• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.61-69
• /
• 2000

Indium-Tin Oxide (ITO) films were prepared on the commercial glass substrate by the Magnetron Sputtering method. The target was a 90wt.% $In_2O_3$-10wt.% $SnO_2$with 99.99% purity. The ITO films deposited by changing the partial pressure of oxygen gas ($O_2$/(Ar+$O_2$)) of 2, 3 and 5% as well as by changing the substrate temperature of $300^{\circ}C$ or $500^{\circ}C$. The influence of substrate pre-annealing and pre-cleaning on the quality of ITO film were examined, in which the substrate temperature was $500^{\circ}C$ and oxygen partial pressure was 3%. The characteristics of films were examined by the 4-point probe, Hall effect measurement system, SEM, AFM, Spectrophotometer, and X-ray diffraction. The optimum ITO films have been obtained when the substrate temperature is $500^{\circ}C$ and oxygen partial pressure is 3%. At optimum condition, the film showed transmittance of 81%, sheet resistivity of $226\Omegatextrm{cm}^2$, resistivity($\rho$) of $5.4\times10^{-3}\Omega$cm, carrier concentration of $1.0\times10^{19}cm^{-3}$, and carrier mobility of $150textrm{cm}^2$Vsec. From XRD spectrum, c(222) plane was dominant in the case of substrate temperature at $300^{\circ}C$, without regarding to oxygen partial pressure. However, in the case of substrate temperature at $500^{\circ}C$, c(400) plane was grown together with c(222) plane, only for oxygen partial pressure of 2 and 3%. In both case of chemical and ultrasonic cleaning without pre-annealing the substrate, it showed much almost same sheet resistivity, resistivity($\rho$), transmittance, carrier concentration, and carrier mobility. In case of $500^{\circ}C$/60min pre-annealing before ITO film deposited, both transimittance and carrier mobility are better than no pre-annealing, because pre-annealing is supposed to remove alkari ions diffusion from substrate. ITO film deposited on the Corning 0080 sybstrate showed a little bit better sheet resistivity, resistivity($\rho$), transimittance, carrier concentration than the film deposited on commercial glass. But no differences between Corning substrate and pre-annealed commercial glass substrate are found.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1999.10a
• /
• pp.19-22
• /
• 1999

A microbial consortium derived from a gasoline-contaminated sites was enriched on toluene in 100-mL serum bottle and was found to degrade benzene(B), toluene(T), ethylbenzene(EB), and xylenes(X). Studies conducted to determine the temperature effects and BTEX concentration on BTEX degradation. The results indicated that lowering temperature significantly decreased BTEX degradation rates and varing the BTEX concentration also changed substrate degradation patterns.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.1
• /
• pp.92-99
• /
• 1994

Diamond thin film was deposited on n type (100) Si substrate by MPECVD(Microwave plasma Enhanced Chemical Vapor Deposition). For the increase in nucleation density of diamond, Si substrate was pretreated by diamond powder or negative bias voltage was applied to the substrate during the initial deposition. In the case of retreated Si substrate, the diamond thin film quality was enhanced with increasing the total pressure in the range of 20~150 Torr. For the negative bias voltage, the formation condition of the diamond was seriously affected by $CH_4$ concentration and total pressure. The formation condition will be discussed with electrical current of substrate generated by plasma ions which depend on $CH_4$concentration, bias voltage, and total pressure.

• Journal of Microbiology and Biotechnology
• /
• v.13 no.1
• /
• pp.57-63
• /
• 2003

