• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1343-1350
• /
• 2000

The evolutionary structure of tip vortices has been investigated with a two-dimensional LDV system for a plain and a slotted blade, respectively. To analyze the effect of slots which bypasses a part of main stream into the tip face, velocity profiles, vortex sizes, their displacements and turbulence intensities during one revolution of the rotor were measured by the phase averaging process. For the comparison of circumferential velocity components of the plain blade and the slotted blade, the peak values of the slotted blade were lower than those of the plain blade, and axial velocity components of the slotted blade were considerably larger than those of the plain blade. The slotted rotor blade enlarged the core size and made the vortex delayed compared with those of the plain blade at the same wake ages. Turbulence profiles had peaks inside the core radii and decayed gradually in the radial direction of vortex coordinate. Also, using a quasi 3-D LDV measurement technique the budget of turbulence kinetic energy was analyzed in radial direction of the vortex core.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1613-1623
• /
• 1996

In this paper, two discretization methods, hybrid and QUICK, are tested for the Navier-Stokes equations written in general nonorthogonal body fitted coordinates. Comparison is made by calculating two laminar flows at low Reynolds numbers of 10 - 100. One is a two-dimensional channel of gradually expanding cross section and the other is an axisymmetric flow through a circular tube having a circular constriction. Results show that the QUICK scheme results in a numerical solution more accurate than that of hybrid. The QUICK scheme also shows faster convergence for both test cases. As the number of grid points increases, all numerical solutions converge with more oscillation. The number of grid points in the y-direction(cross stream direction) is also shown to play a significant role in the approximation of convection term within separated flow zone.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.621-626
• /
• 2006

Regenerative evaporative cooling is known as an environment-friendly and energy efficient cooling method. A regenerative evaporative cooler (REC) consisting of dry and wet channels is able to cool down the air stream below the inlet wet-bulb temperature. In the regenerative evaporative cooler, the cooling effect is achieved by redirecting a portion of the air flown out of the dry channel into the wet channel and spraying water onto the redirected air. In this study, a horizontal regenerative cooler is considered. In the horizontal regenerative cooler, the flow direction of evaporating water has a right angle to the flow direction of supply air. This difference was investigated with visualization technique and simplified 2-module performance test was done in a thermo-environment chamber. Optimum design configuration is changed due to the wet channel which are easily fully covered with evaporating water and block the air flow inside the channel. Applying the optimized fin configuration design with the highly wetting surface treatment, a regenerative evaporative cooler was fabricated and tested to Identify the cooling performance improvement and operation characteristics. From the experimental results at the intake condition of $32^{\circ}C$ and 50% RH, the supply temperature was measured to be around $23.4^{\circ}C$. The cooling effectiveness based on the inlet dewpoint temperature was evaluated 73% which is almost close to the design expectation.

• 한국지형학회지
• /
• 제25권2호
• /
• pp.31-42
• /
• 2018

This study analyzes the spatial distribution of the highest level terrace which can be regarded as an initial land surface before the uplift of the Taebaek Mountains and estimates spatial characteristics of the incision and uplift rates around the Mountains. The altitude above the riverbed of the 54 highest level terraces seems to be greatly influenced by the incision of large stream and their elevation shows a high correlation with the uplift of the Mountains. The elevation of the terraces in the north and middle parts decreases westward with a rate of 5~6 m/km and meets with the sea level at area 100~120 km apart from the Mountains. Therefore, it can be suggested that the west coast of Korea might have generally experienced subsidence during the Quaternary. The elevation of the terraces suggests that area with a direction of N-S or NNW-SSE from Yeoryang-myeon, Jeongseon-gun to Taebaek-si shows the highest uplift rate around the Mountains and area with a direction of N-S connecting Girin-myeon, Inje-gun and Pyeongchang-eup, Pyeongchang-gun also indicates a high uplift rate.

