• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.411-412
• /
• 2006

A high nitrogen PM tool steel has shown to have an excellent galling resistance due to the introduction of a high amount of a low friction phase predominantly consisting of VN. Tool making and heat treatment are according to standard procedures. An increase of tool life of more than two times compared to ordinary tool steels is found. Furthermore, the new low friction tool steel shows a potential for sintered parts with higher densities through the applica bility of increased compaction pressure or minimized lubricant amount.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.855-860
• /
• 2001

As being inconvenient to apply reinforced concrete structure to high-rise buildings. it is applied steel structured system. Therefore light-weight wall systems are applied as partition wall to reduce the self-load of the building. But. the required performances of a light-weight wall are not evaluated systematically. As a field survey result. partition walls of house-to-house and room-to-room were not showed their respected performances. so the dwellers are feel so worse the quality of the whole building. In steel-structured high-rise buildings especially. occupant's dissatisfaction concerned indoor noise was high because curtain wall systems having a high air-tight performance isolate the outdoor noise making masking effect. Also to suppress indoor air movement. stact effect must be concerned. Therefore wall systems which have high performances of sound insulation and air-tightness are required in high-rise buildings.

• Structural Monitoring and Maintenance
• /
• v.5 no.4
• /
• pp.429-443
• /
• 2018

Fatigue is a principal failure mode for steel structures, and it is still less understood than any other modes of failure. Fatigue life estimation of metal bridges is a major issue for making cost effective decisions on the rehabilitation or replacement of existing infrastructure. The fatigue design procedures given by the standard codes are either empirical or based on nominal stress approach. Since the fatigue life estimation through field measurements is difficult and costly, more researches are needed to develop promising techniques in the fatigue analysis of bridges through Finite Element Analysis (FEA). This paper aims to develop a methodology for the Fatigue life estimation of railway steel bridge using FEA. The guidelines of IIW-1823-07 were used in the development of the methodology. The Finite Element (FE) package ANSYS and the programming software MATLAB were used to implement this methodology on an Indian Railway Standard (IRS) welded plate girder bridge. The results obtained were compared with results from published literature and found satisfactory.

• Structural Engineering and Mechanics
• /
• v.70 no.3
• /
• pp.303-310
• /
• 2019

Any revision of seismic codes usually demands a higher capacity from structural members, making existing structures unsafe particularly from strength considerations. Retrofitting of capacity deficient members is very suitable for tackling such situations. This paper presents an experimental study on different retrofitting measures adopted for strengthening a series of reinforced concrete (RC) beams. Four identical RC beam specimens were casted, out of which three specimens were strengthened by different schemes (viz., bolted hot rolled flat, bolted cold-formed steel channel, and carbon fibre reinforced polymer (CFRP) laminate, respectively) on their tension face and tested under four-point monotonic loading. This study focuses on the investigation of the flexural behaviour of these retrofitted beams, observed in terms of strength and stiffness. It was concluded that all retrofitting measures improved the structural performance of these beams. However, the cost involved with each strengthening mode was proportional to the improvement in the performance achieved.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.479-486
• /
• 2009

This paper presents an integrated real-time monitoring and control framework that facilitates decision making by enabling project managers to take corrective actions right after any deviation happens and mitigate the damage to the ongoing steel projects. The proposed framework employs the High Level Architecture (HLA) as its infrastructure. It is composed of several individual monitoring and control components called "Federates," which cooperate and interact with each other through the Real-time Infrastructure (RTI). Reusability, interoperability and extendibility of federates in the proposed project control system make this a unique system.

• Architectural research
• /
• v.12 no.2
• /
• pp.85-92
• /
• 2010

In recent years, construction projects have been forced to cope with lack of skilled labor and increasing hazard circumstance of human operations. A construction robotic system has been frequently accomplished as one alterative for overcoming these difficulties in increasing construction quality, enhancing productivity, and improving safety. However, while the complexity of such a system increases, there are few ways to carry out an assessment of the system. This paper introduces a knowledge-based multi-criteria decision-making process to assist decision makers in systematically evaluating an automated system for a given project and quantifying its system performance index. The model employs linguistic terms and fuzzy numbers in attempts to deal with the vagueness inherent in experts' or decision makers' subjective opinions, considering the contribution resulted from their knowledge on a decision problem. As an illustrative case, the system, called Robotic-based Construction Automation, for constructing steel erection of high-rise buildings was applied into this model. The results show the model's capacities and imply the application to other extended types of construction robotic systems.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.35-39
• /
• 2014

Window roller housings are durable because high-quality source materials such as stainless steel is used in making them. After a series of precise structure analysis, their design is optimized. They are subject to repetitive driving tests of more 100,000 times, durability tests, impact resistance tests, corrosion tests and others. For a long time, gaps often occur in press molded products owing to serious squareness deformation and flatness deformation of them. Severe burrs in press molded products require frequent grinding, which leads to short life cycle and rough or unreliable movement of assembled roller housing, which, in turn, causes product defects. This study focuses on developing measures to resolve existing defects and to improve lifespan of dies by designing and making a window roller shearing die.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.616-619
• /
• 2002

Spin casting is one of useful methods to manufacture metal parts with low mold cost and short delivery time. But the silicon rubber based conventional method has several problems such as poor dimensional accuracy, limitation in casting materials and its dependency on speciality in meld making process. To solve those problems, this paper suggests a steel based mold making method using direct CNC machining and the experimental results shows that the parts from the developed method has better dimensional accuracy and surface roughness than those from the conventional method.

• Journal of Energy Engineering
• /
• v.6 no.2
• /
• pp.152-161
• /
• 1997

Blending various coals during the coke making process affects the quality of coke as well as the total energy required for the process. The mathematical model based on Merrick's work developed to predict the effect of blending coals on coke making process. The Crank-Nicholson method was used to solve the model equation to predict temperature distributions, a coking time, and a total energy required during the process. The developed model successfully applied to Kwang-Yang Steel Company's coke oven to validate the model performance. It is hoped that the model can serve as a guidelines on how to blend coals during the process.

• Journal of Power System Engineering
• /
• v.8 no.3
• /
• pp.30-35
• /
• 2004

In the steel making industries, the continuous casting process has been applied to the number of company because of its economical benefit. Casting rolls are utilized for frictional drive and transport of solidifying slap. Dimensional tolerances, mechanical stability and surface condition of the cast roll can affect both the surface and internal quality of the product being cast. To overcome these problems, the industry is accelerating on the rate of technology improvements. Samples were overlaid on the S45C steel by submerged arc welding process. And the hardness, wear, electrochemical corrosion and oxidation tests were carried out. Test results were that all these materials were satisfying basic requirements of caster rolls. By these results, the addition of 0.1%Nb and 0.15%V increase mechanical properties and tempering resistance by its superior carbide forming characteristics in low carbon $12{\sim}13%Cr$ martensitic stainless steels.