• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.651-659
• /
• 2009

This study dealt with the behavior of pile-abutment joints in integral abutment bridges. Two types of pile-abutment joints were proposed to strengthen its rigid action. One was fabricated with transverse rebars which penetrated the H-pile in the abutment. The other was composed of stud shear connectors on the flanges of the H-pile. Three half scaled pile-abutment joint specimens were fabricated and loading tests were performed to evaluate the behavior of proposed joints. The results showed that the initial stiffness in elastic region of all specimens was sufficient to be applied for the integral abutment bridges. However, the performances of the proposed joints were shown to be more effective in rigid action compared to the joints types suggested by the Integral Bridge Design Guideline. The results from stiffness, strength, rotation and crack propagation tests supported this matter.

• The Journal of Korean Physical Therapy
• /
• v.30 no.4
• /
• pp.135-140
• /
• 2018

Purpose: This study aimed to determine the appropriate stimulus strength that could result in a positive effect on the ankle joint spasticity when patients with chronic stroke performed whole body vibration (WBV) exercise. Methods: Among 72 patients who were diagnosed with stroke at least 6 months ago, those able to perform a half squat pose with ambulation issues due to ankle joint spasticity (modified Ashworth scale, $MAS{\geq}2$) were included for analysis. Individuals participated in four different frequencies of vertical WBV exercise; 0 Hz, 10 Hz, 20 Hz, and 30 Hz. Vibration amplitude was 3-4 mm and 5 minutes WBV exercise was performed at each frequency, followed by a measurement after 2-minute rest. We assigned 18 individuals to each frequency and asked them to participate in the WBV exercise once every 3 weeks. The level of spasticity was evaluated by visual analogue scale (VAS) for self-assessment. The myoton PRO was utilized to objectively evaluate the level of spasticity and check the muscle tone and stiffness. Results: Participants showed 0 Hz VAS was a significant difference between 20 Hz application conditions (p<0.05). Muscle tone was significantly different at 0 Hz between 20 Hz, and 30 Hz (p<0.05), significantly difference at 10 Hz between 30 Hz (p<0.05). Muscle stiffness significantly difference at 0 Hz between 20 Hz, and 30 Hz (p<0.05), significantly difference at 10 Hz between 20 Hz, and 30 Hz (p<0.05). Conclusion: Findings of this study show that the frequency of more than 20 Hz was effective in improving the ambulatory ability in patients with chronic stroke. Currently, the effective WBV protocol is limited. Hence, this study was designed to suggest an effective WBV protocol to improve neuromodulation ability for chronic stroke patients.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.85-94
• /
• 1996

This paper investigated structural behaviors of joint of concrete filled steel tube column and P.C reinforced concrete beam through a series of hysteretic behavior experiment. The results are summarised as follows: (1) The joint stiffness of concrete filled square steel tube column and P.C reinforecd beam was higher than that of concrete filled circular steel tube column and P.C reinforecd beam, and it was decreased as the increase of the number of hysteretic cycle. (2) The aspects of the hysteretic behavior in the joint was stable as the increase of the number of hysteretic cycle, and rotation resisting capacity of joint of concrete filled square steel tube column and P.C reinforced concrete beam was higher than those of the concrete filled circular steel tube column and P.C reinforced concrete beam. (3) Some restriction must be put upon the ratio of axial force in this joint model because the load carrying capacity was decreased by flexural and flexural-torsional buckling in case of the ratio of axial force 0.6. (4) The emprical formula to predict the ultimate capacity of joint model to superimpose shearing strength of steel web(H section) and bending strength of reinforced concrete beam was expected.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.5 s.78
• /
• pp.569-580
• /
• 2005

The postbeam joint connection of the existing steel structure moment flexible frame system did not produce sufficient seismic resistance during the earthquakes in Northridge and Kobe, and it sustained brittle fracturing on the joint connection. This study was performed to execute the high-tensile bolt share connection of H-beams web and the full-scale experiment as a parameter of the existing reinforcement of H-flange rib, by making the shape of the existing joint connection. This experiment was performed to determine the extent of the decrease of the number of high-tensile bolts and how to improve workability of the two-phase shear connection of web beam. In addition, this study was performed to enhance the seismic resistant capacity through the enforcement of rib plates. As a result of the experiment of two-phase shear connection of H-beam web and of joint connection to be reinforced by rib plates, the results of this study showed that the initial stiffness, energy-dissipation capacity, and rotational capacity of plasticity was higher than the existing joint connection. As to the rate of increasing the strength and deformation capacity, there were differences between the tension side and compression side because of the position of shear tap. However, as a whole, they have shown excellent seismic resistant capacity. Also, all the test subjects exceeded 4% (rate of delamination), about 0.029 rad (total plastic capacity), and about 130% (maximum strength of joint connection) of fully plastic moment for the original section. Accordingly, this study was considered as it would be available in the design more than the intermediate-level of moment flexible frame.

