• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.101-112
• /
• 1994

The measurement of residual stress distribution of $Si_3N_4/SUS304$ joint was performed on 23 specimens with the same joint condition using PSPC type X-ray stress measurement system and the two-dimensional elastoplastic analysis using finite element method was also attempted. As results, residual stress distribution near the interface on the ceramic side of the joint was revealed quantitatively. Residual stress on the ceramic side of the joint was turned out to be tensional near the interface, maximum along the edge, varying in accordance with the condition of the joint and variance to be most conspicuous for the residual stress normal to the interface characterized by the stress singularities. In the vicinity of the interface, the high stress concentration occurs and residual stress distributes three-dimensionally. Therefore, the measured stress distribution differed remarkably from the result of the two-dimensional finite-element analysis. Especially at the center of the specimen near the interface, the residual stress, $\sigma_{x}$ obtained from the finite element analysis was compressive, whereas measurement using X-ray yielded tensile $\sigma_{x}$. Here we discuss two dimensional superposition model the discrepancy between the results from the two dimensional finite element analysis and X-ray measurement.

• 한국정보통신학회논문지
• /
• 제12권10호
• /
• pp.1717-1722
• /
• 2008

스트레스 정도를 측정하기 위한 다양한 도구들이 많이 사용되고 있다. 스트레스 측정에는 심리측정과 생체측정이 있다. 어느 한쪽만을 고려하였을 경우 주관적이거나 객관적 결여가 발생한다. 그 문제점을 보완하기 위해 두 측정을 혼합한 새로운 스트레스 지수가 필요하다. 개인적 특성에 따라 측정 결과도 다양하게 나타나지만, 현재 사용되고 있는 측정도구를 바탕으로 한 일반적인 경우를 고려하여 연구하였다. 심리와 생체 측정 도구를 통해서 얻어지는 지수를 이용하여 통합적인 스트레스 지수를 얻는다. 그래서 임의로 4가지의 스트레스 측정도구를 사용한다. 각 측정도구에서 나온 결과에 대한 멀티지수가 나타나는데, 그 지수들을 각각 좌표평면에 나타내어 스트레스에 대한 균형성과 편향성을 분석하고 진단한다.

• 한국컴퓨터정보학회논문지
• /
• 제22권6호
• /
• pp.87-93
• /
• 2017

In this paper, we design a small low power single channel ECG(Electrocardiogram) system of Chest Belt type with fiber-type electrodes to measure emotional state change of game addict. HRV(Heart Rate Variability) is analyzed through heart rate signal measurement and the psychological stress state is judged by using it. And it verifies its effectiveness through prototype. First, we design HR measurement module through low power MCU(Micro Controller Unit) and implement prototype level measurement system. The results showed that the difference between the addiction group and the general group was confirmed and that the system was effective. The result of this study can be used for health management such as reduction of stress of the user through music and breathing that lowers the stress by detecting the stress state of the general person or the chronic ill person.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.721-725
• /
• 1996

The microfabricated test structures were used in order to evaluate the stress characteristics in films. The test structures were fabricated using surface micromachining technique, including HF vapor phase etching as an effective release method. The fabricated structures were micro strain gauge, cantilever-type vernier gauge and bridge for stress measurement, and cantilever for stress gradient measurement. The strain was measures by observing the deformation of the structures occurred after release etching and the amount of deformation can be detected by micro vernier gauge, which has gauge resolution of 0.2${\mu}{\textrm}{m}$. The detection principles and the degree of precision for the measured strain were also discussed. The characteristics of residual stress in LPCVD polysilicon films were studied using these test structures. The stress gradient due to the stress variation through the film thickness was calculated by measuring the deflection at the cantilever free end.

• 한국압력기기공학회 논문집
• /
• 제7권1호
• /
• pp.9-16
• /
• 2011

Primary water stress corrosion cracking (PWSCC) has been found in the weld region of the nuclear power plant. Welding can produce tensile residual stress. Tensile residual stress contributes to the initiation and growth of PWSCC. It is important to estimate weld residual stress accurately to predict or prevent the initiation and growth of PWSCC. This paper shows the results of finite element analysis and measurement experiment for weld residual stress. For the study, four kinds of specimen were fabricated with the materials used in the nuclear power plant. Residual stresses were measured by four kinds of methods of hole drilling, x-ray diffraction, instrumented indentation and sectioning. Through the study, numerical analysis and measurement results were compared and the characteristics of each measurement technique were observed.

