• 한국구조물진단유지관리공학회 논문집
• /
• 제27권1호
• /
• pp.78-85
• /
• 2023

이 연구는 하이브리드 섬유시트를 이용하여 보강된 철근콘크리트 기둥의 구조성능평가에 관한 연구이다. 내진보강 공법은 보강이 필요한 노후 콘크리트 구조물에 아라미드섬유와 PET섬유를 일축으로 배열하여 직조한 하이브리드 섬유시트를 에폭시로 함침하고, 이를 구조물에 부착시켜 보강 구조물의 내하력을 증진시키는데 그 목적이 있다. 특히, 강재보다 가벼운 섬유를 사용함으로써 얻어지는 재료의 경량화뿐만 아니라, 사용된 섬유 중 저강도 고인성의 섬유요소가 고강도 저인성 섬유요소의 취성적 파괴를 지연시켜 기존의 섬유보강 공법과 비교해 안전성 측면에서 우수하다. 연구는 구조실험과 그 결과에 대한 구조성능평가로 진행되었다. 총 4개의 실험체는 하이브리드 보강방법 및 파괴모드를 주요변수로 계획하였으며, 실험체 크기 및 가력조건 등은 기존연구에서 수행한 실험결과와 비교가 가능하도록 계획하였다. 실험체의 구조성능은 에너지소산능력, 연성평가등을 사용하여 평가하였다. 다음과 같은 분석을 통하여 하이브리드 섬유시트의 보강하였을 때 우수한 성능 결과를 보일 수 있다는 결론은 얻었다.

• 콘크리트학회논문집
• /
• 제12권3호
• /
• pp.67-75
• /
• 2000

It was well recognized that the damages associated mainly with the aging of civil infrastructures were one of very serious problems for assurance of safety and reliability. Recently carbon fiber sheet(CFS) has been widely used for reinforcement and rehabilitation of damaged concrete beam. However, the fundamental mechanism of load transfer and its load-resistant for carbon fiber sheet reinforced concrete are not fully understood. In this study, three point bending test has been carried out to understand the damage progress and the micro-failure mechanism of CFS reinforced mortars. For this purpose, four different types of specimens are used, that is, mortar, steel bar reinforced mortar, CFS reinforced mortar, and steel bar and CFS reinforced morter. Acoustic Emission(AE) technique was used to evaluate the characteristics of damage progress and the failure mechanism of specimens. in addition, two-dimensional AE source location was also performed to monitor crack initiation and propagation processes for these specimens.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.69-77
• /
• 2000

The reinforced concrete(RC) flexural members strengthened with steel plate/CFS at soffit have initial stresses and strains in reinforcements and concrete caused by the service loads at the time of retrofitting works. These initial residual stresses and strains of strengthened beams may affect the flexural performance of the rehabilitated beams. The objective of this study is to evaluate and verify the effectiveness of rehabilitation by external bonded steel plates and CFS to the tension face of the beams under three conditions of pre-loading. Thirteen beam specimens are tested and analyzed. Main test parameters are pre-loading conditions, strengthening materials and reinforcement ratio of specimens. The effect of test parameters on the strengthened beams is analyzed from the maximum load capacity, load-deflection relationship, state of stress of the materials. crack propagation phase, and failure modes. Both test results and design formulas of ACI Code provisions are compared and evaluated.

• Steel and Composite Structures
• /
• 제15권4호
• /
• pp.451-466
• /
• 2013

This paper deals with the multi-objective optimization of tire reinforcement structures such as the tread belt and the carcass path. The multi-objective functions are defined in terms of the discrete-type design variables and approximated by artificial neutral network, and the sensitivity analyses of these functions are replaced with the iterative genetic evolution. The multi-objective optimization algorithm introduced in this paper is not only highly CPU-time-efficient but it can also be applicable to other multi-objective optimization problems in which the objective function, the design variables and the constraints are not continuous but discrete. Through the illustrative numerical experiments, the fiber-reinforced tire belt structure is optimally tailored. The proposed multi-objective optimization algorithm is not limited to the tire reinforcement structure, but it can be applicable to the generalized multi-objective structural optimization problems in various engineering applications.

• 한국해양공학회지
• /
• 제15권1호
• /
• pp.98-103
• /
• 2001

This paper is conducted to compare the seismic design standard of a bridge column such as the Korean Bridge Design Standard(KBDS), EC 8, NZS 3101 and ATC 32. The KBDS adopted the seismic design requirements in 1992. The earthquake magnitude in Korea is compared with those in the west coast of the USA. It may be said that the current seismic design requirements of the KBDS provides design results, that are too conservative especially for transverse reinforcement details and amounts in reinforced concrete columns. This fact usually creates construction problems in concrete casting, due to congestion of transverse reinforcement. Furthermore, the effective stiffness; $I_{eff}$ depends on both the axial load P/$A_gF_{ck}$ and the longitudinal reinforcement ratio $A_{st}/A_g, so it is the conservative to use the effective stiffness I$_{eff}$ than the gross section stiffness Ig. Seismic design for the transverse reinforcement content of the concrete column was analyzed and considered to have an extreme-fiber compression strain, response modification factor, axial load and effective stiffness etc.c.

