• 제목/요약/키워드: standard GA

검색결과 250건 처리시간 0.02초

GD-MS 분석 장비를 활용한 극미량 무기물 질량 분석을 위한 표준RSF 구축 및 응용 (Establishment and application of standard-RSF for trace inorganic matter mass analysis using GD-MS)

  • 장민경;양재열;이종현;윤재식
    • 분석과학
    • /
    • 제31권6호
    • /
    • pp.240-246
    • /
    • 2018
  • 본 연구에서는 GD-MS를 활용하여 원소 별 함량이 다른 세 종류의 알루미늄 매질의 표준 시료를 분석하였다. 13 종의 원소(Mg, Si, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Sn, Pb)에 대해 검량 곡선을 작성하고 그 기울기를 RSF(Relative sensitivity reference)로 확립하였다. 검량 곡선은 X축을 IBR(Ion beam ratio)로, Y축을 표준 시료의 인증 값으로 작성하였다. 검량 곡선의 정밀도와 직선성을 평가하기 위해 RSD(Relative standard deviation)와 결정 계수를 계산하였다. 그 결과 모든 원소의 RSD는 10 %이내로 높은 정밀도를 나타냈다. 바나듐, 니켈 그리고 갈륨 원소를 제외한 대부분의 원소들은 결정 계수가 0.99 이상으로 1에 가까운 값을 얻어 직선성이 우수했다. 바나듐, 니켈 그리고 갈륨 원소는 결정 계수가 0.90~0.95 범위로 비교적 낮은 직선성을 나타냈으며, 이는 좁은 농도 범위로 인한 오차로 판단된다. 바나듐, 니켈 그리고 갈륨 원소는 결정 계수는 낮지만 각각의 표준 시료 RSF와 기울기로 확립한 표준RSF(Standard-RSF)가 비슷하여 정량 분석을 위한 RSF로 활용 가능할 것으로 판단된다. 다른 매질의 시료에 표준RSF(Al matrix)를 적용 가능 여부와 실제 표준 값에 대한 오차를 확인하기 위해서 철 매질(Fe matrix)의 표준 시료를 분석하여 검증하였다. 구리 원소를 제외한 6 종(Al, Si, V, Cr, Mn, Ni) 원소의 오차율은 약 30 %로 나타났으며, 구리 원소는 측정을 방해하는 불순물 화합물의 영향으로 오차율이 크게 나타난 것으로 판단된다. 일반적으로 동위원소$^{63}Cu$$^{54}Fe^{2+}-^{36}Ar$ 간섭을 받고 $^{65}Cu$$^{56}Fe-Al^{3+}$간섭을 받는다. 이를 분해하기 위해서는 8000 이상의 분해능이 필요하다. 하지만, 높은 분해능은 이온의 투과도를 낮추기 때문에 미량원소 분석에 어려움이 있다. 구리 원소를 제외한 알루미늄 외 5종의 원소에 대해서는 비교적 적은 오차로 정량 분석이 가능한 것으로 확인되었다.

국화 수확 후 관리기술의 최근 연구 동향 (Current Research Trend of Postharvest Technology for Chrysanthemum)