Using fungal (Fusarium solani f. pisi) and bacterial (Pseudomonas mendocina) cutinases, the initial hydrolysis rate of p-nitrophenyl esters was systematically estimated for a wide range of enzyme and substrate concentrations using a 96-well microplate reader. Both cutinases exhibited a high substrate specificity; i.e. a high hydrolytic activity on p-nitrophenyl butyrate (PNB), yet extremely low activity on p-nitrophenyl palmitate (PNP). When compared to the hydrolysis of PNB and PNP by other hydrolases [lipases and esterases derived from different microbial sources, such as bacteria (Pseudomonas cepacia, Psedomonas furescens, Baciilus stearothermophilus), molds (Aspeillus niger, mucor miehei), and yeasts (Candida rugosa, Candida cylindracea)], the above substrate specificity would seem to be a unique characteristic of cutinases. Secondly, the hydrolytic activity of the cutinases on PNB appeared much faster than that of the other hydrolytic enzymes mentioned above. Furthermore, the current study proved that even when the cutinases were mixed with large amounts of other hydrolases (lipases or esterases), the Initial hydrolysis rate of PNB was determined only by the cutinase concentration for each PNB concentration. This property of cutinase activity would seem to result from a higher accessibility to the substrate PNB, compared with the other hydrolytic enzymes. Accordingly, these distinct properties of cutinases may be very useful in the rapid and easy isolation of various natural cutinases with different microbial sources, each of which may provide a novel industrial application with a specific enzymatic function.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.2
• /
• pp.17-21
• /
• 2004

Aluminum nitride(AlN) thin films were deposited on silicon substrate by reactive RF magnetron sputtering without substrate heating. We investigated the dependence of some properties for AlN thin film on sputtering conditions such as working pressure, $N_2$ concentration and RF power. XRD, Ellipsometer and AES has been measured to find out structural properties and preferred orientation of AlN thin films. Deposition rate of AlN thin film was increased with an increase of RF power and decreased with an increase of $N_2$ concentration. AES in-depth measurements showed that stoichiometry of Aluminium and Nitrogen elements were not affected by $N_2$ concentration. It has shown that low working pressure, low $N_2$ concentration and high RF power should be maintained to deposit AlN thin film with a high degree of (0002) preferred orientation.

• Korean Journal of Microbiology
• /
• v.20 no.2
• /
• pp.67-72
• /
• 1982

The effect of fermentation temperature on the production of high content alcohol has been investigated with high substrate concentration. The maximum specific growth rate, ${\mu}max\;was\;0.461hr^{-1}\;at\;35^{\circ}C$ which was the highest, whereas the maximum biomass concentration waas 8.7g/l at $25^{\circ}C$, at the growth rate lower than at $35^{\circ}C$. Approximately 140g/l of ethanol was produced in the temperature range of 20 to $25^{\circ}C$ with nearly complete comsumption of the substrate. Extended fermentation time has been required at lower temperatures, however, for the maximum values of biomass concentration and alcohol content, hence higher ethanol productivity, as the temperature was elevated to $40^{\circ}C$. The viability of yeasts was greatly improved by lowering the fermentation temperature down to $25^{\circ}C$ and also extended survival of the cells has been observed at lower fermentation temperatures, although the ethanol concentration of both waas higher.

• Journal of agriculture & life science
• /
• v.44 no.6
• /
• pp.9-14
• /
• 2010

The present study was performed to identify the possibility of the disused paper-sludge to substitute an substrate for nursery plants. Tosilee substrate as control, paper-sludge and tosilee substrate (1:1, v:v), and paper sludge substate were used in this experiment. After harvesting tomato seedlings, there were no significant differences in growth parameters such as plant height, root length, and fresh and dry weight grown for tosilee substrate, and paper-sludge and tosilee mixture substrate. However, the seedlings grown for paper-sludge substrate alone were extremely depressed. These growth pattern was followed by cucumber seedlings. As the result of this experiment, we suggest that it must need to stabilize the pH and EC, and Zn concentration in paper-sludge for increasing its material for substrate.

