• Journal of the Korean Society of Safety
• /
• v.28 no.5
• /
• pp.10-14
• /
• 2013

This paper is aimed to investigate the actual conditions of standalone PV(Photovoltaics) streetlight in public place and analyze cause of failure and derive the method of decrease for standalone PV streetlight. The cost of installing standalone PV streetlight in a public for the safety and convenience of life is expensive(300 million won per unit). Management of standalone PV streetlight is important because it is operating system itself, after installation, but concern degree of management is very low and development of technology has not been done. Accordingly, standalone PV streetlight in public place is not operate in night, this phenomenon is lasted for several days to months. Therefore this study, for standalone PV streetlight constantly to keep the normal operation, investigation conducted to check status of standalone PV streetlight(50 units), the voltage of the main parts and analyze the cause of the failure. In addition, the improvement of standalone PV streetlight is suggested by using FTA(fault tree analysis).

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2004-2012
• /
• 2014

Energy storage devices are necessary to obtain stable utilization of renewable energy sources. When black-out occurs, distributed renewable power sources with energy storage devices can operate under standalone mode as uninterruptable power supply. This paper proposes a dynamic response analysis with small-signal modeling for the standalone operation of a photovoltaic power generation system that includes a bidirectional charger/discharger with a battery. Furthermore, it proposes a DC-link voltage controller design of the entire power conditioning system, using the storage current under standalone operation. The purpose of this controller is to guarantee the stable operation of the renewable source and the storage subsystem, with the power conversion of a very efficient bypass-type PCS. This paper presents the operating principle and design guidelines of the proposed scheme, along with performance analysis and simulation. Finally, a hardware prototype of 1-kW power conditioning system with an energy storage device is implemented, for experimental verification of the proposed converter system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.8
• /
• pp.375-380
• /
• 2014

The purpose of this paper is to investigate the cooling and heating performance of a standalone-type thermoelectric system equipped with a thermoelectric module. The system consists of a blower and two thermoelectric modules with a fin, which is soldered onto both sides of the thermoelectric module and a courtesy light. The thermoelectric system experiment is conducted with the intake voltage to find the optimum cooling and heating performance of each. The results showed that the cooling capacity and coefficient of performance (COP) were 22 W and 0.31, and the heating capacity and COP were 147 W and 1.1, respectively. In the vehicle cooling and heating performance test in a climate wind tunnel, the results showed that the standalone thermoelectric system's cooling performance was slightly better than the base system; and the heating performance of the standalone thermoelectric system was $54.1^{\circ}C$ and the COP was 1.3, compared to the base system.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.10
• /
• pp.4098-4116
• /
• 2020

Mobile devices such as smartphones are very attractive targets for augmented reality (AR) services, but their limited resources make it difficult to increase the number of objects to be recognized. When the recognition process is scaled to a large number of objects, it typically requires significant computation time and memory. Therefore, most large-scale mobile AR systems rely on a server to outsource recognition process to a high-performance PC, but this limits the scenarios available in the AR services. As a part of realizing large-scale standalone mobile AR, this paper presents a solution to the problem of accuracy, memory, and speed for large-scale object recognition. To this end, we design our own basic feature and realize spatial locality, selective feature extraction, rough pose estimation, and selective feature matching. Experiments are performed to verify the appropriateness of the proposed method for realizing large-scale standalone mobile AR in terms of efficiency and accuracy.

• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.70-76
• /
• 2019

This paper reports development of a low-power standalone heat detector using a Critical-Temperature Switch. The Critical-Temperature Switch, which is a thermally sensitive and passive component whose resistance decreases significantly at 70 ℃ due to a metal-insulator transition, provides reliable temperature measurements. This digital-like behavior of the Critical-Temperature Switch can detect fires without a microcontroller, meaning that it can minimize the power consumption of the standalone heat detector. The experimental results showed that the standalone heat detector using the Critical-Temperature Switch complied with the Notification of the National Emergency Management Agency. Compared to conventional standalone heat detectors, only 70% of the power was consumed monitoring the fires.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.86-93
• /
• 2018