• 한국안전학회지
• /
• 제27권1호
• /
• pp.20-25
• /
• 2012

The purpose of the study is to assess the extinguishing concentration of inert gases in engine nacelle fire. The experiment was performed with a two dimensional rectangular bluff body stabilized flames, where the fuel was ejected to counter flow and co-flow against an oxidizer stream. Two inert gases, $CO_2$ and $N_2$, were used for extinguishing agent in the oxidizer and methane was used for fuel. The main experimental parameters were the direction of injecting fuel, the kinds of agent and the velocity ratio between air and fuel streams, which controlled the mixing characteristic near bluff body and the strength of recirculation zone in the downstream. The result shows the flame structure and the mode were strongly dependent with fuel/air ratio and the fuel jet direction. For both flow configurations, the extinguishing concentration of $CO_2$ was smaller than the $N_2$ because of the large heat capacity of $CO_2$. However, the concentration of inert gasesat blowout was much smaller than those in the cup burner and coflow jet diffusion flames, which implies that the extinction mechanism of bluff body stabilized flames was mainly due to the aerodynamic aspect. Compared to co-flow fuel injection, the extinguishing concentration of inert gases under counter flow configuration was lower. The effect of direction might result from the mixing characteristic and strength of recirculation zonearound a bluff body. More details should be investigated for the characteristic of recirculation zone in the wake of bluff body using the LES(Large Eddy Simulation).

• 한국멀티미디어학회논문지
• /
• 제18권8호
• /
• pp.988-995
• /
• 2015

In 2013, Academy Award for Best Animated Short Film was granted to Walt Disney's short animation, (2012). With various aspects of its excellence, I focus on the very effective use of digital lightings and underscores for storytelling as its success factors. In this respect, this paper aims at analyzing the roles of the visual factors, especially tone, contrast, etc. created by lightings, and audio factors, especially underscores, in the film's story development. I find that can be characterized by the well-built story structure with distinct three acts. The main stream of the story is expressed with the overall mood that is created by the fine adjustments of brightness of the main light, and contrast. And the direction and the intensity of the lighting successfully describe the emotions of the characters in each scene. In addition, I find that properly chosen and positioned underscores make the development of the story more dynamic and more harmonized.

• Journal of electromagnetic engineering and science
• /
• 제10권3호
• /
• pp.138-145
• /
• 2010

In this paper, we report the test results of a small-scale prototype that implements an analogue-beam-formed phased antenna array in the E-band. A four-channel dual-conversion receive RF module for 71~76 GHz frequency band has been developed and integrated with a linear end-fire antenna array. Measured performance is very close to the simulated results. An ad-hoc wireless communication system has also been demonstrated. Low BER was measured for an 8PSK data stream at 1.5 Gbps with the receive array beam formed in the direction of arrival of the transmitted signal. To our knowledge this is the first steerable antenna array reported to date in the E-band.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.92-96
• /
• 2007

Microphone array beamforming method has been recognized as an important aeroacoustic research field and become a standard technique in localizing sound sources. This method also used in flight acoustic measurement, and especially, it is very useful when measure sounds inside the wind tunnel. In measuring sound which is inside the wind tunnel by traditional beamforming method, there are some errors caused by airstream. The speed and the propagation path of the sound changes as it travel through the airstream. This makes the error which the position of sound is changed a little bit to the down stream direction. In this paper, validation test has made about the correction equation for this wind effects of previous researches. And beamforming including shear layer correction was performed about a sound source in the anechoic open-jet windtunnel.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.104-107
• /
• 2002

Direct Metal Manufacturing (DMM) is a new additive process that aims to take die making and metalworking in an entirely new direction. It is the blending of five common technologies : lasers, computer-aided design (CAD), computer-aided manufacturing (CAM), sensors and powder metallurgy. The resulting process creates parts by focusing an industrial laser beam onto a tool-steel work piece or platform to create a molten pool of metal. A small stream of powdered tool-steel metal is then injected into the melt pool to increase the size of the molten pool. By moving the laser beam back and forth, under CNC control, and tracing out a pattern determined by a computerized CAD design, the solid metal part is built line-by-line, one layer at a time. DMM produces improved material properties in less time and at a lower cast than is possible with traditional fabrication.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.46-55
• /
• 1996

As industrial standard data, the STL format which approximates three dimensional CAD model to triangular facets, is used for RP(Rapid Prototyping) system in recent days. Because most RP system take the only form of two dimensional line segments as an input stream inspite of its imperfectness while converting into STL format, a CAD model is converted into a standard industrial format which is composed of many triangular facets. The error verifying process is composed of four main steps, and these are 1) Remove facets with two or more vertices equal to each other. 2) Fix overlapping error such as more than three facets adjacent to anedge. 3) Fill holes in the mesh by using Delaunay triangulation method. 4) Correct the wrong direction and normal vectors. This paper is concerned with serching the mentioned errors in advance and modifying them.