• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.306-315
• /
• 2010

The stress laminated timber, which could be manufactured by small dimension lumber on construction site, has high possibilities for bridges in remote area, such as recreation forest or forest road, because those bridges may be short span and low frequency in use. The stress laminated timber has merits of easiness for preservative treatment and transportation because it is manufactured with small dimension lumber. This study was carried out to analyze performances of stress laminated timber manufactured with preservative treated domestic pitch pine for developing structural design data for stress laminated timber bridges for vehicular traffic. Perpendicular to grain compressive performance by preservative treatment and bending performance by bored holes of pitch pine lumber was analyzed. Then, the effects of bending performance by pre-stress pressure, distance of bolts, number of laminations and planning were analyzed. Conclusively, planning of lumber was not necessary for manufacturing stress laminated timber, and 80% of bending stiffness criteria was maintained as pre-stress pressure was higher than 3.0 kg/$cm^2$. However, further researches are needed to define the effects of bolt distances and number of laminations. The results of this research would be basic data for design stress laminated timber bridges for vehicular traffic in Korea.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.85-92
• /
• 2018

In order to use glued built up timber beam as a structural member for post and beam construction, it must be possible to manufacture long-span lumber. In this study, the researchers conducted a performance evaluation for longitudinal bonding of lumber (cross-section $89{\times}120mm$) made from larch. The specimens were prepared in six different forms using the longitudinal bonding method. The bonding strength of these specimens was tested through tensile strength tests and bending strength tests. The tensile strength test result of the longitudinally bonded parts was better than that of the double lap specimens. And, the tensile strength value of the scarf specimen was better than that of the hooked scarf specimen. The tensile strength of the GFRP (Glass Fiber Reinforced Plastic) rod insertion bonding specimen was 3.6 MPa, which was the highest. As for the bending strength test result of the longitudinally bonded part, the average MOR (modulus of rupture) of the specimen where a GFRP rod was inserted and bonded measured 29 MPa, while the specimens of other bonded parts showed a MOR no more than 11 MPa. Toughness destruction was observed in specimens where a GFRP rod was insertion-bonded. The rest of the specimens showed brittle destruction. The average MOR strength of the Rod + Lap specimen was 30.5 MPa, which was the highest among all longitudinally bonded specimens. The bending strength of the Rod + Lap specimens showed an effective strength that was 66% of that of the control group which were not longitudinally bonded.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.504-507
• /
• 2009

구조용 재료중에서 목재는 비중에 비하여 강도가 크고. 가공성이 우수하며, 뛰어난 미관을 가지고 있다는 장점이 있지만 다른 건축 구조재료에 비하여 연소와 부식의 우려뿐만 아니라, 쉽게 부패하고 변형이 되는 단점도 가지고 있는 것이 사실이다. 이러한 단점에 의해 생긴 심각한 결함은 건물을 붕괴할 수도 있다. 따라서, 오늘날 목재가 사용된 건축물의 경제적인 유지관리가 중요시 되고 있다. 본 연구는 이질재료와 접합된 노후화된 목재 부재의 성능을 분석하여 쉽게 부패하고 변형이 되는 목재의 효율적인 유지관리방향의 기초를 확립하고자 하는 것을 목표로 하고 있다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.3
• /
• pp.271-280
• /
• 2003

The purpose of the study presented in this paper is to develope the general model for capture of the linear and nonlinear response of a flexible diaphragm building in which there are significant contributions from the out-of-plane walls. Two single-story single-diaphragm half scale reinforced masonry buildings were tested by researchers at the United States Army Construction Engineering Research Laboratory (CERL). The first had a metal deck diaphragm. The second specimen had a diaphragm with a single layer of diagonal lumber sheathing, A multiple degree of freedom (MDOF) approach is adopted in this paper. The required stiffnesses and strengths of the components within this model are determined.

• Journal of Korea Foresty Energy
• /
• v.22 no.2
• /
• pp.60-68
• /
• 2003

In forest products industry, a variety of nondestructive evaluation techniques are now being used to assess the mechanical properties of structural lumber. Ultrasonic and longitudinal vibration technique are frequently used to assess the modulus of elasticity(MOE) of lumber. The objective of this research was to evaluate the MOE and modulus of rupture(MOR) of small-diameter of Larix log(Larix kaempferi Carr.), using these techniques. In this study, 50 small-diameter logs were nondestructiveively evaluated. The dynamic modulus of elasticity(Eu) of the logs was first evaluated, using an ultrasonic method. After ultrasonic tests, the logs were measured using a longitudinal vibration technique(Ev). Static bending test was then performed on the logs to obtain the static modulus of elasticity(Es) and modulus of rupture of these logs. In general, the dynamic MOE (Ev) of logs was closely co..elated with the stati, MOE for log. Based on the results of these experiments, it can be concluded that small-diameter Larix logs can be successfully evaluated by Ultrasonic and longitudinal vibration technique. The experimental results indicated that the ultrasonic technique is effective to the log, which contains many knots. The longitudinal vibration technique is effective to the log, in which many cracks are included.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.2
• /
• pp.163-171
• /
• 2011

