• Structural Engineering and Mechanics
• /
• v.58 no.2
• /
• pp.327-345
• /
• 2016

Many experimental and analytical studies have been conducted with beam-column subassemblages composed of a two-span beam to investigate the progressive collapse resistance of RC frames. Most study results reveal a strength-decreased transition phase in the nonlinear static load-deflection curve, which may induce dynamic snap-through response and increase the chord rotation demand for effective catenary action (ECA). In this study, the nonlinear static response is idealized as a piecewise linear curve and analytical pseudo-static response is derived for each linearized region to investigate the rotation demands for the ECA of the two-span RC beams. With analytical parameters determined from several published test results, numerical analysis results indicate that the rotation demand of 0.20 rad recommended in the design guidelines does not always guarantee the ECA. A higher rotation demand may be induced for the two-span beams designed with smaller span-to-depth ratios and it is better to use their peak arch resistance (PAR) as the collapse strength. A tensile reinforcement ratio not greater than 1.0% and a span-to-depth ratio not less than 7.0 are suggested for the two-span RC beams bridging the removed column if the ECA is expected for the collapse resistance. Also, complementary pseudo-static analysis is advised to verify the ECA under realistic dynamic column loss even though the static PAR is recovered in the nonlinear static response. A practical empirical formula is provided to estimate an approximate rotation demand for the ECA.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.3
• /
• pp.137-147
• /
• 1997

Interface shear strength of' concrete under static loading and deterioratiion of interface strength by fatigue loading in shear were experimentally investigated using composite beam test specimens. Thirteen beams were constructed. Five composite beams were tested statically until interface delaminations were observed in the static tests. Seven composite beam and one monolithically cast beam were subjected to two to three million cycles of fatigue load. Test variables were interface roughness, interface shear reinforcement, and presence of interface bond. The average interface shear strength of the composite beams with bonded-rough interface was 6, 060 kPa. No interface delamination was observed after cycling for the composite beams with bonded - rough interface and interface bond was not influenced by repeated application of the shear stress of 2.000 kPa(about 1/3 of the static interface shear strength). Smooth interface and unbonded-rough interface with shear reinforcement deteriorated under repeated shear loading.

• Journal of the Korea Furniture Society
• /
• v.11 no.2
• /
• pp.45-53
• /
• 2000

This study was carried out to determine the suitability of 3 months old bamboo species of Phyllostachys bambusoides S. et Z., Phyllostachys Pubescens Mazel and Phyllostachys nigra var henonis Stapf as raw materials for the manufacture of strandboard. Total of 108 strandboards were made using urea-formaldehyde resin content level of 12% and one percent of liquid wax emulsion. The strandboard consisted of three layers the top and the bottom layer of which were oriented to the same direction and weighted 25% of the strandboard each. The middle core layer weighed 50% of the board and was perpendicular to the outer top and bottom layers. Analysis was performed to determine the effect of strand lengths and Uowing years of 3 months, 2 years and 3 years on strandboard properties. The physical and mechanical properties of bamboo species and boards were measured and compared to the standard requirements of strandboards. The results are as follows; 1. The more the growing years the higher the density of bamboo. Top part of bamboo indicated higher density value than that of bottom part. 2. Bamboo showed higher static bending strength compared to the main wood species. Longer growing years of bamboo generally inclosed the static tending strength out there were no statistical significancies for Phyllostachys bmbusoides S. et Z. and Phyllostachys pubescens Mazel. 3. Strand length indicated no difference on density and moisture content of strandboard. 5 cm of strand length gave the best static bending strength and internal bonding strength. Bamboo strandboard exhibited lesser extents of thickness swelling than that of CSA standard. 4. 3 months old bamboo gave higher static bending strength of strandboard than those of 2 years and 3 years old bamboo. In case of Phyllostachys nigra var henonis Stapf, 3 months old bamboo indicated higher internal bonding strength than those of 2 years and 3years old bamboo. but in Phyllostachys bambusoides S. et Z., Phyllostachys pubescens Mazel, there were no difference among growing years. Growing years showed no different physical properties of bamboo strandboard.

• Physical Therapy Korea
• /
• v.22 no.4
• /
• pp.8-16
• /
• 2015

The purpose of this study was to evaluate the effects of mobilization of the sciatic nerve on hamstring flexibility, lower limb strength, and gait performance in patients with chronic stroke. This study was a randomized clinical trial with a crossover design. Sixteen subjects were recruited for this study. The subjects were randomly divided into two intervention groups and underwent either of the following two interventions: sciatic nerve mobilization or static stretching of the hamstring. We assessed hamstring flexibility, lower limb strength, and gait performance using a digital inclinometer, a hand-held dynamometer, and the 10-meter walk test, respectively. Subjects had a 24-hour rest period between each session in order to minimize carryover effects. Measurements for each test were assessed prior to and immediately after the intervention sessions. Using a two-way analysis of variance test with repeated measures, data from the two trials were analyzed by comparing the differences between both techniques. The level of statistical significance was set at .05. Sciatic nerve mobilization resulted in significantly better knee extensor strength (p=.023, from $15.32{\pm}5.98$ to $18.16{\pm}6.95kg$) and knee flexor strength (p=.011, from $7.80{\pm}4.80$ to $8.15{\pm}4.24kg$) in the experimental group than in the control group. However, no significant effects of static stretching of the hamstring were observed on hamstring flexibility from the ankle plantar flexion (p=.966) and ankle neutral positions (p=.210) and on gait performance (p=.396). This study indicated that the sciatic nerve mobilization technique may be more effective in muscle activation of the knee extensor muscle and knee flexor muscle than hamstring static stretching technique in patients with chronic stroke.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.2
• /
• pp.115-121
• /
• 2015