• Structural Monitoring and Maintenance
• /
• 제7권3호
• /
• pp.167-193
• /
• 2020

In this paper, the behavior of interior steel fiber reinforced concrete beam - column joints (BCJs) under cyclic loading is investigated. An experimental program including tests on twelve reinforced concrete (BCJs) specimens under cyclic loading was carried out. The test specimens are divided into two groups having different geometry: group (G1) (symmetrical BCJs specimens) and group (G2) (nonsymmetrical BCJs specimens). The parameters considered in this study are the steel fibers (SFs) content by volume of concrete (V_f), the spacing of shear reinforcement at the joint region, and the area of longitudinal flexural reinforcement. Test results show that the addition of 0.5% SFs with stirrups spacing S=S_max has effectively enhanced the overall performance of BCJs with respect to energy dissipation, ductility ratio, spreading and width of cracks. The failure of specimens is governed mainly by the formation of a plastic hinge at the face column and outside the beam-column junction. Secondary shear cracks were also observed in the beam-column junctions.

• Structural Engineering and Mechanics
• /
• 제24권5호
• /
• pp.561-584
• /
• 2006

The paper presents results of parametric studies, and an overall approach for the design of a modular bridge system which incorporates a steel-reinforcement free concrete slab cast on top of carbon FRP stiffened deck panels which act as both structural formwork and flexural reinforcement, spanning between hollow box type FRP girders. Results of the parametric studies are highlighted to elucidate important relationships between critical configurational parameters and empirical equations based on numerical studies are presented. Results are discussed at the level of the individual deck and girder components, and as a slab-on-girder bridge system. An overall design methodology for the components and bridge system including critical performance checks is also presented.

• Computers and Concrete
• /
• 제13권2호
• /
• pp.255-270
• /
• 2014

Impact performance of high-performance concrete (HPC) and SFRC at 28-day and 56-day under the action of repeated dynamic loading was studied. Silica fume replacement at 10% and 15% by mass and crimped steel fiber ($V_f$ = 0.5%- 1.5%) with aspect ratios of 80 and 53 were used in the concrete mixes. Results indicated that addition of fibers in HPC can effectively restrain the initiation and propagation of cracks under stress, and enhance the impact strengths and toughness of HPC. Variation of fiber aspect ratio has minor effect on improvement in impact strength. Based on the experimental data, failure resistance prediction models were developed with correlation coefficient (R) = 0.96 and the estimated absolute variation is 1.82% and on validation, the integral absolute error (IAE) determined is 10.49%. On analyzing the data collected, linear relationship for the prediction of failure resistance with R= 0.99 was obtained. IAE value of 10.26% for the model indicates better the reliability of model. Multiple linear regression model was developed to predict the ultimate failure resistance with multiple R= 0.96 and absolute variation obtained is 4.9%.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권3호
• /
• pp.76-83
• /
• 2014

본 연구의 목적은 고강도 SFRC 보의 강섬유 보강효과를 평가하기 위한 것이다. 이를 위하여 13개의 실험체를 제작하여 성능실험을 실시하였다. 실험 변수는 전단경간비, 강섬유 혼입률, 전단보강근비이며 콘크리트 강도는 60 MPa이다. 기존 연구결과와 재료 및 부재 실험결과에 대한 분석에 의하면, 전단경간비 2.5와 강섬유 혼입률 1.0%인 경우가 강섬유 보강효과가 최대로 발휘되는 것으로 평가되었다. 강섬유 보강 및 전단경간비를 고려한 기존 전단내력식은 고강도 SFRC보의 내력을 과소평가하는 것으로 평가되었다. 향후 고강도 SFRC 보의 강도특성에 대한 보완 연구가 필요한 것으로 판단된다.

• 콘크리트학회논문집
• /
• 제20권2호
• /
• pp.257-267
• /
• 2008

본 연구에서는 강섬유보강 콘크리트 휨부재에 적용할 수 있는 휨강도 산정식과 전단강도 제안식을 분석하였으며, 보다 정확성과 안전성이 향상된 전단강도 산정식이 필요한 것으로 판단되어 새로운 전단강도 제안식을 도출하였다. 휨강도 산정식은 휨파괴한 36개의 실험체를 대상으로 검토해본 결과 기존의 콘크리트보에서 무시되는 콘크리트의 인장강도를 고려하는 것이 타당한 것으로 나타났으며, 제안된 휨강도 약산식은 실험 결과와 공칭휨강도 산정식과 비교할 때 양호한 수준의 강도 예측이 가능하다고 사료된다. 또한 본 연구에서 제안한 전단강도 산정식과 기존 연구자의 전단강도 제안식을 전단파괴한 실험체의 최대강도와 비교, 검토한 결과에 의하면, 본 연구의 제안식이 정확성과 안전성을 모두 확보하면서 전단강도를 예측하는 것으로 평가되었다.