• Nuclear Engineering and Technology
• /
• 제52권8호
• /
• pp.1862-1870
• /
• 2020

The purpose of this study is to investigate the effect of welding residual stress on operating stress in designing a nuclear turbine welded rotor. A two-dimensional axisymmetric finite element model is employed to calculate the residual stress before and after post weld heat treatment (PWHT), and then the superposition of residual stress after PWHT and operating stress at normal speed and overspeed were discussed. The investigated results show that operating stress can be affected significantly by welding residual stress, and the distribution trend of superposition stress at the weld area is mainly determined by welding residual stress. The superposition of residual stress and operating stress is linear superposition, and the hoop stress distribution of superposition stress is similar with the distribution of residual stress. With the increasing overspeed, the distribution pattern of the hoop superimposed stress remains almost unchanged, while the stress level increases.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.172-181
• /
• 2003

In this study, the stress intensity factor of center crack tip is calculated by the superposition method when it is surrounded by symmetrically distributed small cracks. The values of stress intensity factors of center crack tips are compared with those of the center crack tips calculated by the superposition method. These compared errors are influenced by the locations of distributed small cracks. These errors are inspected. When small cracks overlap and approach near the center crack tip, the effect of interaction caused by these cracks becomes noticeable and these errors become larger. In case of multiple distributed small cracks except this case, the stress intensity factor of the center crack tip is easily calculated by the superposition method.

• 한국정밀공학회지
• /
• 제11권4호
• /
• pp.47-57
• /
• 1994

This study investigates the crack propagation behavior to examine the effect of welding residual stress by the superposition method. Especially, as the crack propagation behavior is affected by the applied stress and the stress ratio in compressive residual stress filed, it is studied for three cases as follows; (1) $K_{min}$is smaller than l $K_{r}$l, (2) $K_{min}$ is smaller than l $K_{r}$l in the later stage, (3) $K_{min}$is lager than l $K_{r}$l. The resuslts show that the superposition method is very useful in all the three cases of compressive residual stress field, but is inappropriate in predicting the crack propagation behavior in tensile residual stress field.field.field.

• Journal of Welding and Joining
• /
• 제7권1호
• /
• pp.28-35
• /
• 1989

The fatigue crack growth behavior in GTA butt welded joints of Al-Alloy 5052-H38 was examined using Single Edge Notched(SEN) specimens. It is well known that welding residual stress has marked influence on fatigue crack growth rate in welded structure. In the general area of fatigue crack growth in the presence of residual stress, it is noted that the correction of stress intensity factor (K) to account for residual stress is important for the determination of both stress intensity factor range(.DELTA.K) and stress ratio(R) during a loading cycle. The crack growth rate(da/dN) in welded joints were correlated with the effective stress intensity factor range(.DELTA.Keff) which was estimated by superposition of the respective stress intensity factors for the residual stress field and for the applied stress. However, redistribution of residual stress occurs during crack growth and its effect is not negligible. In this study, fatigue crack growth characteristics of the welded joints were examined by using superposition of redistributed residual stress and discussed in comparison with the results of the initial welding residual stress superposition.

• 한국정밀공학회지
• /
• 제15권11호
• /
• pp.244-250
• /
• 1998

In this study, the stress intensity factors of center crack are analyzed when it is surrounded by symmetrically distributed small cracks. The values of stress intensity factors of the center crack are greatly influenced by the locations of distributed small cracks. When small cracks overlap or approach near the tip of a center crack, the effect of interaction arisen by these cracks becomes noticeable. In case of multiple distributed small cracks, the stress intensity factor of a center crack is found to be efficiently determined by the superposition method.

• Advances in aircraft and spacecraft science
• /
• 제5권2호
• /
• pp.259-275
• /
• 2018

In mechanical analysis of spacecraft structures situations appear where static and dynamic loads must be considered simultaneously. This could be necessary either by load definition or preloaded structures. The superposition of these environments has an impact on the load and stress distribution of the analysed structures. However, this superposition cannot be done by adding both load contributions directly. As an example, to compute equivalent Von Mises stresses, the phase information must be taken into account in the stress tensor superposition. Finite Element based frequency response solvers do not allow the calculation of superposed static and dynamic responses. A manual combination of loads in a post-processing task is required. In this paper, procedures for static and harmonic loads superposition are presented and supported by analytical and finite element-based examples. The aim of the paper is to provide evidence of the risks of using different superposition techniques. Real application examples such as preloaded mechanism structures and propulsion system tubing assemblies are provided. This study has been performed by the Structural Engineering department of Airbus Defence and Space GmbH Friedrichshafen.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.943-944
• /
• 2010

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.92-96
• /
• 2008

An investigation was performed to predict residual stress redistribution for the crack propagation initially through tensile residual stress field. The analytical method, which is based on Dugdale model by finite element analysis using elastic analysis method considering the superposition principle, was proposed to estimate the redistribution of residual stress caused by crack propagation. The various aspect of distribution of residual stress caused by crack propagation was examined based on the configuration change of specimen. The analysis results show that the aspect of redistribution of residual stress caused by crack propagation depends on the width of the specimen provided that the initial distribution of residual stress is identical.

• 한국방재학회 논문집
• /
• 제1권2호
• /
• pp.103-114
• /
• 2001

PSC box girder의 정착부 설계방법들을 비교해본 결과, 기존 시방서에 따른 설계방법에서는 다수의 정착구에 긴장력이 작용할 때 긴장력의 작용순서와 그 크기에 따른 응력의 중첩효과를 고려할 수 없는 단점을 가지고 있었고, 3차원 유한요소해석을 이용한 설계에서는 응력집중부와 응력흐름을 정확히 파악할 수는 있지만 부재의 단면력을 산정하기가 매우 번거롭고 까다롭다는 단점을 가진다. 그러나 strut-tie 모델을 이용한 설계법에서는 긴장력의 긴장순서에 따른 응력중첩효과를 고려할 수 있고 부재의 단면력의 산정 또한 매우 간편하여 긴장력의 도입순서에 의해 변화하는 응력의 흐름을 잘 파악하여 strut-tie로 구성된 트러스 부재들의 기하학적 조건을 만족하도록 유의한다면 정착부의 설계에 가장 적합한 설계방법이라 할 수 있다.

• Journal of Welding and Joining
• /
• 제21권6호
• /
• pp.77-83
• /
• 2003

The finite element analysis was performed for the cracks existing in residual stress fields in order to investigate the effects of configuration of residual stress distribution to the fatigue crack opening behaviour. And the variation of stress distributions adjacent to the crack caused by uploading was examined. The finite element model with contact elements for the crack plane and plane stress elements for the base material and the analytical method based on the superposition principle to estimate crack opening behaviour and the stress distribution adjacent to the crack subjected to uploading were used. The results of the analysis showed that crack opening behaviors and variations of stress distribution caused by uploading were changed depending on the configuration of residual stress distribution. When the crack existed in the region of compressive residual stress and the configuration of compressive residual stress distribution were inclined, a partial crack opening just behind of a crack tip occurred during uploading. Based on the above results, it was clarified that the crack opening behaviour in the residual stress field could be predicted accurately by the finite element analysis using these analytical method and model.