PURPOSE. This study aimed to evaluate the effect of implant thread depth on primary stability in low density bone. MATERIALS AND METHODS. The insertion torque was measured by inserting Ti implants with different thread depths into solid rigid polyurethane blocks (Sawbones) with three different bone densities ($0.16g/cm^3$, $0.24g/cm^3$, and $0.32g/cm^3$). The insertion torque value was evaluated with a surgical engine. The static compressive strength was measured with a universal testing machine (UTM) and the Ti implants were aligned at $30^{\circ}$ against the loading direction of the UTM. After the static compressive strength test, the Ti implants were analyzed with a Measurescope. RESULTS. The Ti implants with deeper thread depth showed statistically higher mean insertion torque values (P<.001). Groups A and group B had similar maximum static compressive strengths, as did groups C and D (P>.05). After the static compressive strength, the thread shape of the Ti implants with deeper thread depth did not show any breakage but did show deformation of the implant body and abutment. CONCLUSION. The implants with deeper thread depth had higher mean insertion torque values but not lower compressive strength. The deep threads had a mechanical stability. Implants with deeper thread depth may increase the primary stability in areas of poor quality bone without decreasing mechanical strength.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.5
• /
• pp.429-440
• /
• 2002

Current dental restorations present a relatively weak resistance to fracture. Owing to their unique mechanical properties, fibre-reinforced polymers are now being considered. Unidirectional or woven continuous fibres, made of glass, polyethylene, carbon or Kevlar, have been evaluated. This study focused on the use of glass fibre knitted fabrics to reinforce acrylate resins, in order to investigate the possibility to construct single crowns as well as three unit bridges. Some points affecting the final composite system were tested ; 1) static strength, with focus on the stress transfer under a occlusal contact point ; 2) modelling of a three nit bridge ; 3) fatigue strength as a posterior three unit bridge material. The study demonstrated that knitted fabric reinforcements are showing an interesting compromise between stiffness, static strength for single crown. For three unit bridge applications in the posterior arch, however knitted glass fabric reinforcements were not strong enough in fatigue An additional reinforcement in the posterior arch fixed partial denture design was recommended.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.6
• /
• pp.47-58
• /
• 2004

As concrete structures are getting larger, higher, longer and more specialized, it is more required to develop steel fiber concrete and apply to the real world. In this research, it is aimed to have fatigue strength examined, varying the steel fiber content of 0%, 0.75%, 1.00%, 1.25% by experimental study of fatigue behavior of the steel fiber reinforced concrete continuous beams under cyclic loading. The ultimate load and initial load of flexural cracking were measured by static test. In addition, the load versus strain relation, load versus deflection relation, crack pattern and fracture mode by increasing weight were observed. On the other hand, the crack propagation and the modes of fracture according to cycle number and the relation of cyclic loading to deflection relation and strain relation were investigated by fatigue test. As the result of fatigue test, continuous beam without steel fiber was failed at 60 ~ 70% of The static ultimate strength and it could be concluded that fatigue strength to two million cyclic loading was arround 67.2% by S-N curve. On the other hand, that with steel fiber was failed at 65 ~ 85% of the static ultimate strength and it could be concluded fatigue strength to two million cyclic loading around 71.7%.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.6
• /
• pp.59-66
• /
• 2001

Fatigue strength of the welding structure is governed by the residual stress at the weldment toe and static tensile overloads were known as relieving the residual stresses. In this study, static tensile overloads were applied to the welding structures which caused the relief of residual stresses. The amount of residual stress relief was found as proportional to the change of fatigue limit at the given conditions. Based on the fact of the proportionality between the change of fatigue limit and that of residual stress, simple measurement technique is proposed. Modified stress-life curves base on proposed technique gave good agreement with test results.

• Journal of the Ergonomics Society of Korea
• /
• v.9 no.2
• /
• pp.3-9
• /
• 1990

The paper concerns with the visual illusion strength for the static and dynamic figures which are generated on computer CRT. The Vertical-Horizontal, Ponzo, and Muller-Lyer illusion are studied under various conditions of type, size, and background angle of figure. And the results are obtained through the Multivariate Analysis of Variance (MANOVA). This paper concludes that the size and background angle of figure generally effect on the visual illusion, and there is a significant difference between figure types. These results can be applied to eliminate the visual illusion in real design.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.11
• /
• pp.1225-1232
• /
• 2009

This study suggests a structural design process for the upper control arm installed at a vehicle. Static strength and durability are the most important responses in the structural design of a control arm. This study considers the static strength in the optimization process. The inertia relief method for FE analysis is utilized to simulate the static loading conditions. According to the classification of structural optimization, the structural design of a control arm is included in the category of shape optimization. In this study, the metamodel technique using the kriging method is adopted to obtain the minimum weight satisfying the strength constraint. Then, the final design is suggested by considering the durability criteria. The durability assessment is obtained by the index of fatigue durability called the SWT (Smith-Watson-Topper) index. The final optimum shape has been proposed by trial and error method.