In this work, control methods and operating modes are proposed to manage standalone microgrid. A standalone microgrid generally consists of two sources, namely, battery energy storage system (BESS) and diesel generator (DG). BESS is the main source that supplies active and reactive power regardless of load conditions, whereas DG functions as an auxiliary power source. BESS operates in a constant voltage constant frequency (CVCF) control, which includes proportional-integral + resonant controller in a parallel structure. In CVCF control, the concept of fundamental positive and negative transformation is utilized to generate a three-phase sinusoidal voltage under imbalanced load condition. Operation modes of a standalone microgrid are divided into three modes, namely, normal, charge, and manual modes. To verify the standalone microgrid along with the proposed control methods, a demonstration site is constructed, which contains 115 kWh lead-acid battery bank, 50 kVA three-phase DC - AC inverter, and 50 kVA DG and controllable loads. In the CVCF control, the total harmonic distortion of output voltage is improved to 1.1% under imbalanced load. This work verifies that the standalone microgrid provides high-quality voltage, and three operation modes are performed from the experimental results.

• The Research Journal of the Costume Culture
• /
• v.32 no.2
• /
• pp.260-286
• /
• 2024

This study investigates consumer experiences and word-of-mouth (WOM) intentions in luxury brand pop-up stores, including standalone and department store setups. Grounded in experience economy theory, this study examines the experiential elements based on the types of pop-up stores and the relationships among consumer experience, pop-up store image, and WOM intentions for each type. Data were collected from 300 visitors to luxury brand pop-up stores between January and July 2023 and analyzed using Smart PLS 4.0. The findings reveal several key insights. First, standalone pop-up stores offer educational and escapist experiences, while pop-ups within department stores have a single identified factor of consumer experience. Second, regardless of the store type, luxury pop-up store experiences significantly influence pop-up image perceptions. Third, luxury pop-up store image drives WOM intentions for both standalone and department store pop-ups. Notably, the unique image significantly impacts solely department store pop-ups and does not influence standalone pop-ups. Moreover, image perceptions in both pop-up store types do not significantly affect brand WOM intentions. Finally, WOM intentions for pop-up stores significantly influence WOM intentions for brands. This study contributes to the theoretical understanding of consumer experiences in luxury pop-up stores, providing practical insights for stakeholders in the luxury brand industry to enhance pop-up store image perceptions and WOM intentions.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.929-938
• /
• 2015

Maximum power point tracking (MPPT) and battery charging control are two important functions for a solar battery charger. The former improves utilization of the available solar energy, while the latter ensures a prolonged battery life. Nevertheless, complete implementation of both functions can be complex and costly, especially for low voltage application such as standalone street lamps. In this paper, the operation of a solar battery charger for standalone street light systems is investigated. Using only one voltage sensor, the solar charger is able to operate in both MPPT and constant voltage (CV) charging mode, hence providing high performance at a low cost. Using a lab prototype and a solar simulator, the operation of the charger system is demonstrated and its performance under varying irradiance is validated.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.5
• /
• pp.493-504
• /
• 2008

Space-Based Augmentation System (SBAS), which is one of the GPS augmentation systems, is a Wide-Area Differential GPS that provides differential GPS corrections and integrity data. In this study, we did performance analysis of kinematic SBAS surveying by conducting Real-Time Kinematic (RTK), DGPS, standalone, and SBAS surveys. Considering static survey results as truth, 2-D Root Mean Square (RMS) error and 3-D RMS error were computed to evaluate the positioning accuracy of each survey method. As a result, the 3-D positioning error of RTK was 13.1cm, DGPS 126.0cm, standalone (L1/L2) 135.7cm, standalone (C/A) 428.9cm, and SBAS 109.2cm. The results showed that the positioning accuracy of SBAS was comparable to that of DGPS.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.77-85
• /
• 2018

Renewable energy has been increasingly used and widely acclaimed as one of the solutions to rampant environmental problems. Among numerous kinds of renewable sources, the penetration rate of the PV system is relatively higher than that of others due to ease of installation. However, one disadvantage of the PV system is its dependence on weather condition. The PV system is especially critical when it is used for standalone systems because it cannot operate when the power generated from a PV module is not enough. Therefore, PV systems are often used with an energy storage system, such as batteries, to store backup energy when the weather condition is insufficient to supply power to the system. Blackout time can be reduced by increasing the size of the energy storage system, but it is a trade-off with system cost. In this work, optimal sizing of a standalone PV system is proposed to supply power to the system without blackout. The sizing of PV modules and batteries is performed by a simulation based on actual irradiation data collected during the past five years. The Life cycle costing of each system is evaluated to determine an optimal set of PV modules and batteries among several different combinations. The standalone PV system designed by the proposed method can supply power to the system with no interruption as long as the weather condition is similar to those of the past five years.