analysing elemental composition of sandstone. There was no sulphur content in sandstone which is a good sign to carry the replacement. Fine aggregate was replaced with sandstone at 25%, 50%, 75% and 100% by volume and moulds of concrete cubes and cylinders were prepared. Compressive strength of concrete cubes was tested after 3, 7 and 28 days and split tensile & flexural strength was determined after 28 days. The strength was found to be increasing marginally with increase in sandstone content. Fine aggregate that was replaced by 100% sandstone gave highest strength among all the replacements for the compressive, split tensile and flexural strengths. Though increase in strength was marginal, still sandstone can be an effective replacement for sand in order to save the natural resource and utilize the waste sandstone.