• Wind and Structures
• /
• v.25 no.5
• /
• pp.433-457
• /
• 2017

As a novel typical wind-sensitive structure, the wind load and wind-induced structural behaviors of super-large straight-cone cooling towers are in an urgent need to be addressed and studied. A super large straight-cone steel cooling tower (189 m high, the highest in Asia) that is under construction in Shanxi Power Plant in China was taken as an example, for which four finite element models corresponding to four structural types: the main drum; main drum + stiffening rings; main drum + stiffening rings + auxiliary rings (auxiliary rings are hinged with the main drum and the ground respectively); and main drum + stiffening rings + auxiliary rings (auxiliary rings are fixed onto the main drum and the ground respectively), were established to compare and analyze the dynamic properties and force transferring paths of different models. After that, CFD method was used to conduct numerical simulation of flow field and mean wind load around the cooling tower. Through field measurements and wind tunnel tests at home and abroad, the reliability of using CFD method for numerical simulation was confirmed. On the basis of this, the surface flow and trail characteristics of the tower at different heights were derived and the wind pressure distribution curves for the internal and external surfaces at different heights of the tower were studied. Finally, based on the calculation results of wind-induced responses of the four models, the effects of stiffening rings, auxiliary rings, and different connecting modes on the dynamic properties and wind-induced responses of the tower structure were derived and analyzed; meanwhile, the effect mechanism of internal suction on such kind of cooling tower was discussed. The study results could provide references to the structure selection and wind resistance design of such type of steel cooling towers.

• The Journal of Korean Society for Radiation Therapy
• /
• v.14 no.1
• /
• pp.175-186
• /
• 2002

The purpose of this study is directly measure and evaluate about absorbed dose change according to nominal energy and electron cone or medical accelerator on isodose curve, percentage depth dose, contaminated X-ray, inhomogeneous tissue, oblique surface and irradiation on intracavitary that electron beam with high energy distributed in tissue, and it settled standard data of hish energy electron beam treatment, and offer to exactly data for new dote distribution modeling study based on experimental resuls and theory. Electron beam with hish energy of $6{\sim}20$ MeV is used that generated from medical linear accelerator (Clinac 2100C/D, Varian) for the experiment, andwater phantom and Farmer chamber md Markus chamber und for absorbe d dose measurement of electron beam, and standard absorbed dose is calculated by standard measurements of International Atomic Energy Agency(IAEA) TRS 277. Dose analyzer (700i dose distribution analyzer, Wellhofer), film (X-OmatV, Kodak), external cone, intracavitary cone, cork, animal compact bone and air were used for don distribution measurement. As the results of absorbed dose ratio increased while irradiation field was increased, it appeared maximum at some irradiation field size and decreased though irradiation field size was more increased, and it decreased greatly while energy of electron beam was increased, and scattered dose on wall of electron cone was the cause. In percentage depth dose curve of electron beam, Effective depth dose(R80) for nominal energy of 6, 9, 12, 16 and 20 MeV are 1.85, 2.93, 4.07, 5.37 and 6.53 cm respectively, which seems to be one third of electron beam energy (MeV). Contaminated X-ray was generated from interaction between electron beam with high energy and material, and it was about $0.3{\sim}2.3\%$ of maximum dose and increased with increasing energy. Change of depth dose ratio of electron beam was compared with theory by Monte Carlo simulation, and calculation and measured value by Pencil beam model reciprocally, and percentage depth dose and measured value by Pencil beam were agreed almost, however, there were a little lack on build up area and error increased in pendulum and multi treatment since there was no contaminated X-ray part. Percentage depth dose calculated by Monte Carlo simulation appeared to be less from all part except maximum dose area from the curve. The change of percentage depth dose by inhomogeneous tissue, maximum range after penetration the 1 cm bone was moved 1 cm toward to surface then polystyrene phantom. In case of 1 cm and 2 cm cork, it was moved 0.5 cm and 1 cm toward to depth, respectively. In case of air, practical range was extended toward depth without energy loss. Irradiation on intracavitary is using straight and beveled type cones of 2.5, 3.0, 3.5 $cm{\phi}$, and maximum and effective $80\%$ dose depth increases while electron beam energy and size of electron cone increase. In case of contaminated X-ray, as the energy increase, straight type cones were more highly appeared then beveled type. The output factor of intracavitary small field electron cone was $15{\sim}86\%$ of standard external electron cone($15{\times}15cm^2$) and straight type was slightly higher then beveled type.

