• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.3-9
• /
• 1984

This study was carried out to examine the practicality of DAP[$(NH_4)_2HPO_4$] as fire retardant for plywood by static bending test the redried plywoods which had been soaked in 20% $(NH_4)_2HPO_4$ solution. Being hot/cold soaked in the solution for 3/3, 6/3, 9/3 and 12/3 hours and redried by cyclic press-drying method at the platen temp. of 130, 145, 100 and $175^{\circ}C$, the treated plywoods were tested to offer the mechanical data, that is, $S_{pl}$(stress at proportional limit), MOE(modulus of elasticity), MOR(modulus of rupture) and $W_{pl}$(work per unit volume to proportional limit ) in flexure. The results obtained were summarized as follows. 1. $S_{pl}$ of fire retardant treated plywoods ("FRP" would be used hereinafter) decreased as the platen temperature increased, but it was superior to that of non-treated plywoods(Control) at $160^{\circ}C$ or higher. 2. MOE of FRP decreased roughly with the increase of temperature, hut this tendency was not constant. And the value of FRP was higher than that of Control even at $175^{\circ}C$. 3. MOR of FRP showed same temperature-dependent tendency as MOE, but it was influenced more sensitively at the higher temperature. 4. $W_{pl}$ of FRP also decreased gradually with the increase of platen temperature and the value in DAP 9/3 treatment was Jess than 70% of control plywoods. 5. In view of redrying time and mechanical properties, the most reasonable platen temperature for DAP treated FRP was $160^{\circ}C$ in this study.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.7-12
• /
• 2005

The objective of this study is to estimate the mechanical behavior in bending and the anatomical changes of wood under several deflection rates. Sample specimens of water-saturated Japanese cedar (Cryptomeria japonica) were stressed to rupture under several deflection rates. Mechanical properties of wood such as modulus of elasticity, modulus of rupture and stress at proportional limit, and anatomical changes affected by deflection rates were estimated. Microscopic observations on compression side of the test specimens when the specimen was loaded to rupture were carried out by the SEM (scanning electron microscopy). The results are summarized as follows: 1. The mechanical properties of wood were affected by variations of the deflection rates. The modulus of elasticity (MOE), modulus of rupture (MOR) and stress at proportional limit were in proportion to the logarithm of deflection rates. 2. The deflection of wood at rupture in bending increased as deflection rates decreased. 3. The variations of the microscopic deformations of sample specimens were closely related to the deflection of wood at rupture. In case of largely deflected wood by maximum bending load, severe and abundant microscopic deformations were observed.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.59-66
• /
• 2001

Fatigue strength of the welding structure is governed by the residual stress at the weldment toe and static tensile overloads were known as relieving the residual stresses. In this study, static tensile overloads were applied to the welding structures which caused the relief of residual stresses. The amount of residual stress relief was found as proportional to the change of fatigue limit at the given conditions. Based on the fact of the proportionality between the change of fatigue limit and that of residual stress, simple measurement technique is proposed. Modified stress-life curves base on proposed technique gave good agreement with test results.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.57-62
• /
• 2008

The aim of this investigation was to extract the fatigue properties at the designated fatigue life of copper foil and observe the mean stress and stress amplitude effects on both the fatigue life and the corresponding surface morphology. Tensile tests were performed to determine the baseline monotonic material properties of the proportional limit and ultimate tensile strength. Constant amplitude fatigue tests were carried out using a feedback-controlled fatigue testing machine. The mean stress and the stress amplitude were changed to obtain the complete nominal stress-life curves. An atomic force microscope was utilized to observe the relationship between the fatigue damage and the corresponding changes in surface morphology. A Basquin's exponent of-0.071 was obtained through the fatigue tests. An endurance limit of 122 MPa was inferred from a Haigh diagram. The specimen surface became rougher as the number of fatigue cycles increased, and there was a close relationship between the fatigue damage and the surface roughness evolution.

• Journal of the Korean Wood Science and Technology
• /
• 제12권4호
• /
• pp.12-18
• /
• 1984

