• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.172-180
• /
• 1995

Isothermal interrupted deformation behavior of 10vol.%SICp/AI-Si composites was investigated by hot torsion test at the temperature ranges from 27$0^{\circ}C$ to 43$0^{\circ}C$ and at strain rate range of 1.26X10-2~2.16X10-1/sec. With increasing pass strain, flow stresses were high compared to continuous deformation condition. Fractional softening was increased with temperature imterruption time and pass strain. Fractional softening of 10vol.%SiCp/AI-Si composites was lower than that of AI-Si matrix at 37$0^{\circ}C$. However at high temperature of 43$0^{\circ}C$, SiC particle promoted static softening, diminishing the dislocation density at the interface of AI-Si matrix and reinforcements, then this resulted in higher fractional softening in composites. Both of failure strain improved reducing the fracture of SiC particle and Si precipitates above 32$0^{\circ}C$, however at low temperature of 27$0^{\circ}C$, the softening effect by interrupted deformation was found to be negligible.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.167-174
• /
• 2006

In this paper, the applicability of strain data to a strain-energy-based damage evaluation methodology in detecting damage in a beam-like structure is demonstrated. For the purpose of this study, one of the premier damage evaluation methodology based on modal amplitudes, the damage index method, is expanded to accomodate strain data, and the numerical and experimental verifications are conducted using numerical and experimental data. To compare the relative performance of damage detection, the damage evaluation using acceleration data is also performed for the same damage scenarios. The experimental strain and acceleration data are extracted from laboratory static and dynamic tests. The numerical and experimental studies show that the strain data as well as acceleration data can be utilized in detecting damage.

• 한국해양공학회지
• /
• 제30권4호
• /
• pp.268-276
• /
• 2016

This paper presents a study on the crashworthiness of the scaled-down stiffened panels used on a Korean icebreaker. In order to validate the crashworthiness of the panels, this paper provides various mechanical properties such as the results of a CVN test, quasi-static tensile test, and high-speed tensile test at arctic temperatures. Two types of steels (EH32 and FH32) were chosen for the material tests. CVN tests revealed that the two steels were equivalent up to −60℃ in terms of their impact energy absorption capacity. However, the toughness of FH32 was significantly superior to that of EH32. EH32 showed slightly higher flow stresses at all temperature levels compared to FH32. The improvement ratios of the yield strengths, tensile strengths, plastic hardening exponents, etc. for FH32, which were obtained from quasi-static tensile tests, showed an apparent ascending tendency with a decrease in temperature. Dynamic tensile test results were obtained for the two temperatures levels of 20℃ and −60℃ with two plastic strain rate levels of 1 s⁻¹ and 100 s⁻¹. A closed form empirical formula proposed by Choung et al. (2011;2013) was shown to be effective at predicting the flow stress increase due to a strain rate increase.

• Steel and Composite Structures
• /
• 제50권6호
• /
• pp.659-674
• /
• 2024

Casting Ultra High-Performance Concrete (UHPC) on an orthotropic steel deck and forming a composite action by connectors could improve the steel deck fatigue performance. This study presents the mechanical performance of a proposed post-combination connection between UHPC and steel, which had a low constraint effect on UHPC shrinkage. A total of 10 push-out tests were conducted for static and fatigue performance investigations. And the test results were compared with evaluation methods in codes to verify the latter's applicability. Meanwhile, nonlinear simulation and parametric works with material damage plasticity models were also conducted for the static and fatigue failure mechanism understanding. The static and fatigue test results both showed that fractures at stud roots and surrounding local UHPC crushes were the main failure appearances. Compared with normally arranged studs, group arrangement could result in reductions of static stud shear stiffness, strength, and fatigue lives, which were about 18%, 12%, and 27%, respectively. Compared with the test results, stud shear capacity and fatigue lives evaluations based on the codes of AASHTO, Eurocode 4, JSCE and JTG D64 could be applicable in general while the safety redundancies tended to be smaller or even insufficient for group studs. The analysis results showed that arranging studs in groups caused obviously uneven strain distributions. The severer stress concentration and larger strain ranges caused the static and fatigue performance degradations of group studs. The research outcome provides a very important basis for establishing a design method of connections in the novel post-combination steel-UHPC composite deck.

