• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.284-290
• /
• 1993

The soap-free emulsion polymerization was carried out for Styrene/Butadiene system with Acrylonitrile as hydrophilic comonomer and KPS as initiator. Under the condition of below 50% conversion, the dependence of Rp on $[AN]^n$ and $[KPS]^n$ was found to be n=1.617-1.050 and n=0.83-0.96 for [AN] and [KPS], respectively. The effect of $[AN]^n$ and $[KPS]^n$ on particle number density (Np) was determined to be n=1.533 and n=0.733, respectively. The highest conversion was obtained under the conditions of pH=5 and ratio of total monomer (g) to water (g)=0.5. The mechanical properties of SBR obtained in this experiment were shown to be inferior to commercial SBR in terms of tensile strength, 300% modulus and elongation. It was found that cure rate of SBR prepared in this experiment was faster than that of commercial SBR.

• Membrane Journal
• /
• v.20 no.2
• /
• pp.142-150
• /
• 2010

A series of anion exchange composite membranes were prepared and characterized for electrodialysis processes used in the removal of nitrate nitrogen and ions in groundwater. The membranes were prepared as follows; first, fabric substrates were fully impregnated with monomer mixtures of vinylbenzylchloride (VBC), divinylbenzene (DVB), Styrene (ST) and $\alpha,\alpha$-Azobis(isobutyronitrile) (AIBN). Second, they were thermally polymerized to yield crosslinked poly (VBCST- DVB)/fabric composite membranes. Finally, the membranes were treated with trimethylamine (TMA) / acetone to give $-N^+(CH_3)_3^-$-containing poly(VBC-ST-DVB)/fabric membranes. The basic membrane properties such as ion exchange capacity (IEC), electric resistance and water content of the resulting membranes were measured as a function of VBC/DVB and TMA/Acetone content. As a result, the composite membranes showed lower electric resistance and higher IEC than commercial anion exchange membranes (AMX, Astom). Electrodialysis tests using the prepared membranes were carried out for the removal of various ions such as $NaNO_3$, $MgSO_4$ and NaF for 60 minutes. The results showed that the ions were removed below 1 mg/L within about 15 minutes which indicates that the anion exchange membranes prepared here could be applied to the electrodialysis process. as can be seen in the following that the ion conductivity values were almost no change after 15 minutes electrodialysis.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.715-722
• /
• 1995

Vinylbenzyl triphenyl phosphonium chloride (VTPC) was prepared for the humid membrane. The humidity sensitive memo)lane was composed of copolymers, which have differnet content of VTPC and styrene (VTPC : ST=1 : 0.7 : 3, 5 : 5, 3 : 7). The changes in electrical properties of copolymers with relative humidity were measured. It was found that the impedance decreased with an increase of the content of VTPC in the humid membrane, and the Impedance also decreased with an increase of thickness of humid membrane. The copolymer derived from same equip of VTPC and ST showed 12M$\Omega$-100M$\Omega$ at 70%RH-90%RH, which was required for the current humidity sensor operating at high humidity or dew point. The temperature dependence coefficient at a temperature range 15$^{\circ}C$∼35$^{\circ}C$ was found to be -0.5%RH/$^{\circ}C$ and the hysterisis fabled within the range ${\pm}$2%RH. The response time was found to be 40seconds for varing relative humidity from 75% RH to 95%RH and vice versa.

• Elastomers and Composites
• /
• v.37 no.1
• /
• pp.21-30
• /
• 2002

Core-shell polymers of methyl methacrylate/styrene pair were prepared by sequential emulsion polymerization in the presence of sodium dodecyl benzene sulfonate(SDBS) as an emulsifier using ammonium persulfate(APS) as an initiator. The characteristics of these core-shell polymers were evaluated. Core-shell composite latex has the both properties of core and shell components in a particle, where as polymer blonds or copolymers show a combined properties from the physical properties or two homopolymers. This unique behavior of core-shell composite latex can be used in many industrial fields. However, in preparation of core-shell composite latex, several unexpected phenomina are observed, such as, particle coagulation, low degree of polymerization, and formation of new particles during shell polymerization. To solve the disadvantages, we studied the effects of surfactant concentrations, initiator concentrations, and reaction temperature on the tore-shell structure or PMMA/PSt and PSt/PMMA. Particle size and particle size distribution were measured by using particle size analyzer, and the morphology of the core-shell composite latex was observed by using transmission electron microscope. Glass transition temperature($T_g$) was also measured by using differential scanning calorimeter. To identify the core-shell structure, pH of the composite latex solutions were measured.

