• The Journal of Advanced Prosthodontics
• /
• v.3 no.4
• /
• pp.196-203
• /
• 2011

PURPOSE. This study evaluated marginal fit of glass infiltrated alumina cores fabricated using two techniques and their marginal stability after firing cycles of veneering porcelain. MATERIALS AND METHODS. Fifteen standardized all-ceramic crowns were fabricated on a metal die using each technique: slip cast technique of VITA In-Ceram sprint Alumina (Group A as control) and plastic foil matrix technique of Turkom-Cera fused alumina core system (Group B). Copings were compared between groups and within groups at coping stage and after firing each layer of veneering porcelain. A device was used to standardize seating of copings on the metal die and positioning of the specimens under the microscope after each stage of fabrication. The specimens were not cemented and marginal gap was measured using an image analyzing software (Imagepro Express) on the photographs captured under an optical microscope. Two tailed unpaired 't test' was used to compare marginal gaps in two groups and one way ANOVA was used to analyze marginal distortion within each group at 95% confidence interval. RESULTS. The marginal gap was smaller at the coping stage in group B ($60+30{\mu}M$) than group A ($81+21{\mu}M$) with statistical significance. After firing of veneering porcelain the difference was insignificant. At the final stage, both groups exhibited lower mean marginal gaps than at the initial coping stage with the difference of $11.75{\mu}M$ for group A and $11.94{\mu}M$ for group B, but it was statistically insignificant due to high value of standard deviation. CONCLUSION. Within the limitations of this study, it was concluded that both techniques produced copings with comparable and acceptable marginal fit and marginal stability on firing veneering porcelain.

• Journal of Technologic Dentistry
• /
• v.30 no.1
• /
• pp.17-23
• /
• 2008

Gypsum products are used for the preparation of stone casts of oral and maxillofacial structures and as important adjuncts to dental laboratory operations involved in the production of dental prosthesis. Accuracy and dimensional stability over time are properties of concern in fixed prothodontics. Gypsum products used in denstry are a form calcium sulfate hemihydrate and are classified as 1 of 5 types according to International Standard Organization(ISO) 6873. All die materials exhibit some dimensional change during setting, but expansion and contraction during setting and dimensional changes in response to varations in temperature and the water-powder ratio must be minimal. Although numerous investigators have studied the properties of die materials, several products have been introduced recently with manufacturer claims of superior dimensional stalility. The aim of this study was to determine the surface properties using various separating materials of dental gypsum products The results were as follows 1. In the comparison of first and second plaster distances before separation in different separating agent, there was no significant difference except using Trio separating agent. The interface using Trio separating agent forms like to pores. 2. In the comparison of first and second plaster distances after separation in different separating agent, there was significant difference. The interface of plasters using WD-40, Trio and Vaseline was showed some gaps. Each they were measured at average 7.97 $\pm$ 2.07 ${\mu}m$, 63.09 $\pm$ 23.25 ${\mu}m$, 27.59 $\pm$ 4.19 ${\mu}m$. 3. In the comparison of the surface, the surface of control sample(using none seperating agent) showed irregular properties and the surface using Trio and Vaseline become wrinkled. Specially the surface using Vaseline was showed shiny properties. But the surface using MAGIC SEP, Plaster seperating agent, WD-40 showed regular properties.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.4
• /
• pp.328-334
• /
• 2018

PURPOSE. To evaluate the reproducibility of scan-based abutments using a blue light model scanner. MATERIALS AND METHODS. A wax cast abutment die was fabricated, and a silicone impression was prepared using a silicone material. Nine study dies were constructed using the prepared duplicable silicone, and the first was used as a reference. These dies were classified into three groups and scanned using a blue light model scanner. The first three-dimensional (3D) data set was obtained by scanning eight dies separately in the first group. The second 3D data set was acquired when four dies were placed together in the scanner and scanned twice in the second group. Finally, the third 3D data set was obtained when eight dies were placed together in the scanner and scanned once. These data were then used to define the data value using third-dimension software. All the data were then analyzed using the non-parametric Kruskal-Wallis H test (${\alpha}=.05$) and the post-hoc Mann-Whitney U-test with Bonferroni's correction (${\alpha}=.017$). RESULTS. The means and standard deviations of the eight dies together were larger than those of the four dies together and of the individual die. Moreover, significant differences were observed among the three groups (P<.05). CONCLUSION. With larger numbers of abutments scanned together, the scan becomes more inaccurate and loses reproducibility. Therefore, scans of smaller numbers of abutments are recommended to ensure better results.