• Journal of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.833-840
• /
• 2008

The time and cost can be reduced when applying partial precast concrete to the stair system in comparison to the cast-in-place or precast method. Because the performance of staircase which is used for evacuation can be largely different from connection types of precast concrete member, we tried to know structural behavior and performance evaluation according to each type of stair joints by experimental study. In the cast-in-place rigid joint, much reinforcement is needed in the end portion because much stress is concentrated in the middle portion. Also, in the pin joint which is used in the connection point, the maximum stress occurs in the middle point, so not only the amount of re-bar is increased but also the serviceability is largely decreased. The bolt type of semi-rigid joints proposed in this study had been increased strength and serviceability which is similar to the rigid joints. Also, its ductility was shown about 0.7 times in comparison to the rigid type and was about 2.8 times for the pin joint type. According to the classification of joint in Eurocode, it can be considered that it is one of the semi-rigid joints which are in the semi-rigid-full strength, and the structural behavior can be expected by using a model which applied to stiffness value decreased by 40 percent.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.3
• /
• pp.31-41
• /
• 2006

The scale effect of specimens on the shear behavior of joints is studied by performing direct shear tests on six different sizes in Granite. The peak and residual shear stress, shear displacement, shear stiffness, and dilation angle are measured with the different normal stress(0.29~2.65MPa) and roughness parameters. It is also shown that both the joint roughness coefficient(JRC) and the joint compression strength(JCS) reduce with increasing joint length. A series of shear tests show about 56~67% reduction in peak shear stress, and about 18~44% in residual shear stress, respectively as the contact area of joint increases from 12.25 to $361cm^2$. Also the variation of dilation angle is $27^{\circ}$ at normal stress of 0.29 MPa and $6^{\circ}$ at normal stress of 2.65 MPa, respectively. The envelopes considering scale effect for JRC are made for the peak shear strength of rock joint in comparison with the Barton's equation.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.145-154
• /
• 2005

Love wave and Rayleigh wave are the major elastic waves belonging to the category of the surface wave. Those waves are used to determine the ground stiffness profile using their dispersion characteristics. The fact that Love wave is not contaminated by P-wave makes Love wave superior to Rayleigh wave and other body waves. Therefore, the information that Love wave carries is more distinct and clearer than that of others. Based on theoretical research, the joint inversion analysis that uses the dispersion information of both Love and Rayleigh wave was proposed. This analysis consists of the forward modeling using transfer matrix, the sensitivity matrix for evaluating the ground system and DLSS (Damped Least Square Solution) as an inversion technique. The technique of joint inversion uses the dispersion characteristics of Love wave and Rayleigh wave simultaneously making the sensitivity matrix. The sensitivity matrix was used for inversion analysis repeatedly to find the approximate ground stiffness profile. The purpose of the joint inversion analysis is to improve accuracy and convergency of inversion results by utilizing that frequency contribution of each wave is different.

• Journal of Korean Foot and Ankle Society
• /
• v.6 no.1
• /
• pp.73-79
• /
• 2002

Purpose: To evaluate the effectiveness of callotasis using the external fixator for the treatment of brachymetatarsia. Materials and Methods: Eleven patients(15 cases) who underwent callotasis were available. Follow-up averaged 23 months(15-38 months). Both the patients' postoperative satisfaction and the postoperative radiographic results were retrospectively evaluated. Results: The duration from applying the external fixator to remove averaged 15 weeks (8-21 weeks). We did osteotomy again in two cases because of early consolidation at the osteotomy site during distraction period. All cases were evaluated mild claw toe deformity and motional pain in metatarsophalangeal joint, but all patients satisfied the postoperative results except one complained motional pain and stiffness in metatarsophalangeal joint. The metatarsal shortening averaged 13mm(9-18mm) before operation. The amount of distraction for shortened metatarsals averaged 15mm(5-22mm). We found the 6 cases of narrowing of the metatarsophalangeal joint, 2 cases of subluxation of the metatarsophalangeal joint. Conclusion: We think that callotasis with external fixator is good operative method for the brachymetatarsia.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.382-392
• /
• 2004

The usage of constant velocity (CV) joint is effective for motorboats on gliding regime of the motion. During transition on the gliding when angle of the CV differs from null on driving and driven composite shafts there are moments of the second order. Excitation of oscillations of the second order moments occurs when driving shafts transmits a variable torque. which generates through CV joint a lateral moment acting on the bearing. As a result of oscillations from a resonating harmonic of a shafting the harmonic with the greater or periodically varying amplitude for power condition trough transferring to nominal power 144kW. Beating conditions coincide with third mode having frequency 45.486 Hz. In that case there is high increasing of the equivalent stresses. The forming of the stiffness of the composite material is concerned to use most orientation of the layer angle in the range of $\pm$60 degrees relatively of shaft axis. Application of that angles for layer orientation gives possibility to avoid high disturbance of the shafting for motorboat transition regime.

• Steel and Composite Structures
• /
• v.38 no.5
• /
• pp.547-562
• /
• 2021

This paper aims to explore the mechanical behavior and moment-rotation model of blind bolted joints between concrete-filled double skin steel tubular columns and steel-concrete composite beams. For this type of joint, the inner tube and sandwiched concrete were additionally identified as basic components compared with CFST blind bolted joint. A modified moment-rotation model for this type of connection was developed, of which the compatibility condition and mechanical equilibrium were employed to determine the internal forces of basic components and neutral axis. Following this, load transfer mechanism among the inner tube, sandwiched concrete and outer tube was discussed to assert the action area of the components. Subsequently, assembly processes of basic coefficients in terms of their stiffness and resistances based on the component method by simplifying them as assemblages of springs in series or in parallel. Finally, an experimental investigation on four substructure joints with CFDST columns for validation purposes was carried out to capture the connection details. The predicted results derived from the mechanical models coincided well with the experimental results. It is demonstrated that the proposed mechanical model is capable of evaluating the complete moment-rotation relationships of blind bolted CFDST column composite connections.