• Macromolecular Research
• /
• v.17 no.12
• /
• pp.1003-1009
• /
• 2009

Copolymers of N-vinylpyrrolidone (NVP) comonomer with styrene (St), hydroxypropyl methacrylate (HPMA) and carboxyphenyl maleimide (CPMI) were synthesized by free radical polymerization using 2,2'-azobisisobutyronitrile (AIBN) initiator in 1,4-dioxane solvent. The copolymers formed were characterized by FTIR, $^1H$ NMR and $^{13}C$ NMR techniques and their thermal properties were studied by DSC and TGA. Copolymer composition was determined by $^1H$ NMR and/or by elemental analysis and monomer reactivity ratios (MRR) were estimated by the linear methods of Kelen-Tudos (K-T) and extended Kelen-Tudos (EK-T) and the non-linear approach. Copolymers of St and HPMA with NVP formed blocks of one of the monomer units, whereas alternating copolymers were obtained in CPMI-NVP, depending upon the side chain substitution. The MRR values are discussed in terms of monomer structural properties such as electronegativity and electron delocalization. The sequence distribution of monomers in the copolymers was studied by statistical method based on the average reactivity ratios obtained by EK-T method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.35-38
• /
• 2003

The purpose of this study is to investigate the manufacture of light weight concrete panel using the artificial light-weight aggregate as a part of the substitution of foamed styrene and polyurethane because of narrow allocable temperature Bone in use. The experimental parameter of this study is 40, 60 and 8$0^{\circ}C$ of curing temperature at 100% relative humidity and the type of admixture such as cement, 6mm glass fiber and St/BA emulsion. Testing item is compressive and flexural strength and strength of specimen cured at standard condition is compared to that of specimen cured at 40, 60 and 8$0^{\circ}C$ of curing temperature at 100% relative humidity. As a result or this, it was revealed that the maximum or strength is developed in 6$0^{\circ}C$ or cure temperature at 100% relative humidity in case of the most of the specimen. Specimens modified by St/BA emulsion show the highest development of strength dependent on the curing tmeperature. So, it seems to be effective that evaporation curing method shoud be considered to curing the specimen as the panel core.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.279-286
• /
• 2002

Linear and nonlinear complex permittivities were measured for copolymers of vinylidene cyanide(VDCN) with vinyl acetate(VAc), vinyl propionate(VPr), vinyl bezoate(VBz), styrene(St) and methyl methacrylate(MMA). Experimental results are well fitted by the function (equation omitted) except at low frequency where dc conduction dominates. The analysis of dielectric relaxation mechanism by combined knowledge about linear and nonlinear dielectric permittivities and dipoles give us informations about electrical and thermal motions in these copolymers. According to the analysis it could be found that the variation for temperature of the dielectric relaxation strength in these copolymers is related to the interaction between dipoles and the nonlinear dielectric effect factor R$_{s}$ is proportional to square of the dipolar correlation factor R$_{p}$././.

• Macromolecular Research
• /
• v.11 no.4
• /
• pp.273-282
• /
• 2003

A hydrophilic macromolecular network containing hydrophobic moieties has been prepared by free radical copolymerization of acrylamide and styrene in the presence of poly(vinyl alcohol) (PVA) and its potential as controlled drug delivery carrier was evaluated with tetracycline as a model antibiotic drug. The amount of drug was assayed spectrophotometrically. The network was characterized by optical microscopy, infra-red spectroscopy and structural parameters such as average molecular weight between cross1inks ($M_c$), cross1ink density (q) and number of elastically effective chains ($V_e$) were evaluated. It was found that with increasing concentration of PVA, ST and MBA in the hydrogel, the release rate initially increases but after definite concentrations of the above components the release rate falls. In the case of AM, release rate constantly decreases with increasing AM concentration in the hydrogel.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.81-92
• /
• 2016

1,3-Diphenylguanidine (DPG) is commonly used as a secondary accelerator which not only acts as booster of cure but also activating silanization reaction. The aim of this study is to increase the interaction between silica and rubber by using DPG. In this study, mixing was proceeded in two steps. The T-1 compound is mixed DPG with silica and silane coupling agent in the kneader at high temperature which is named as $1^{st}$ mixing step. T-3 compound is mixed DPG with curatives in the two-roll mill at low temperature which is named as $2^{nd}$ mixing step. The T-2 compound is mixed a half of DPG in $1^{st}$ mixing step and the remainder is mixed in $2^{nd}$ mixing step. Total DPG content was equal for all compounds. When DPG is mixed with silica, silane coupling agent during the $1^{st}$ mixing step, a decrease in cure rate and an increase in scorch time can be seen. This indicates that DPG is adsorbed on the surface of silica. during rubber processing. However, bound rubber content is increased and dynamic properties are improved. These results are due to the highly accelerated silanization reaction. However, there are no significant difference in 100%, 300% modulus.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.617-624
• /
• 2001

The core-shell composite latexes were synthesized by stage emulsion polymerization of methyl methacrylate (MMA) and styrene (St) with ammonium persulfate after preparing monomer pre-emulsion in the presence of anionic surfactant. However, in preparation of core-shell composite latex, several unexpected results are observed, such as, particle coagulation, low degree of polymerization, and formation of new particles during shell polymerization. To solve the disadvantages, We study the effect of initiator concentrations, surfactant concentrations, and reaction temperature on the core-shell structure of polymethyl methacrylate/polystyrene and polystyrene/polymethyl methacrylate. Particle size and particle size distribution were measured using particle size analyzer, and the morphology of the core-shell composite latex was determined using transmission electron microscope. Glass temperature was also measured using differential scanning calorimeter. To identify the core-shell structure, pH of the two composite latex solutions were measured.