• The Journal of Advanced Prosthodontics
• /
• v.13 no.2
• /
• pp.89-99
• /
• 2021

PURPOSE. This study aimed to compare the accuracy (trueness and precision) of interim crowns fabricated using DLP (digital light processing) according to post-curing time. MATERIALS AND METHODS. A virtual stone study die of the upper right first molar was created using a dental laboratory scanner. After designing interim crowns on the virtual study die and saving them as Standard Triangulated Language files, 30 interim crowns were fabricated using a DLP-type 3D printer. Additively manufactured interim crowns were post-cured using three different time conditions-10-minute post-curing interim crown (10-MPCI), 20-minute post-curing interim crown (20-MPCI), and 30-minute post-curing interim crown (30-MPCI) (n = 10 per group). The scan data of the external and intaglio surfaces were overlapped with reference crown data, and trueness was measured using the best-fit alignment method. In the external and intaglio surface groups (n = 45 per group), precision was measured using a combination formula exclusive to scan data (10C2). Significant differences in accuracy (trueness and precision) data were analyzed using the Kruskal-Wallis H test, and post hoc analysis was performed using the Mann-Whitney U test with Bonferroni correction (α=.05). RESULTS. In the 10-MPCI, 20-MPCI, and 30-MPCI groups, there was a statistically significant difference in the accuracy of the external and intaglio surfaces (P<.05). On the external and intaglio surfaces, the root mean square (RMS) values of trueness and precision were the lowest in the 10-MPCI group. CONCLUSION. Interim crowns with 10-minute post-curing showed high accuracy.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.1
• /
• pp.123-136
• /
• 2018

The objective of this study is to propose a new methodology to fabricate a reliable engineering-scale buffer block, which shows homogeneous and uniform distribution in buffer block density, for in-situ experiments. In this study, for the first time in Korea, floating die press and CIP (Cold Isostatic Press) are applied for the manufacture of an engineering-scale bentonite buffer. The optimized condition and field applicability are also evaluated with respect to the method of manufacturing the buffer blocks. It is found that the standard deviation of the densities obtained decreases noticeably and that the average dry density increases slightly. In addition, buffer size is reduced by about 5% at the same time. Through the test production, it is indicated that the stress release phenomenon decreases after the application of the CIP method, which leads to a reduction in crack generation on the surface of the buffer blocks over time. Therefore, it is confirmed that the production of homogeneous buffer blocks on industrial scale is possible using the method suggested in this study, and that the produced blocks also meet the design conditions for dry density of buffer blocks in the AKRS (Advanced Korea Reference Disposal System of HLW).

• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.113-123
• /
• 2022

The required density relationship according to the press pressure of the floating die method and the homogeneity of the density distribution in the buffer block was evaluated to analyze the manufacturing characteristics of engineering scale bentonite-sand buffer blocks. In addition, the thermal conductivity was measured and compared with that of the pure bentonite buffer block to evaluate the level of thermal conductivity performance improvement of the bentonite-sand buffer material. As a result, it was confirmed that the standard deviation of dry density decreased to 0.011 and showed a homogeneous density distribution under the condition of press pressure greater than 400 kg/cm². Furthermore, as a result of the thermal conductivity test, the thermal conductivity of the buffer with optimum moisture content conditions was 1.345 and 1.261 W/(m·K) under the press pressure of 400 and 600 kg/cm², respectively. It increased by 16.1% and 11.0% compared to the pure bentonite buffer material. Based on the results of this study, it is judged that it can be used as fundamental data for manufacturing a homogeneous bentonite-sand buffer block on an engineering scale.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.1-8
• /
• 2017

In this study, we applied microcellular foaming injection molding process to improve the performance of system air-conditioner drain fan which had been produced by injection molding process and studied the optimization of process conditions through 6-sigma process and response surface method (RSM) to reduce weight and deformation of products. Additive type, melt temperature, mold temperature, and injection screw shape were selected as the factor affecting the weight and deformation of the products by carrying out analysis of trivial many through ANOVA and design of experiment (DOE) method. Among the effect factor, we set the addictive type to Long G/F and screw shape to foaming screw which had the highest level of weight reduction and deformation reduction. The amount of foaming agent gas was set at 60 ml, which was the limit beyond which the weight of product did not decrease any more. For melt temperature and mold temperature, we studied the conditions where both weight and deformation were minimized using the RSM. As a result, we set the melt temperature to $250^{\circ}C$, fixed mold temperature to $20^{\circ}C$, and moving mold temperature to $40^{\circ}C$. The improvement effect was analyzed by appling the selected optimal conditions to the production process using the microcellular foaming injection molding. The results showed that the mean weight of product was measured to be 1,420g which was 19% lower than that measured in the current process. The standard deviations of the weights were found to be similar to those in the current process and it showed a low dispersion. The mean deformation was measured to be 0.9237mm, which represented a 57% reduction compared to the mean deformation in the current process, and the standard deviation decreased from 0.3298mm to 0.1398mm. Moreover, we analyzed the process capability for deformation, and the results showed that the short-term process capability increased from 2.73 to 6.60 which was even higher than targeted level of 6.0.