• Wind and Structures
• /
• v.27 no.1
• /
• pp.11-27
• /
• 2018

The straight-cone steel cooling tower is a novel type of structure, which has a distinct aerodynamic distribution on the internal surface of the tower cylinder compared with conventional hyperbolic concrete cooling towers. Especially in the extreme weather conditions of strong wind and heavy rain, heavy rain also has a direct impact on aerodynamic force on the internal surface and changes the turbulence effect of pulsating wind, but existing studies mainly focus on the impact effect brought by wind-driven rain to structure surface. In addition, for the indirect air cooled cooling tower, different additional ventilation rate of shutters produces a considerable interference to air movement inside the tower and also to the action mechanism of loads. To solve the problem, a straight-cone steel cooling towerstanding 189 m high and currently being constructed is taken as the research object in this study. The algorithm for two-way coupling between wind and rain is adopted. Simulation of wind field and raindrops is performed with continuous phase and discrete phase models, respectively, under the general principles of computational fluid dynamics (CFD). Firstly, the rule of influence of 9 combinations of wind sped and rainfall intensity on flow field mechanism, the volume of wind-driven rain, additional action force of raindrops and equivalent internal pressure coefficient of the tower cylinder is analyzed. On this basis, the internal pressures of the cooling tower under the most unfavorable working condition are compared between four ventilation rates of shutters (0%, 15%, 30% and 100%). The results show that the 3D effect of equivalent internal pressure coefficient is the most significant when considering two-way coupling between wind and rain. Additional load imposed by raindrops on the internal surface of the tower accounts for an extremely small proportion of total wind load, the maximum being only 0.245%. This occurs under the combination of 20 m/s wind velocity and 200 mm/h rainfall intensity. Ventilation rate of shutters not only changes the air movement inside the tower, but also affects the accumulated amount and distribution of raindrops on the internal surface.

• Progress in Medical Physics
• /
• v.12 no.1
• /
• pp.95-102
• /
• 2001

The intracavitary cones were designed which were made of stainless steel and have scratched inside cone to be generated electron scatter and designed to be attached easily to the LINAC collimator and controlled cones length to be contacted smoothly between the patient and the cone tip. Two types of intracavitary cones were designed. One is the straight end cones with circular opening on the distal end and the other is 30 degree beveled end cones with elliptical opening on the distal end. Each type of intracavitary cone ranged in daimeter from 2.5 cm to 3.5 cm and required a separate set of lower trimmer annulias cone diameter. The film phantom was designed with an internal cassette that accurately aligned the film edge with the film phantom surface. Film optical density data were measured by photodensitometer(Wellhofer 700i) Dosimetry measurements were made to commission the LINAC for 6 - 20 MeV electron using the intracavitary cones. Isodose curves were measured for all energy and cones combinations. Output is defined as the maximum dose per MU along the clinical central axis in water at 113 cm SSD. Calibration output, defined to be the output for the 15cm$\times$15cm diameter straight cone, was adjusted to 1.00 cGy/MU at each energy according to the TG-21 protocol.

• Imaging Science in Dentistry
• /
• v.39 no.2
• /
• pp.81-87
• /
• 2009

Purpose: To evaluate the anteroposterior length and buccal angle of the anterior loop, and the size and location of the mental foramen using cone beam computed tomography (CBCT). Materials and Methods: 100 CBCT images from 87 adults (43 males and 44 females) ranging in age from 20 to 73 years (average 50 years) with edentulous ridge of the mandibular premolar region were obtained. Axial, sagittal, coronal images were reconstructed from Dental and Block Images of CBCT. The anteroposterior length, shape and buccal angle of the anterior loop, and the size and location of the mental foramen were calculated from reconstructed images of axial, sagittal and coronal CBCT. Results: The anteroposterior length and buccal angle of the mental canal was 4.0${\pm}$1.2mm, 37.8${\pm}$11.60$^{\circ}$respectively. The loop type with straight course was the most common shape of the mental canal. The location of the mental foramen below the apex of the lower second premolar (78%) was the most common. The maximum size of the mental foramen was 4.6${\pm}$1.0 mm in width and 3.0${\pm}$0.6 mm in height. The inner size of the mental canal was 2.6${\pm}$0.6 mm in width and 2.1 mm${\pm}$0.4 mm in height. Conclusion: CBCT is useful to evaluate the anterior loop and mental foramen of the mandibular canal. Safe guideline of 4 mm from the most anterior point of the mental foramen is recommended for implant and surgical treatment. (Korean J Oral Maxillofac Radiol 2009; 39: 81-7)