  • 김수정;이승구;김기선
    • 한국자원식물학회지
    • /
    • 제25권1호
    • /
    • pp.156-168
    • /
    • 2012
  • 절화국화는 수명이 1-2주이며, 최대 3-4주까지 유지되고 수확 후 호흡증대와 노화가 급격하게 진행되지 않는 non-climateric 식물로서 에틸렌에 대한 감수성이 낮은 작목이다. 절화는 주로 잎이 위조, 황화되고 수분의 이동이 방해되어 엽록소가 퇴화되고 잎의 노화가 촉진되어 개화되지 못하므로 품질이 떨어진다. 절화의 수명은 품종, 수확전 재배조건, 수확 후 온도, 습도, 광, 수질 등 외부요인 및 기질의 공급, 체관 및 물관의 흡수력 유지, 에틸렌과 같은 호르몬, 효소활성 변화 등의 내부요인에 의해 좌우된다. 국화 품질지표는 꽃과 줄기가 구부러짐이 없고 절간간격 및 잎 크기의 상하가 일정하며 균형이 잘 잡힌 것이어야 하며, 화형, 화색이 품종 본래의 특성을 갖추고 모두 양호하여야 하며 병해충 피해가 확인되지 않으며, 절화 수확시기가 적기인 것이여야 한다. 스탠다드 국화는 꽃봉오리가 5-6cm일 때 수확하고, 스프레이 국화는 40% 개화상태인 2-4개의 봉오리가 균일하게 개화하면 수확한다. 이 때 토양 기부에서부터 10 cm 위로 잘라 목질화된 줄기를 제거하며 줄기 아래쪽의 잎을 1/3정도 제거하여 수분흡수가 잘 이루어지도록 한다. 수확 후 절화를 등급별로 나누게 되는데 절화의 길이와 무게, 꽃의 개화상태를 기준으로 한다. 스탠다드 국화는 병해충이 없고, 줄기가 구부러짐이 없고, 잎 크기가 균형이 잘 잡히고 절화장이 80 cm, 절화줄기 1개의 무게가 70 g이면 가장 우수한 1등급이며, 스프레이 국화는 절화장과 절화무게가 각각 70 cm, 60 g이고, 개화는 2-4륜이 개화하고, 병해충이 없는 깨끗한 상태인 경우가 1등급이다. 절화수명을 연장하기 위하여 물올림과 동시에 전처리제를 사용하는데, STS, GA, BA, 1-MCP, Chrysal, 살균제, sucrose 등이 이용되고 있다. 절화의 호흡감소, 부패감소, 변색지연, 증산억제를 위해 예냉을 $5{\sim}7^{\circ}C$에서 4시간 이상 하는 것이 좋다. 절화국화는 PE필름으로 포장해서 상자에 넣으면 $2^{\circ}C$에서 2주간 저장이 가능하고, 습식에서는 3주간 저장이 가능하다. 포장이 끝난 국화는 저온차량를 이용하여 수송 상차 및 하역비 절감을 위해 2상자씩 묶어 출하한다. 소비자가 신선한 꽃을 오랫동안 감상하는 위해 HQS, 탄산수, sucrose 등을 이용하여 수확 후 후처리를 한다. 절화 국화의 소비 및 이용을 다변화하기 위해서는 유통 품목과 품종의 다양화, 유통체계의 정비, 산지 생산자-소매자-소비자의 정보교류 등이 필요할 것이다.

하폐수의 재사용 및 방류를 위한 폭기조 내 표준산소전달 효율 모니터링 시스템에 관한 연구 (Study on the Standard Oxygen Transfer Efficiency Monitoring System in the Aeration Tank for Reuse and Discharge of Wastewater)

  • 김홍석;김용범;고경한;김상우;심환보
    • 자원리싸이클링
    • /
    • 제28권6호
    • /
    • pp.73-78
    • /
    • 2019
  • 본 연구에서는 활성 슬러지 하수처리장에서 배출되는 off-gas에 대한 포집 및 측정 모니터링을 통해 폭기조의 산소전달효율을 측정하고 청수와 비교하여 시스템의 신뢰성을 검증하는 연구를 수행하였다. 먼저, 청수를 기반으로 용존산소, 산소전달계수 및 표준산소전달효율을 측정하였으며 각각 8.60 mg/L, 9.49/hr, 23.96%의 값이 얻어졌다. 한편, 하수처리장 현장에서 진행한 off-gas 시험 결과 표준산소전달효율이 22.81%로 계산되어 청수와의 차이가 거의 없는 것으로 나타났다. 이는 현장에 설치된 산기관의 성능 및 폭기조의 상황을 모니터링 시스템을 이용해 실시간으로 확인함으로써 신뢰성있는 데이터를 확보할 수 있음을 의미한다.