Because Japanese cedar shows lower mechanical performance, glued-laminated timber (glulam) can be a better way to utilize Japanese cedar for structural purpose. However, low yield of higher grade lamination from log makes it difficult to design structural glulam. This study was aimed to increase the yield of higher grade lamination and provide higher efficiency of manufacturing structural lamination by ultrasonic log sorting technology. Logs were sorted by an existing log grading rule regulated by Korea Forest Research Institute (KFRI). It was found that the KFRI log grading rule contributed to finding better logs in viewpoint of the volumetric yield and it can reduce the number of rejected lumber by visual grading. However, it could not identify better logs to produce higher-grade products. To find an appropriate log-sorting-method for structural products, log diameter and ultrasonic time of flight (TOF) for the log were considered as factors to affect mechanical performance of resulting products. However, it was found that influence of log diameter on mechanical performance of resulting products was very small. The TOF showed a possibility to sort logs by mechanical performance of resulting products even though a coefficient of correlation was not strong (R = 0.6). In a case study, the log selection based on the ultrasonic TOF of the log increased the yield of the outermost tension lamination (E8 or better grade, KS F 3021) from 2.6% to 12.5% and reduced LTE5 (lower than E5 grade) lamination from 43.6% to 10.3%, compared with the existing KFRI log grading rule.

• Proceeding of KASS Symposium
• /
• 2008.05a
• /
• pp.49-52
• /
• 2008

Structural Wood is developed by purpose to make efficient use of wood resources. The biggest advantage of structural wood is stable as strength is high than wood product that is used by structure in existing. Order manufacture according to design details is available. It Is used to main structure elements to large spatial structure. Structure wood kind utilizes Glulam, prefabricated wood I-joists and laminated veneer lumber(LVL) and so on. Structural Design and construction of Open-air Stage Roof Structure is described in the presented paper. Architectural roof materials is used to PVF/PFLT membrane. Column and diagonal members is used to steel members(SS400), and Cantilever beam is used to Glulam assembled with different Grade laminations(10S-28B).

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.521-530
• /
• 2011

Nowadays, market demand of structural Glulam is growing and diversifying. The durability of Glulam should be significantly considered when they are intended to apply for out-door use such as timber bridge and pergola. This study was aimed to develop the manufacturing process of preservative treated structural Glulam using domestic softwood species. 10 m long structural Glulam were manufactured from domestic pitch pine logs with CuAz-3 preservative treatment. At each manufacturing process, the production yield was evaluated. Finally, bending tests were performed to verify the structural performance of manufactured Glulam. From the results, it was shown that the preservative treatment process hardly influenced on the production yield. But domestic pitch pine was proved to not be suitable for making the preservative treated Glulam due to the large difference of preservative permeability between sapwood and heartwood.

• Journal of the Korea Furniture Society
• /
• v.21 no.3
• /
• pp.216-228
• /
• 2010

Recently, there is a new issue, among the contemporary people, for new life style, such as green design and well being. This trend brought up the necessity that there should be alternatives for interior spatial design. In order to catch up with these new issues, the new convenient and environment friendly methods are in need. Space composition using setting-up is skill that can express both the structural aspect and esthetic because it represents traditional beauty into the contemporary age through the structural rigidity and formal beauty. Also the lumber, as main materials for setting up, is in line with well being life style and environment friendliness. The construction of structure by setting-up has advantages in terms of the reuse and the convenience in that the construction of structure is adjustable according to environment. And setting-up has enough plasticity not only because of its own role as linking the objects but also because of being framed by itself. Therefore setting-up will be a design element, if it is expressed outward. Thus, this study aims to give a guide line about how to apply the result from the evaluating that "what is the most suitable setting-up" and "what is the most suitable detail setting-up", based on that structural rigidity, decorativeness and the ease of works. As a result of evaluation, the most excellent types of setting-up in terms of structural rigidity are "Jangbu" and "Panjae" and "Yeongui". The most excellent types of setting-up in terms of decorativeness are "Panjae" and "Yeongui", and the most excellent type of the ease of work is "Mat". And also the most applicable detail setting-up for the utilization of spatial composition is proposed.

• Structural Engineering and Mechanics
• /
• v.73 no.3
• /
• pp.353-365
• /
• 2020

In the previous studies, the authors proposed the use of laminated veneer lumber - carbon fiber reinforced polymer (LVL-CFRP) composite beams for structural application. Bond strength of the LVL-to-CFRP interface and flexural strengthening schemes to increase the bending capacity subjected to positive and negative moment were discussed in the previous works. In this article, theoretical models are proposed to predict the moment capacity when the LVL-CFRP beams are subjected to negative moment. Two common failure modes - CFRP fracture and debonding of CFRP are considered. The non-linear model proposed for positive moment is modified for negative moment to determine the section moment capacity. For the debonding based failure, previously developed bond strength model for CFRP-to-LVL interface is implemented. The theoretical models are validated against the experimental results and then use to determine the moment-rotation behaviour and rotational rigidity to compare the efficacy of various strengthening techniques. It is found that combined use of bi- and uni-directional CFRP U-wrap at the joint performs well in terms of both moment capacity and rotational rigidity.