• Journal of Magnetics
• /
• 제22권2호
• /
• pp.281-285
• /
• 2017

To suppress the wall slip effect and improve the yield stress measurement precision of magnetorheological fluid, measurement disks with different grooves are first manufactured. Then, the influence of groove characteristics on the yield stress of magnetorheological fluid is investigated by the method of experiments. Finally, the optimization wall grooves of measurement disks are obtained, and the yield stress of a self-prepared magnetorheological fluid is measured. Results indicate that the groove type and groove width have a slight influence on the shear yield stress, whereas the measured yield stress increases with enhanced groove density, and the optimized groove depth is 0.3 mm. The measured shear yield stress of self-prepared MR fluid can be improved by 18 % according to the optimized grooved disks, and the maximum yield stress can reach up to 65 kPa as the magnetic flux density is 0.5 T.

• 스마트미디어저널
• /
• 제13권2호
• /
• pp.44-51
• /
• 2024

스트레스 측정용 데이터셋의 구축은 건강, 의료분야, 심리향동, 교육분야 등 현대의 다양한 응용 분야에서 핵심적인 역할을 수행하교 있다. 특히, 스트레스 측정용 인공지능 모델의 효율적인 훈련을 위해서는 다양한 편향성을 제거하고 품질 관리된 데이터셋을 구축하는 것이 중요하다. 본 논문에서는 다양한 편향성 제거를 통한 품질의 관리된 스트레스 측정용 데이터셋 구축에 관하여 제안하였다. 이를 위해 스트레스 정의 및 측정도구 소개, 스트레스 인공지능 데이터 셋 구축과정, 품질향상을 위한 편향성 극복 전략 그리고 스트레스 데이터 수집시 고려사항을 제시하였다. 특히, 데이터셋 품질을 관리하기 위해 데이터셋 구축시 고려사항과, 발생할 수 있는 선택편향, 측정편향, 인과관계편향, 확증편향, 인공지능편향과 같은 다양한 편향서에 대해 검토하였다. 본 논문을 통해 스트레스 데이터 수집시 고려사항과 스트레스 데이터셋의 구축에서 발생할 수 있는 다양한 편향성을 체계적으로 이해하고, 이를 극복하여 품질이 보장된 데이터셋을 구축하는데 기여할 것으로 기대된다.

• Korea-Australia Rheology Journal
• /
• 제14권1호
• /
• pp.17-23
• /
• 2002

A novel and simple method using a cylindrical penetrometer is being developed for the measurement of yield stress. The principle of this technique is based on the measurement of the static equilibrium of a falling penetrometer in a yield stress fluid. The yield stress is simply determined by a balance of forces acting on the penetrometer. The yield stress of Carbopol gels and $TiO_2$ suspensions has been measured using this method. The results are in reasonable agreement with the values from conventional methods. The effects of the dimensions and weight of the penetrometer have been examined. The long-term behaviour was also observed. No measurable creep was seen and equilibrium was found to be very quickly established. The cylindrical penetrometer technique promises to be a simple, quick and reliable static method for the measurement of yield stress.

• 대한인간공학회지
• /
• 제32권1호
• /
• pp.47-58
• /
• 2013

Objective: The aim of this study is to review the job stress measurement for applying in nuclear power plants(NPPs). Background: The standard and guideline to evaluate and manage the job stress is insufficient in NPPs. Although job stress might have a negative effect on task performance particularly it can be related with human error in NPPs. Method/Results: This paper considered the objective and subjective stress measurements. One of the questionnaire(Korean Occupational Stress Scale) and the experiment method was investigated to apply in NPPs. KOSS was analyzed about the inter item consistency and correlation with the workload, and relative importance. In the objective evaluation considered the experiment method for the physical and mental job stress and analyzed from the phased point of view. Conclusion/Application: The measurement and criteria to evaluate job stress for operators must be complemented on the job characters and environments in NPPs. This study may support to confirm and manage the job stress in NPPs. The study of more specific methodology on job stress in NPPs is required on the basis of this paper.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.431-438
• /
• 2005

In this paper, the characteristics of excessive horizontal stress components in Korea were studied using the in-situ hydraulic fracturing stress measurement data over five hundred in 110 individual test boreholes. Based on the in-situ testing data, the magnitude and orientation of the horizontal stress component and variation of stress ratio (K) with depth were investigated. And also horizontal stress magnitude versus depth relationships and distribution limits of stress ratio components were suggested. For the subsurface space above 310 m depth in the entire territory, the stress ratio has a tendency to diminish and be stabilized with depth, but for some areas, it was revealed that the excessive horizontal stress fields with stress ratio close to 3.0 below 200 m in depth have formed. The result of investigation for excessive horizontal stress regions indicates that there exist several regions above 300 m in depth where localized excessive horizontal stresses enough to induce potentially brittle failure around future openings have formed.