• Journal of Bio-Environment Control
• /
• v.4 no.1
• /
• pp.25-31
• /
• 1995

This study was carried out to investigate the effect of the concentration of nutrient solution on the growth of tomato(Lycopersicon esculentum Mill. cv. seokwang) in substrate culture. The substrates used in the experiment were perlite, vermiculite, and peatmoss. Tomato plants were treated with different concentrations of nutrient solution, viz. 0.5, 1.0, 2.0, 3.0, and 5.0mS/cm at seedling stage and transferred to different treatments, 1.0, 2.0, and 3.0mS/cm after transplanting in each substrate. As the concentrations of nutrient solution increased from 0.5 to 3.0mS/cm at seedling stage, the $CO_2$ assimilation rates of seedlings increased in all three substrate culture. Beyond this range, the $CO_2$ assimilation rates of seedlings decreased. By increasing the concentrations of nutrient solution, plant height, leaf length, leaf width, stem diameter, and top dry weight increased in perlite and were high at 2-5mS/cm in vermiculite. On the other hand, in peatmoss, the best result was shown at 3.0mS/cm. Therefore, the adequate concentration of nutrient solution on early growth of seedlings differed among substrates and was shown to be 3.0-5.0mS/cm in perlite, 2.0-5.0mS/cm in vermiculite, and 3.0mS/cm in peatmoss. Generally, as the concentrations of nutrient solution increased from 1.0 to 3.0mS/cm after transplanting, dry weight increased significantly in all three substrate culture. However, dry weights of tomato plants grown under high concentration of 5.0mS/cm slightly increased both at seedling stage and after transplanting.

• Journal of Environmental Science International
• /
• v.30 no.8
• /
• pp.605-612
• /
• 2021

Supply electrical conductivity (EC) concentration of the nutrition solution is an important factor in the absorption of nutrients by plants and the management of the root zone, as it can control the vegetative/reproductive growth of a plant. Paprika usually undergoes its reproductive and vegetative growth simultaneously. Therefore, ensuring proper growth of the plant leads to increased yield of paprika. In this study, growth characteristics of paprika were examined according to the EC concentration of a coir and a rockwool substrate. The supply EC was 1.0, 2.0, and 4.0 mS·cm^-1 applied at the initial stages of the growth using the rockwool (commonly used by paprika farmers) and the coir substrate with a chip and dust ratio of 50:50 and 70:30. For up to 16 weeks of paprika growth, EC concentrations of 1.0 and 2.0 mS·cm^-1 were found to have a greater effect on the growth than EC at 4.0 mS·cm^-1. The normality (marketable) rate of fruit, the soluble solid content, and paprika growth showed that the coir was generally better than the rockwool regardless of the supply EC concentration. The values of the yield per plant at an EC concentration of 4.0 mS·cm^-1 was mostly similar at 1.6 kg (coir 50:50), 1.5 kg (coir 70:30) and 1.5 kg (rockwool), but the yield of the rockwool was 88%, which was lower than 98% and 94% yield of the coir substrate. Therefore, this concludes that coir substrate is more effective than rockwool at improving paprika productivity. The results also suggest that the use of coir substrate for paprika has many benefits in terms of reducing production costs and preventing environmental destruction during post-processing.

• Journal of Surface Science and Engineering
• /
• v.49 no.2
• /
• pp.119-124
• /
• 2016

Plasma electrolytic oxidation (PEO) is a promising coating process to produce ceramic oxide on valve metals such as Al, Mg and Ti. The PEO coating is carried out with a dilute alkaline electrolyte solution using a similar technique to conventional anodizing. The coating process involves multiple process parameters which can influence the surface properties of the resultant coating, including power mode, electrolyte solution, substrate, and process time. In this study, ceramic oxide coatings were prepared on commercial Al alloy in electrolytes with different KOH concentrations (0.5 ~ 4 g/L) by plasma electrolytic oxidation. Microstructural and electrochemical characterization were conducted to investigate the effects of electrolyte concentration on the microstructure and electrochemical characteristics of PEO coating. It was revealed that KOH concentration exert a great influence not only on voltage-time responses during PEO process but also on surface morphology of the coating. In the voltage-time response, the dielectric breakdown voltage tended to decrease with increasing KOH concentration, possibly due to difference in solution conductivity. The surface morphology was pancake-like with lower KOH concentration, while a mixed form of reticulate and pancake structures was observed for higher KOH concentration. The KOH concentration was found to have little effect on the electrochemical characteristics of coating, although PEO treatment improved the corrosion resistance of the substrate material significantly.