• 오토저널
• /
• 제8권3호
• /
• pp.77-87
• /
• 1986

The fatigue characteristic study of a Pony Coil spring is performed by considering the tropical service conditions in the range of 50.deg. C through 150.deg. C. The experiment results of the static and dynamic characteristics of the test pieces agreed with the result of the strain analysis by wittricke's method. The strain energy value is increased as temperature rises. An increase is 1.58% at 100.deg. C and 2.26% at 150.deg. C after fatigue tests. The elastic strain is also decreased as temperature rises.

• International Journal of Safety
• /
• 제2권1호
• /
• pp.1-6
• /
• 2003

In this paper, several different fracture criteria using the Eftis and Subramanian's stress solutions [1] are compared with the printed experimental results under different loading conditions. The analytical results of using the solution with non-singular term show better than without non-singular in comparison with the experimental data. And maximum tangential stress criterion (MTS) and maximum tangential strain energy density criterion (MTSE) can get useful results for several loading conditions.

• 한국철도학회논문집
• /
• 제19권6호
• /
• pp.755-764
• /
• 2016

이 논문에서는, 변위-변형률 관계로부터 변위를 추정하는 선행 연구의 현장 적용성을 검토하기 위하여 실교량에 대한 현장재하실험을 실시하고, 그 결과에 대해 고찰하였다. 3경간 연속 IPC 거더 도로교 및 강합성 박스거더 경량전철 교량에 변위계 및 변형률 게이지를 부착하고, 재하차량에 의한 응답을 측정하였다. 현장재하실험을 통해 얻어진 실측 변형률을 변위로 변환시키기 위해 변위와 변형률의 관계를 이용하였다. 해석적인 방법으로 변위-변형률 관계를 도출하기 위해 연구대상 교량을 격자구조로 모형화하고 구조해석을 수행하였다. 연구결과, 사전 구조해석에 의해 얻어진 변위-변형률 관계와 실측 변형률을 이용하여 변위를 추정하여도 실용상 만족할 만한 결과를 도출할 수 있었다. 이 연구 결과는 향후 계측이 어려운 환경하에 놓여 있는 교량의 변위 측정에 널리 활용될 수 있을 것으로 기대된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.304-309
• /
• 2000

Strain gage method is used to evaluate the mode I dynamic stress intensity factor of marging steel(18Ni) and titanium alloy(Ti-6A1-4V). To decide the best strain gage position on specimen, static fracture toughness test was performed. Then instrumented charpy impact test and dynamic tensile test was performed by using strain gage method for evlauating dynamic stress intensity factor. Strain gage signals on the crack tip region are used to calculate the stress intensity factors. It is found that strain gage method is more useful than method by using load which is obtained from impact tup to assess dynamic characteristics such as dynamic stress intensity factor.

• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.619-628
• /
• 2001

A viscoelastic constitutive equation of rubber is proposed under small oscillatory load superimposed on large static deformation. The proposed model is derived through linearization of Simos nonlinear viscoelastic constitutive model and reference configuration transformation. Statically pre-deformed state is used as reference configuration. The model is extended to a generalized viscoelastic constitutive equation including widely-used Mormans model. Static deformation correction factor is introduced to consider the influence of pre-strain on the relaxation function. The model is tested for dynamic behavior of rubbers with different carbon black fractions. It is shown that the constitutive equation with static deformation correction factor agrees well with test results.

• 소음진동
• /
• 제9권3호
• /
• pp.472-476
• /
• 1999

The effect of static preload on the dynamic properties of rubber materials is rather important, especially when good isolation characteristics are required at high frequencies. However, there are still few papers for dynamic characteristics of compressed rubber components. It was demonstrated in reference (4) that for bonded rubber material of a cylindrical shape, a simplified theory equation between linear dynamic and nonlinear static behavior of rubber material was useful to predict their combined effects. This paper presents the second part of the study. It is confirmed that for the compressed rubber material, the stress can be factored into a function of frequency and a function of strain(stretch). The finite element methodis applied to analyze non-linear large deformation of rubber material and its results are compared with those of a simplified theory equation. The predicted dynamic material properties based on non-linear static finite element analyses have a good agreement of experimental results and those based on simplified theory equation.