• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.726-733
• /
• 2000

In this article, we introduce a practical case study of the structural design improvement for a vertical machining center. During test operations, it have experienced excessive deflections and vibrations due to the fluctuating forces generated by the ball-screw thrust motor. At first we did investigate where and how much deflections and vibrations had been brought about on it. Next we made some possible structural design alternatives. It is a matter of course to compare finite element static and dynamic analysis results of both the original design and alternatives. Fortunately we have been able to find out a good one among those alternatives.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.58-60
• /
• 1999

In the industrial field the necessity of the linear motion is increasing. We selected a moving magnet coreless type LDM, which have the advantages, such as long stoke, brushless, no cogging force. Actually, the design is accomplished using FEM analysis for the basic configuration of a magnetic circuit, and characteristic equations for coil design. In the course of design, we have estimated airgap flux density and thrust. We fabricated coreless type LDM and experimented static test. We compared measurement values with FEM analysis values.

• 전기학회논문지P
• /
• 제52권4호
• /
• pp.172-178
• /
• 2003

This paper examines the application of high voltage static var compensator(SVC) with cascade multilevel inverter which employs H-bridge inverter(HBI). This method has the primary advantage that the number of voltage levels can be increased for a given number of semiconductor devices when compared to the conventional control methods. The SVC system is modeled using the d-q transform which calculates the instantaneous reactive power. This model is used to design a controller and analyze the SVC system. From the mathematical model of the system, the design procedures of the circuit parameters L and C are presented in this thesis. To meet the specific total harmonic distortion(THD) and ripple factor of the capacitor voltage, the circuit parameters L and C are designed. Simulated and experimental results are also presented and discussed to validate the proposed schemes.

• 한국공작기계학회논문집
• /
• 제16권6호
• /
• pp.103-109
• /
• 2007

With the increase of track density, high rotational speed and the compatibility for various media in optical disk drives, the effective design to vibration reduction is very important for robust operation. Especially when a slim optical disk drive for a notebook PC is excited by a mass-unbalanced disk, internal vibration and its transmission to external case bring about severer problem than that of conventional one. In this paper a design process of a rubber mount in a slim optical disk drive for vibration reduction is presented. The characteristics of rubbery materials - hyper-elastic and visco-elastic - are measured with standard specimens. The static stiffness of a rubber mount was calculated by FEM and the dynamic stiffness is predicted with the static stiffness and the impedance test data of the standard specimen. The transmissibility tests are performed for the purpose of verification of the design process.

• Structural Engineering and Mechanics
• /
• 제49권5호
• /
• pp.631-644
• /
• 2014

Seismic assessment and retrofitting of existing structure is a complicated work that typically requires more sophisticated analyses than performing a new design. Before the implementation of a Code for seismic design of buildings (GBJ 11-89), not enough attention has been paid on seismic performance of structures and a great part of the existing reinforced concrete structures built in China have been poorly designed according to the new version of the same code (GB 50011-2010). This paper presents a case study of seismic assessment of a non-seismically designed reinforced concrete building in China. The structural responses are evaluated using the nonlinear static procedure (the so-called pushover analysis), which requires its introduction within a process that allows the estimation of the demand, against which the capacity is then compared with. The capacity of all structural members can be determined following the design code. Based on the structural performance, suitable retrofitting strategies are selected and implemented to the existing system. The retrofitted structure is analyzed again to check the effectiveness of the rehabilitation. Different types of retrofitting strategy are discussed and classified according to their complexity and benefits. Finally, a proper intervention methodology is utilized to upgrade this typical low-rise non-ductile building.

• 복식문화연구
• /
• 제17권3호
• /
• pp.424-430
• /
• 2009

Taegwondo uniforms need powerful durability in fabrics against friction and shock because of higher exercising power. Therefore, in this study we developed more comfortable Taegwondo uniform for functional fabrics(deodorization rate, antibacterial activity and static charge). Chitosan is a deacetylated product of chitin, has widely been used in the biomedical sector, food industry, and textile industry. For the purpose of this study, we used the chitosan, which was congenial to the human body. Then, we compared the differences between the chitosan treated fabrics and non treated fabrics of Taegwondo uniform(100% polyester, 65% polyester/35% cotton). Chitosan was dissolved in 1% acetic acid. Also, the fabrics were washed using distilled water. Afterward, its treatment with chitosan was completed by padding the sample to its wet pick-up at $80{\pm}5%$ and by heating $150^{\circ}$ for 3 minutes. The chitosan treated Taegwondo uniform was improved on deodorization rate than non treated uniform. And the chitosan treated Taegwondo uniform was improved remarkably the antibacterial activity in all samples. In the further researches, the static charge was reduced in chitosan treatment uniform.

