• Korean Journal of Metals and Materials
• /
• v.48 no.10
• /
• pp.901-906
• /
• 2010

The first stage blade of a gas turbine was operated under a severe environment which included both $1300^{\circ}C$ hot gas and thermal stress. To obtain high efficiency, a thermal barrier coating (TBC) and an internal cooling system were used to increase the firing temperature. The TBC consists of multi-layer coatings of a ceramic outer layer (top coating) and a metallic inner layer (bond coat) between the ceramic and the substrate. The top and bond coating layer respectively act as a thermal barrier against hot gas and a buffer against the thermal stress caused by the difference in the thermal expansion coefficient between the ceramic and the substrate. Particularly, the bondcoating layer improves the resistance against oxidation and corrosion. An inter-diffusion layer is generated between the bond coat and the substrate due to the exposure at a high temperature and the diffusion phenomenon. A thickness measurement result showed that the bond coat of the suction side was thicker than that of the pressure side. The thickest inter-diffusion zone was noted at SS1 (Suction Side point 1). A chemical composition analysis of the bond coat showed aluminum depletion around the inter-diffusion layer. In this study, we evaluated the properties of the bond coat and the degradation of the coating layer used on a $1300^{\circ}C$-class gas turbine blade. Moreover, the operation temperature of the blade was estimated using the Arrhenius equation and this was compared with the result of a thermal analysis.

• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.331-336
• /
• 2015

We report on the succesful fabrication of ZnO nanorod (NR)-based robust piezoelectric nanogenerators (PNGs) by using Cu foil substrate. The ZnO NRs are successfully grown on the Cu foil substrate by using all solution based method, a two step hydrothermal synthesis. The ZnO NRs are grown along c-axis well with an average diameter of 75~80 nm and length of $1{\sim}1.5{\mu}m$. The ZnO NRs showed abnormal photoluminescence specrta which is attributed from surface plasmon resonance assistant enhancement at specific wavelength. The PNGs on the SUS substrates show typical piezoelectric output performance which showing a frequency dependent voltage enhancement and polarity dependent charging and discharging characteristics. The output voltage range is 0.79~2.28 V with variation of input strain frequency of 1.8~3.9 Hz. The PNG on Cu foil shows reliable output performance even at the operation over 200 times without showing degradation of output voltage. The current output from the PNG is $0.7{\mu}A/cm^2$ which is a typical out-put range from the ZnO NR-based PNGs. These performance enhancement is attributed from the high flexibility, high electrical conductivity and excellent heat dissipation properties of the Cu foil as a substrate.

• Microbiology and Biotechnology Letters
• /
• v.24 no.5
• /
• pp.597-603
• /
• 1996

This study was carried out to examine degradation characteristics of microalgae Chlorella vulgaris in methane fermentation. We measured COD and VS reduction, gas and methane productivity, VFA (volatile fatty acid), respectively. Then we calculated material balance and hydrolysis rates in soluble and solid material. The substrate concentration was controlled from 14 gCOD$_{cr}$/l to 64 gCOD$_{cr}$/l in batch cultures, and HRT (hydraulic retention time) controlled from 2 days to 30 days in continuous experi- ments. The results were as follows. In batch culture, accumulated gas productivity increased with the increase of the substrate concentration. The SS and VSS was removed all about 30% increase of substrate concentration and the most of the degradable material removed during the first 10 days. The curve of gas and methane production rate straightly increased until substrate concentration is 26 gCOD$_{cr}$/l. In continuous culture experiments, the removal rates at HRT 10days were 20% for total COD and TOC, respectively. At longer HRT, there was no increase in the removal efficiency. At HRT 15 days, the removal rates were 30% for SS and VSS, respectively. Soluble organic materials were rapidly degraded, and so there was no accumulated. Soluble COD concentration was not increase regardless of HRT-increasing. That meaned the hydrolysis was one of the rate-limiting stage of methane fermentation. The first-order rate constants of hydrolysis were 0.23-0.28 day$^{-1}$ for VSS, and 0.07-0.08 day$^{-1}$ for COD.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.393-398
• /
• 1996