공동주택 시공표준화를 위한 조립기준면 및 표준마무리재에 관한 연구 (A Study on the Standard Joint Material and Reference Plane for the Standard of Construction in the Apartment)

  • 임석호;박근수;이가경
    • 한국주거학회:학술대회논문집
    • /
    • 한국주거학회 2009년 춘계학술발표대회 논문집
    • /
    • pp.230-235
    • /
    • 2009
  • In our country, the application of the design method of face to face dimension in wall-slab apartment has passed 10 years. So MC design method has fixed in the design step to some degree. In Design and Work Execution of House the exclusive area of the apartment was calculated by face to face dimension. And the term of face to face dimension was known broadly to clients, construction company, etc. But design method of face to face dimension is not to simply extend the room size so far as wall depth in design process but to ensure the actual space should be considered with efficient use and assembly of building components. That is to say, Design method of face to face dimension is not to be defined by design step but to be related with construction and maintenance. However in construction process the point of face to face design method was not understood even now. So the purpose of this study was to extract the effect and question of face to face design method in construction process by survey of actual condition of structure and construction quality, and compare this result with existing construction method. The following project of this study is to survey of actual condition of interior components such as gypsum board, windows & doors etc. Therefore this study is to induce architectural long-life through architectural standardization construction and component's exchange, and, by the subject of the study on Apartment to have design guideline and basis for joining part between Gypsumboard and windows.

  • PDF

공동주택 시공표준화를 위한 조립기준면 및 표준마무리재에 관한 연구 - 석고보드 마감재와 창호재의 접합부위를 중심으로 - (A Study on the Standard Joint Material and Reference Plane for the Standard of Construction in the Apartment - Joining Part between Gypsumboard and Windows -)

  • 임석호;박근수;이가경
    • 한국주거학회논문집
    • /
    • 제20권4호
    • /
    • pp.31-38
    • /
    • 2009
  • In our country, the application of the design method of face to face dimension in wall-slab apartment has passed 10 years. So MC(Modular Coordination) design method has fixed in the design step to some degree. In Design and Work Execution of House the exclusive area of the apartment was calculated by face to face dimension. And the term of face to face dimension was known broadly to clients, construction company, etc. But design method of face to face dimension is not to simply extend the room size so far as wall depth in design process but to ensure the actual space should be considered with efficient use and assembly of building components. That is to say, Design method of face to face dimension is not to be defined by design step but to be related with construction and maintenance. However in construction process the point of face to face design method was not understood even now. So the purpose of this study was to extract the effect and question of face to face design method in construction process by survey of actual condition of structure and construction quality, and compare this result with existing construction method. The following project of this study is to survey of actual condition of interior components such as gypsum board, windows & doors etc. Therefore this study is to induce architectural long-life through architectural standardization construction and component's exchange, and, by the subject of the study on Apartment to have design guideline and basis for joining part between Gypsumboard and windows.

공동주택 안목치수 설계기준에 의한 붙박이장의 표준화방안 연구 (A Study on the Standardization of the Built-in Wardrobe by Housing Inside Dimension)

  • 이가경;임석호
    • 한국주거학회논문집
    • /
    • 제21권6호
    • /
    • pp.53-60
    • /
    • 2010
  • Built-in wardrobe is constructing after ordering and making, because built-in wardrobe's size is fixed as housing measurement. It is hard to speak built-in wardrobe components of construction in these ways, and application of an MC (Modular Coordination) design system is meaningless too. And above all, measurement before construction isn't to expect standardization, and to increase custom-made furniture. So I suggest the standardization of built-in wardrobe utilizing standard last finish and reference plane in order to prevent an evil influence of built-in wardrobe's construction. And we utilized a reference plane, and we present construction document and design plan in order to solve these problems. The first stage, we investigate manufacture of a preferential domestic system kitchen and construction state, and we derive from a problem in viewpoints of standardization for this. And we analyze an effect got by application of the assembly basis aspect that we presented, and we can raise efficiency of standardization of housing and construction industry, and we light ultimately up. I will apply a standardization plan as above, and define that this assures a standardization of components and an economic effect.