열판온도(熱板溫度)가 내화약제(耐火藥劑)로 처리(處理)된 합판(處理)의 재건조(再乾燥) 후(後) 곡강도(曲强度)에 미티는 영향(影響)을 조사(調査)하기 위해 두께 3.5mm 메란티합판(合板)을 황산(黃酸)암모늄, 제1(第一)인산암모늄, 제2인산(第二燐酸)암모늄 그리고 혼합약제(混合藥劑)인 붕사(硼砂) 붕산(硼酸) 및 미나리스 등(等) 5종(種)의 내화제(耐火劑)의 20% 수용액(水溶液)에 9시간(時間)동안 침지처리(浸漬處理)한 다음, 각각(各各) 열판온도(熱板溫度) $90^{\circ}C$, $120^{\circ}C$ 및 $150^{\circ}C$를 적용(適用)한 단계별(段階別) 건조방식(乾燥方式)으로 건조(乾燥)하여 곡강도시험(曲强度試驗)을 행(行)하였다. 비례한계(比例限界)에서의 응력(應力), 탄성계수(彈性係數), 파괴계수(破壞係數) 및 비례한계(比例限界)까지의 단위체적당(單位體積當) 일 등(等)을 조사(調査)한 바, 수분처리대조구(水分處理對照區)의 경우, 열판온도(熱板溫度) $120^{\circ}C$까지 유지(維持)되던 강도(强度)가 $150^{\circ}C$에 이르러서는 현저한 감소경향(減少傾向)을 나타내었으나, 내화약제처리합판(耐火藥劑處理合板)은 $150^{\circ}C$까지 열판온도(熱板溫度)가 상승(上昇)함에도 불구(不拘), 강도(强度)가 유지(維持)되었으며 일부 약제처리(藥劑處理)의 경우엔 오히려 증가(增加)하는 양상(樣相)도 보여주었다. 건조속도(乾燥速度)와 강도유지(强度維持)의 측면(側面)을 고려할 때, 바람직한 열판건조온도(熱板乾燥溫度)는 $150^{\circ}C$ 였으며 내화약제중(耐火藥劑中) 보강효과(補强效果)가 가장 좋은 약제(藥劑)는 붕사(硼砂) 붕산(硼酸)이었다.

• Journal of the Korean Wood Science and Technology
• /
• 제18권4호
• /
• pp.86-101
• /
• 1990

The primary objective of this research was to investigate the strength properties of Comply, a composite panel. fabricated with particle board as core material and veneer or plywood as face and back. 20types of comply composites were manufactured according to the four specific gravity levels(0.5, 0.6, 0.7 or 0.8) of particleboard core and three veneer or two plywood thicknesses for face and back. They were tested and compared with matching particleboard (control) on moisture content. specific gravity, bending properties(MOE, MOR SPL). nail resistance and internal bond strength. The obtained results were summarized as follows: The increasing effect of modulus of elasticity was shown by the increase of face and back veneer or plywood thickness. The modulus of rupture and stress at proportional limit of the comply composites bonded with 3mm thick veneers or 3mm thick plywood face and back were higher than 2mm thick veneer or 2mm thick plywood as face and back. Both of modulus of rupture and stress at proportional limit on bending of Comply were higher than those of control board. Also the modulus of elasticity of Comply showed much higher than that of control board. The nail resistance of Comply, composed of plywood as face and back was higher than that of veneer. The nail resistance of control board was higher than that of Comply at Sp.Gr 0.7 and 0.8 core boards. Internal bond of Comply, composed of 1mm and 2mm thick veneer as face and back was higher than that of 3mm thick veneer. The increasing effect of modulus of elasticity was shown by the increase of shelling ratio in Comply composed of veneer and plywood as face and back. The modulus of rupture was increased by the increment of shellmg ratio in Compiy, composed of plywood as face and back. The modulus of elasticity and modulus of. rupture of comply were higher than those of particleboard(control) in effect of shelling ratio. Therefore it was concluded that the mechanical property values of Comply were clearly greater than those of particleboard(control).

• Journal of the Korean Wood Science and Technology
• /
• 제13권4호
• /
• pp.67-72
• /
• 1985

To improve the bending strength of sawdustboard, verious resin contents of 10, 13, 16, and 19% were applied to the thin shell (face layer) composed with wire net or not. The shell effect of sawdust and wire net composition formed with core sawdustboard were evaluated. Forcusing on the effects of wire net composition and noncomposition including a comparison with chipboard and veneer complyboard, bending properties (Modulus of rupture (MOR), Modulus of elasticity (MOE), Stress at proportional limit ($S_{pl}$). Work to maximum load ($W_{ml}$))were analyzed and discussed. 1. In modulus of rutpute, veneer comply was the highest (621.5 kg/$cm^2$), and next decreasing order was wire net composition (159.1 kg/$cm^2$), chipboard (81.75 kg/$cm^2$), and wire net noncomposition (76.21 kg/$cm^2$) as in modulus of elasticity, work to maximum load, except for stress at proportional limit. 2. The highly significant effects were shown in both wire net composition and noncomposition, at the same time wire net composition exceeded two times of noncomposition throughout resin contents in bending properties. Chipboard was similar to the mean or 16% resin content in noncomposirion. 3. Every board in wire net composition above 10% resin content was beyond 100 kg/$cm^2$ in MOR, minimum allowable strength for structural use according to KS F 3104. In conclusion, the feasibility for improving the bending strength of weak sawdustboard by wire net composed shell was offered.