Soft magnetic properties and microstructural evolution of FeTaNC films were investigated, and compared with FeTaN and FeTaC films. Effects of substrate species (glass vs. $CaTiO_3$) on the magnetic properties were also investigated. Co-addition of N and C significantly enhance the grain refinments and magnetism, compared with N or C addition only. Good soft magnetic characteristics of coercivity of 0.17 Oe, permeability of 4000 (5MHz), and saturation flux density of 17 kG can be obtained in the FeTaNC in the relatively wide process windows. While these values appears to be similar to those of FeTaN on glass substrate, most distinctive difference between FeTaNC and FeTaN(or C) is in the effects of substrate. Whereas FeTaNC films show good magnetic characteristics for both glass and $CaTiO_3$ substrates, FeTaN(or C) films show significant degradation on the $CaTiO_3$ substrate.

• Korean Journal of Materials Research
• /
• v.24 no.6
• /
• pp.305-309
• /
• 2014

When sunlight irradiates a boron-doped p-type solar cell, the formation of BsO2i decreases the power-conversion efficiency in a phenomenon named light-induced degradation (LID). In this study, we used boron-doped p-type Cz-Si solar cells to monitor this degradation process in relation to irradiation wavelength, intensity and duration of the light source, and investigated the reliability of the LID effects, as well. When halogen light irradiated a substrate, the LID rate increased more rapidly than for irradiation with xenon light. For different intensities of halogen light (e.g., 1 SUN and 0.1 SUN), a lower-limit value of LID showed a similar trend in each case; however, the rate reached at the intensity of 0.1 SUN was three times slower than that at 1 SUN. Open-circuit voltage increased with increasing duration of irradiation because the defect-formation rate of LID was slow. Therefore, we suppose that sufficient time is needed to increase LID defects. After a recovery process to restore the initial value, the lower-limit open-circuit voltage exhibited during the re-degradation process showed a trend similar to that in the first degradation process. We suggest that the proportion of the LID in boron-doped p-type Cz-Si solar cells has high correlation with the normalized defect concentrations (NDC) of BsO2i. This can be calculated using the extracted minority-carrier diffusion-length with internal quantum efficiency (IQE) analysis.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.10
• /
• pp.1440-1445
• /
• 2010

Rhodococcus sp. JDC-11, capable of utilizing di-n-butyl phthalate (DBP) as the sole source of carbon and energy, was isolated from sewage sludge and confirmed mainly based on 16S rRNA gene sequence analysis. The optimum pH, temperature, and agitation rate for DBP degradation by Rhodococcus sp. JDC-11 were 8.0, $30^{\circ}C$, and 175 rpm, respectively. In addition, low concentrations of glucose were found to inhibit the degradation of DBP, whereas high concentrations of glucose increased its degradation. Meanwhile, a substrate utilization test showed that JDC-11 was also able to utilize other phthalates. The major metabolites of DBP degradation were identified as monobutyl phthalate and phthalic acid by gas chromatography-mass spectrometry, allowing speculation on the tentative metabolic pathway of DBP degradation by Rhodococcus sp. JDC-11. Using a set of new degenerate primers, a partial sequence of the 3,4-phthalate dioxygenase gene was obtained from JDC-11. Moreover, a sequence analysis revealed that the phthalate dioxygenase gene of JDC-11 was highly homologous to the large subunit of the phthalate dioxygenase from Rhodococcus coprophilus strain G9.