H-UV 무습수 오프셋 인쇄에서 CMS 적용에 관한 연구 (Study on CMS Application in Hybrid UV Waterless Off-Set Printing)

  • 구철회;조가람
    • 펄프종이기술
    • /
    • 제45권5호
    • /
    • pp.1-13
    • /
    • 2013
  • This study found fit optimum C, M, Y, K solid density and $CIEL^*a^*b^*$ value to paper & ink as well as check about printing machine state for color management in H-UV waterless off-set printing first. These values applied to GRACoL G7 calibration method. This method is one of color standard management method of printing. GRACoL G7 calibration method is possible stable tone reappearance by controlling gray balance by NPDC(Natural Printing Density Curve). Also, this study used values to make device profile as result that is gotten by application of GRACoL G7 calibration method. This profile was applied to CMS(Color Management System) of H-UV waterless off-set printing, and the result was possible by color management that correspond in printing quality standard of ISO 12647-2 and GRACol 2006 specifications.

ISO 30300 원리와 ISO 30301 요구사항 분석 (An Analysis of ISO 30300 Principles and ISO 30301 Requirements)

  • 류가현;김희섭
    • 한국기록관리학회지
    • /
    • 제12권1호
    • /
    • pp.95-115
    • /
    • 2012
  • 본 연구의 목적은 ISO 30300 기본사항에서 제시하고 있는 MSR 원리와 ISO 30301 요구사항의 세부 내용을 분석함으로써 이에 대한 전반적인 이해의 폭을 넓히고 궁극적으로는 향후 MSR 구축하고자 하는 조직에게 개념적인 틀을 제공하고자 함이다. 본 연구의 목적을 달성하기 위하여 2011년 발간된 'ISO/FDIS 30300 MSR-기본사항 및 용어'와 'ISO/FDIS 30301 MSR-요구사항'간의 관련성을 매트릭스 다이어그램을 사용하여 분석하였다. 분석결과 MRS 요구사항은 원리를 바탕으로 수립되었기 때문에 모든 원리가 개별 요구사항 조항과 직 간접적으로 관련성을 보이고 있다는 것을 확인하였고, 그 중 특히 '프로세스 접근법' 원리가 가장 강조된 것을 알 수 있었다.

유방암에 대한 한양방 병용 치료 증례 보고 1례 (A Case Study of a Patient with Breast Cancer Treated with a Combination of Traditional Korean Medicine and Chemotherapy)

  • 한가진;이아람;정준석;성신;김성수
    • 대한한방내과학회지
    • /
    • 제38권5호
    • /
    • pp.820-827
    • /
    • 2017
  • The prevalence of breast cancer is very high in Korea. Although the patients receive standard treatments, such as surgery, chemotherapy, or radiotherapy, they frequently experience recurrence or metastasis of their tumors. In addition, many patients with breast cancer also suffer from side effect symptoms induced by these standard treatments. Therefore, increasing numbers of patients now want to undergo treatment with traditional Korean medicine (TKM) in addition to conventional treatment. We present a case of 46-year-old female with recurred breast cancer. She first received two kinds of chemotherapy and then underwent surgery. She then also received 4 cycles of adjuvant chemotherapy. At a follow-up examination, she was informed of recurrent lesions on the right anterior chest wall. She started to receive TKM treatments together with a new chemotherapy. After about one month, the size of the recurred tumor in right chest wall had decreased. Her symptoms, such as shoulder pain, chest pain, and nausea induced by conventional therapy, were also improved. We suggest that a combination of TKM and chemotherapy is a promising treatment for breast cancer.

백금저항온도센서를 이용한 국가교정기관의 교정능력 평가 및 실험방법 (Experimental method and evaluation of the calibration capability for the national calibration centers using the platinum resistance temperature sensors)

  • 감기술;유성호;김성민;이인식
    • 센서학회지
    • /
    • 제14권4호
    • /
    • pp.231-236
    • /
    • 2005
  • Calibration capability was evaluated using the reference-grade platinum resistance thermometer (PRT) in the temperature range of $-50^{\circ}C$ to $250^{\circ}C$ for the national calibration centers. The reference-grade PRT was calibrated at the several fixed points, which was composed by the freezing points of Sn, In, the melting point of Ga and the triple point of water and Hg, before and after the round-robin test (RRT) experiments. The temperature scale of reference-grade PRT was compared to the local standard PRT's using the system of the national calibration centers. $E_{n}$ values was calculated by the temperature difference between the reference-grade PRT and the local standard PRT, and the best measurement capability. Finally, the capability of the national calibration centers was evaluated by the $E_{n}$ values.