• Journal of the Korean Wood Science and Technology
• /
• 제18권2호
• /
• pp.67-78
• /
• 1990

This study was performed to determine the characteristics of physical and mechanical properties of domestic wood based materials; plywood, particleboard, medium density fiberboard. Main items of tested properties were panel size, moisture content, water absorption, linear expansion and thickness swelling, glue bond shear strength, bending properties(stress at proportional limit, modulus of rupture. modulus of elasticity), tensile strength, screw holding strength, and internal bond as neccessary. the results were discussed mainly with Korean Standards. The obtained conclusions are as follows; 1. Length and width of 3mm thin plywood(3-ply) and 12mm thick plywood(7-ply) were satished with KS-standard, but thicknesses of these panels were not- passed tolerance limit except one of eight makers. 2. Length and width of particleboard and medium density fiberboard were greater than the tolerance limit value of KS standard, but the thicknesses of these panels were passed this value. 3. Moisture contents of 12mm thick and 3mm thin plywood were satisfied with KS-standard except one mill made 3mm thin plywood. 4. Moisture absortion of plywood was not passed tolerance limit of KS-standard but particleboard was satisfied with this standard value. 5. Dry and wet shear strengths in glue bond of 3mm thin plywood were not reached to KS-standard, but those of 12mm thick plywood were sufficiently satisfied with KS standrad. 6. Modulus of ruptures, parallel to grain and perpendicular to grain of plywood, and particleboard and medium density fiberboard were satisfied with KS-standard. 7. Tensile strengths, parallel to grain and perpendicular to grain of plywood were satisfied with allowance stress of US product standard PS 1-74. 8. Screw holding strength of particleboard was not reached to KS standard, but internal bond was satisfied with KS standard.

• 한국공간구조학회논문집
• /
• 제19권2호
• /
• pp.73-81
• /
• 2019

The high-temperature properties of mild steels were studied by comparing the test results of Kwon and the yield strength, tangent modulus predicted by the design provisions of ASCE and Eurocode(EC3). The column strengths for steel members at high temperatures were determined by the elastic and inelastic buckling strengths according to elevated temperatures. The material properties at high temperatures should be used in the strength evaluations of high temperature members. The buckling strengths obtained from the AISC, EC3 and approximate formula proposed by Takagi et al. were compared with ones calculated by the material nonlinear analysis using the EC3 material model. The newly simplified formulas for yield stress, tangent modulus, proportional limit and buckling strength which were proposed through a comparative study of the material properties and buckling strengths. The buckling strengths of proposed formulas were approximately equivalent to ones obtained from the formulas of Takagi et al. within 4%. They were corresponded to the lower bound values among the buckling strengths calculated by the design formulas and inelastic buckling analysis.

• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.20-26
• /
• 1984

내화처리(耐火處理)된 합판(合板)의 내부(內部)에 잔존(殘存)하고 있는 내화약제(耐火藥劑)의 종류(種類) 및 그 양(量)이 합판(合板) 특유(特有)의 장점(長點)인 휨 강도(强度)에 어떠한 영향(影響)을 미치는 가를 조사(調査)하기 위(爲)해 황산(黃酸) 암모늄(Ammonium sulfate), 제1인산(第一燐酸) 암모늄(Ammonium phosphate, mono basic), 제2인산(第二燐酸) 암모늄(Ammonium phosphate, di basic), 그리고 복합약제(複合藥劑)인 붕사(硼砂) 붕산(硼酸)(Borax-Boric acid) 및 미나리스(Minalith) 등(等) 5종(種)의 내화제(耐火劑)를 20% 수용액(水溶液)으로 조제(調劑)한 다음 3.5mm 메란티 합판(合板)을 3시간(時間)부터 12시간(時間) 동안 3시간(時間) 간격(間隔)으로 침지처리(浸漬處理)를 한 후(後) $120^{\circ}C$의 열판(熱板)으로 재건조(再乾燥)하여 휨 강도시험(强度試驗)을 행(行)하였다. 비례한계(比例限界)에서의 응력(應力), 탄성계수(彈性係數), 파괴계수(破壞係數) 및 비례한계(比例限界)까지의 단위체적(單位體積) 당(當) 일등(等)을 조사(調査)한 바, 약제처리(藥劑處理)한 합판(合板)의 경우가 수분처리합판(水分處理合板)(대희구(對熙區))에 비(比)해 대부분(大部分) 높게 나타났으며 붕사(硼砂) 붕산(硼酸) 처리합판(處理合板)의 경우가 4부간(部間)에서 공(共)히 가장 높은 치(値)를 보여주었다. 그리고 처리시간(處理時間)이 연장(延長)됨에 따라, 즉 약액(藥液)의 흡수량(吸收量)(약제(藥劑) 잔존량(殘存量))이 증가(增加)함에 따라 휨 강도(强度)는 대체적(大體的)으로 향상(向上)하는 것으로 나타났다. 강도적(强度的) 측면(側面)이나 침지처리시(浸漬處理時) 발생(發生)하는 결함(缺陷) 등을 고려(考慮)할 때 복합약제(複合藥劑)인 붕사(硼砂) 붕산(硼酸)이 가장 바람직한 합판용(合板用) 내화처리약제(耐火處理藥劑)로 사료되는 바이다.