• Proceedings of the Korean Biophysical Society Conference
• /
• 2003.06a
• /
• pp.34-34
• /
• 2003

Protein unfolding is a key step in several cellular processes, including protein translocation across some membranes and protein degradation by ATP-dependent proteases. C1pAP protease and the proteasome can actively unfold proteins in a process that hydrolyzes ATP, These proteases catalyze unfolding by processively unraveling their substrates from the attachment point of the degradation signal. As a consequence, the ability of a protein to be degraded depends on its structure as well as its stability. An ${\alpha}$-helix is easier to unravel than a ${\beta}$-strand. In multidomain proteins, independently stable domains are unfolded sequentially. The steric constraints imposed on substrate proteins during their degradation by the proteasome were investigated by constructing a model protein in which specific parts of the polypeptide chain were covalently connected through disulfide bridges. The cross-linked model proteins were fully degraded by the proteasome, but two or more cross-links retarded the degradation slightly. Our results suggest that the pore of the proteasome allows the concurrent passage of at least three stretches of a polypeptide chain, and also explain the limited degradation by the proteasome that occurs in the processing of the transcription factor NF-KB, and also implicate difficulty in degradation of amyloidal aggregates by the proteasome

• Corrosion Science and Technology
• /
• v.6 no.5
• /
• pp.261-268
• /
• 2007

Embedded sensors were used as an in-situcorrosion-sensing device for aircraft and vehicular structures protected by organic coatings. Results are presented changes associated with a standard Airforce aircraft coating and a standard Army vehicle coating were monitored by embedded sensors. These coatings consisted of a polyurethane topcoat and an epoxy primer, however are formulated to provide different characteristics. The ac-dc-ac testing method was used to accelerate the degradation of these coatings while being immersed in a NaCl medium. Electrochemical impedance spectroscopy and electrochemical noise measurement experiments were used to monitor the induced changes. A comparison of the results between coatings subjected to the ac-dc-ac exposure and coatings subjected to only constant immersion in the NaCl medium is presented. The results were used to demonstrate the effectiveness of the ac-dc-ac method at accelerating the degradation of an organic coating without observably changing the normal mechanism of degradation. The data highlights the different features of the coating systems and tracks them while the coating is being degraded. The aircraft coating was characterized by a high-resistant topcoat that can mask corrosion/primer degradation at the primer/substrate interface whereas the vehicle coating was characterized by a low-resistant topcoat with an effective corrosion inhibiting primer. Details of the ac-dc-ac degradation were evaluated by using an equivalent circuit to help interpret the electrochemical impedance data.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.100-104
• /
• 2008

Titanium sheet metal substrates used in thin film batteries were wet etched and their surface area was increased in order to increase the discharge capacity and power density of the batteries. To obtain a homogeneous etching pattern, we used a conventional photolithographic process. Homogeneous hemisphere-shaped wells with a diameter of approximately $40\;{\mu}m$ were formed on the surface of the Ti substrate using a photo-etching process with a $20\;{\mu}m{\times}20\;{\mu}m$ square patterned photo mask. All-solid-state thin film cells composed of a Li/Lithium phosphorous oxynitride (Lipon)/$LiCoO_2$ system were fabricated onto the wet etched substrate using a physical vapor deposition method and their performances were compared with those of the cells on a bare substrate. It was found that the discharge capacity of the cells fabricated on wet etched Ti substrate increased by ca. 25% compared to that of the cell fabricated on bare one. High discharge rate was also able to be obtained through the reduction in the internal resistance. However, the cells fabricated on the wet etched substrate exhibited a higher degradation rate with charge-discharge cycling due to the nonuniform step coverage of the thin films, while the cells on the bare substrate demonstrated a good cycling performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.110-120
• /
• 2010

In this paper, we propose a tunable SIW(Substrate Integrated Waveguide) using dielectric screws for eliminating the phase imbalance of large size power distribution networks(PDN). Alumina screws partially inserted into several through holes of the tunable SIW section effectively change the phase shift without S-parameter degradation. ${\pm}33.9^{\circ}$ measured phase imbalance of a large conventional 9 GHz SIW-PDN of $370\;mm{\times}195\;mm$ size has been greatly reduced to ${\pm}4.65^{\circ}$. We expect that the proposed tunable SIW plays an important role for a light-weight, high performance substrate integrated phased array system(Si-PAS) and large size SIW circuit applications.