• Journal of ILASS-Korea
• /
• v.17 no.2
• /
• pp.86-93
• /
• 2012

The effects of projectile impact system on the transient spray characteristic which is supersonic liquid tip velocity were studied by experimentally. Supersonic liquid jets were generated by impact of a high speed projectile driven by a Two-stage light gas gun. A high speed camera and schlieren optical system were used to capture the spray structures of the supersonic liquid jets. In a case of nozzle assembly Type-A, expansion gases accelerate a projectile which has a mass of 6 grams from 250 m/s at the exit of the launch tube. Accelerated projectile collides with the liquid storage part, then supersonic liquid jets are injected with instantaneous spray tip velocity from 617.78 m/s to 982.54 m/s with various nozzle L/d. However, In a case of nozzle assembly Type-B which has a heavier projectile (60 grams) and lower impact velocity (182 m/s), an impact pressure was decreased. Thus the liquid jet injected at 210 m/s of the maximum velocity did not penetrate a shock wave and fast break-up was occurred. Pulsed injection of liquid column generated second shock wave and multiple shock wave.

• Journal of Korean Society of Forest Science
• /
• v.86 no.3
• /
• pp.378-390
• /
• 1997

Ten total populations of Korean fir (Abies koreana Wilson) and Manshurian fir [A. nephrolepis (Traut.) Maxim.] were sampled from south Korea to investigate patterns of intraspecific variation in these species and to evaluate a recognition of the two species. Principal components analysis and cluster analysis were performed both on seed-cone data and on needle morphology data. The characters that contributed most to the separation between A. koreana and A. nephrolepis along three principal components axis were leaf width, length of seed, width of seed wing, length of seed wing, cone width, width of scale, and length of bract tip, but these characters were not diagnostic because of overlap in reality. Therefore, all these characters were not reliable in distinguishing these two taxa including bract position (exerted and recurved vs. exerted and straight). The individuals of A. koreana from Mt. Chi-ri appeared quite unique probably on account of its larger cone size and longer scale tip, while those from Mt. Hal-la of A. koreana were generally distinct from others in terms of their larger seed and seed wing and longer scale width. The Mt. Duk-yu specimens of A. korecana appeared somewhat smaller but more data were needed due to the small sampling size. Generally, the gradual clinal geographic trends made evident by the position of resin ducts in leaves of A. koreana can be detected. The southern populations, Mt. Hal-la (an insular population) were generally distinct from the northern populations (Mt. Chi-ri, Mt. Ga-ya and Mt. Duk-yu) in terms of their position of resin duct (medial, within mesophyll vs marginal, close to epidermis : 100% vs 75 or 50%). Although no sharp boundary separating these two species could be detected based on cone and needle morphology, the observed clinal pattern was distinct in northern populations of A. koreana and southern population of A. nephrnlepis. In a preceding study of the flavonoids variation of 20 species in eastern Asia, flavanone (5-deoxyflavanone) was found to be characteristic of A. faxoniana Rehder et Wilson, A. georgei Orr of China and A. koreana of Korea. A. faxoniana, which is assumed to be primitive species, has position of resin duct relative to both the medial and the marginal, while A. georgei and A. koreana are identified by marginal position of resin duct. With respect of foliar flavonoids chemistry, A. koreana was distinct from A. nephrolepis : the southmost samples (Mt. Hal-la and Mt. Chi-ri) contained additional flavonoids derivatives (mainly flavanone) that were not found in the northmost samples of A. nephrolepis except a few individuals from Mts. Seo-rak and Tae-bak populations of Kwang-won province. The presence of A. koreana type flavonoids in two Chinese species suggested that position of resin duct may be a phyletic character. Abies koreana including two Chinese taxa, exhibited the most elaborate and specialized flavonoids profile within the Abies in eastern Asia. Contrary to our initial expectations, the apparent intermediates between A. nephrolepis and A. koreana in Duk-yu and Ga-ya mountains were found. The pattern of variation on position of resin duct and flavonoids chemistry in these populations of A. kareana suggested that genetic interchange or natural hybridization had occurred between these two species. The evidence needed to resolve the status of this taxon is still inconclusive in our opinion until intermediate individuals from Mts. Duk-yu and Ga-ya show indication of hybridization between the two species.