• Korean Journal of Ecology and Environment
• /
• v.41 no.4
• /
• pp.431-440
• /
• 2008

Turbid water or suspended sediment is associated with negative effects on aquatic organisms; fish, aquatic invertebrate, and periphyton. Effects of turbid water on fish differ depending on their developmental stage and a level of turbidity. Low turbid water may cause feeding and predation rates, reaction distance, and avoidance in fish, and it could make fish to die under high turbidity and long period. Therefore, it is very important to find out how turbid water or suspended sediment can affect fish in domestic watersheds. The objectives of this study were 1) to introduce international case studies and their standards to deal with suspended sediment, 2) to determine acute toxicity in 4 major freshwater fishes, and 3) to determine in relation to adverse effect of macroinvertebrates and fish. Impacts of turbid water on fish can be categorized into direct and indirect effects, and some factors such as duration and frequency of exposure, toxicity, temperature, life stage of fish, size of particle, time of occurrence, availability of and access to refugia, etc, play important role to decide magnitude of effect. A review of turbidity standard in USA, Canada, and Europe indicated that each standard varied with natural condition, and Alaska allowed liberal increase of turbidity over natural conditions in streams. Even though acute toxicity with four different species did not show any fatal effect, it should be considered to conduct a chronic test (long-term) for more detailed assessment. Compared to the control, dominance index of macroinvertebrates was greater in the turbid site, whereas biotic index, species diversity index, species richness index, and ecological score were smaller in the turbid site. According to histopathological analysis with gills of macroinvertebrate and fishes, morphological and physiological modification of gills due to suspended sediments can cause disturbance of respiration, excretion and secretion. In conclusion, in order to maintain good and healthy aquatic ecosystem, it is the best to minimize or prevent impact by occurrence of turbid water in stream and reservoir. We must make every effort to maintain and manage healthy aquatic ecosystem with additional investigation using various assessment tools and periodic biomonitoring of fish.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.3
• /
• pp.182-187
• /
• 2017

PURPOSE. Vinyl polyether silicone (VPES) has a different composition from other elastomeric impression materials as it combines vinyl polysiloxane (VPS) and polyether (PE). Therefore, it is important to study its properties and behavior under different test conditions. This study investigated the dimensional stability of 5 VPES consistencies when stored for up to 2 weeks, with and without using a standard disinfection procedure. MATERIALS AND METHODS. 40 discs of each VPES consistency (total 200) were made using a stainless steel die and ring as described by ANSI /ADA specification No. 19. 20 discs of each material were immersed in a 2.5% buffered glutaraldehyde solution for 30 minutes. Dimensional stability measurements were calculated immediately after fabrication and repeated on the same discs after 7 and 14 days of storage. The data was analyzed using two-way ANOVA with a significance level set at ${\alpha}=0.05$. RESULTS. The discs mean contraction was below 0.5% at all test times ranging from $0.200{\pm}0.014$ to $0.325{\pm}0.007$. Repeated measures ANOVA showed a statistically significant difference after 2-week storage between the disinfected and non-disinfected groups (P < .001). Although there was no statistically significant difference between the materials at the time of fabrication, the contraction of the materials increased with storage for 1 and 2 weeks. CONCLUSION. The dimensional changes of VPES impression discs after disinfection and prolonged storage complied with ANSI/ADA standard. The tested VPES impression materials were dimensionally stable for clinical use after disinfection for 30 minutes in glutaraldehyde and storage for up to 2 weeks.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.2
• /
• pp.63-71
• /
• 2002

This paper suggests a 8-bit RISC microcontroller, which has a 4-stage pipeline architecture. Many low-power design techniques that have been proposed by previous works are adopted into it. The proposed microcontroller consumes only 600㎼ per MIPS for 0.6 ${\mu}{\textrm}{m}$ CMOS process and even lower power of 70㎼ per MIPS for 0.25${\mu}{\textrm}{m}$ process. The RTL level design of this microcontroller is carried out using VHDL. The functional verification is thoroughly done at the gate level using 0.6${\mu}{\textrm}{m}$/0.25${\mu}{\textrm}{m}$ CMOS IDEC standard cell library. This microcontroller contains 7000 NAND gates on a 0.36$\textrm{mm}^2$ die using 0.25${\mu}{\textrm}{m}$ process. Finally the comparison of power consumption with other conventional microcontrollers is provided.