• Wind and Structures
• /
• 제5권6호
• /
• pp.543-562
• /
• 2002

The main purpose of this study is to discuss the design wind loads for the structural frames of single-layer latticed domes with long spans. First, wind pressures are measured simultaneously at many points on dome models in a wind tunnel. Then, the dynamic response of several models is analyzed in the time domain, using the pressure data obtained from the wind tunnel experiment. The nodal displacements and the resultant member stresses are computed at each time step. The results indicate that the dome's dynamic response is generally dominated by such vibration modes that contribute to the static response significantly. Furthermore, the dynamic response is found to be almost quasi-static. Then, a series of quasi-static analyses, in which the inertia and damping terms are neglected, is made for a wide range of the dome's geometry. Based on the results, a discussion is made of the design wind load. It is found that a gust effect factor approach can be used for the load estimation. Finally, an empirical formula for the gust effect factor and a simple model of the pressure coefficient distribution are provided.

• 대한기계학회논문집A
• /
• 제29권3호
• /
• pp.369-386
• /
• 2005

Various aspects of structural optimization techniques under transient loads are extensively reviewed. The main themes of the paper are treatment of time dependent constraints, calculation of design sensitivity, and approximation. Each subject is reviewed with the corresponding papers that have been published since 1970s. The treatment of time dependent constraints in both the direct method and the transformation method is discussed. Two ways of calculating design sensitivity of a structure under transient loads are discussed - direct differentiation method and adjoint variable method. The approximation concept mainly focuses on re- sponse surface method in crashworthiness and local approximation with the intermediate variable Especially, as an approximated optimization technique, Equivalent Static Load method which takes advantage of the well-established static response optimization technique is introduced. And as an application area of dynamic response optimization technique, the structural optimization in flexible multibody dynamic systems is re- viewed in the viewpoint of the above three themes

• 한국기계가공학회지
• /
• 제8권1호
• /
• pp.10-17
• /
• 2009

Spindle design is very important for the improvement of the competitive power in production cost of high quality machine tools. The important factor in spindle design is not only to improve the natural frequency of spindle but also to reduce displacement of spindle end. In this paper, parameters those influence on static and dynamic stiffness of high-speed spindle have selected form preceding studies. And those selected parameters are applied to Taguchi Method. To perform FEM analysis, bearing conditions are selected with optimized condition. To know how to improve static and dynamic stiffness of machine tool spindle, natural frequency and displacement of spindle end are obtained by FEM analysis. The Taguchi Method was used to draw optimized condition of bearing position and it's stiffness. From these results, amplitude of vibration is enough good less than $3{\mu}m$ pk-pk of the spindle of 40,000rpm manufactured in this work by the optimal design.

• 동력기계공학회지
• /
• 제5권4호
• /
• pp.82-89
• /
• 2001

To design a structural or a mechanical system with the best performance, the main procedure of a typical design usually consists of repeated modifications of design parameters and the investigation of the system response for each set of these parameters. But this procedure requires much time, effort and experience. Sensitivity analysis can provide systematic information for improving performance of a system. The author has studied on the development of the structural analysis algorithm and suggested recently the transfer stiffness coefficient method(TSCM). This method is very suitable algorithm to a personal computer because the concept of the TSCM is based on the transfer of the nodal stiffness coefficients which are related to force and displacement vectors at each node. In this paper, a new sensitivity analysis algorithm using the concept of the TSCM is formulated for the computation of state variable sensitivity in static problems. The trust of the proposed algorithm is confirmed through the comparison with the computation results using existent sensitivity analysis algorithm and reanalysis for computation models.