• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.467-474
• /
• 2010

Stainless steel sheets are widely used as the structural material for railroad cars and commercial vehicles. Structures made of stainless steel sheets are commonly fabricated by gas welding, For the fatigue design of gas welded joints such as fillet joints, it is necessary to obtain design information of the stress distribution at the weldment as well as the fatigue strength of the gas-welded joints. Further, the influence of the geometrical parameters of gas-welded joints on stress distribution and fatigue strength must be evaluated. in this study, ${\Delta}P-N_f$ curves were obtained by fatigue tests. and, the ${\Delta}P-N_f$ curves were rearranged on the basis of the ${\Delta}{\sigma}-N_f$ relation for the hot-spot stresses at the gas-welded joints. These results, were used for conducting an accelerated life test(ALT) From the experiment results, an acceleration model was derived and factors were estimated. The objective is to obtain the information required for the analysis of the fatigue lifetime of fillet welded joints and for data analysis by the statistic reliability method to save time and cost and to develop optimum accelerated life prediction plans.

• Steel and Composite Structures
• /
• v.33 no.3
• /
• pp.445-461
• /
• 2019

The ultrasonic guided wave-based technique has become one of the most promising methods in non-destructive evaluation and structural health monitoring, because of its advantages of large area inspection, evaluating inaccessible areas on the structure and high sensitivity to small damage. To further advance the development of damage detection technologies using ultrasonic guided waves for the inspection of welded components in structures, the transmission characteristics of the ultrasonic guided waves propagating through welded joints with various types of defects or damage in steel plates are studied and presented in this paper. A three-dimensional (3D) finite element (FE) model considering the different material properties of the mild steel, high strength steel and austenitic stainless steel plates and their corresponding welded joints as well as the interaction condition of the steel plate and welded joint, is developed. The FE model is validated against analytical solutions and experimental results reported in the literature and is demonstrated to be capable of providing a reliable prediction on the features of ultrasonic guided wave propagating through steel plates with welded joints and interacting with defects. Mode conversion and scattering analysis of guided waves transmitted through the different types of weld defects in steel plates are performed by using the validated FE model. Parametric studies are undertaken to elucidate the effects of several basic parameters for various types of weld defects on the transmission performance of guided waves. The findings of this research can provide a better understanding of the transmission behaviour of ultrasonic guided waves propagating through welded joints with defects. The method could be used for improving the performance of guided wave damage detection methods.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.286-288
• /
• 2006

The metallurgical and mechanical properties of fiction stir welded 304 austenitic stainless steel and AISI 1018 steel for fundamental study. Single-pass bead on plate weldments in the two steels were successfully achieved. The joints were evaluated by microscopy and hardness tests of the transverse cross section and transverse tensile tests.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.561-565
• /
• 2010

Stainless steel sheets are widely used as structural materials for the manufacture of railroad cars and commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. For the fatigue design of gas welded joints such as fillet joints and plug joints, it is necessary to obtain information on the stress distribution at the weldment and the fatigue strength of the gas welded joints. Moreover the influence of the geometrical parameters corresponding to the gas welded joints on the stress distribution and fatigue strength must be evaluated. ${\Delta}P-N_f$ curves were obtained from the data recorded in fatigue tests. Using these results, the ${\Delta}P-N_f$ curves were rearranged according the relation between $\Delta\sigma-N_f$ and the maximum stress at the edge of the fillet welded joint.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.457-463
• /
• 2016

The newly developed super ductile duplex stainless steel (SDSS) has good strength and ductility, and it can be used to reduce weight and improve the fabrication efficiency of a carbody of a rolling stock. In this study, spot weldability tests were conducted to take advantage of SDDSS in a carbody for an intermodal tram. Specimens of various thickness (0.4 to 5.0 mm) were prepared to find the proper welding conditions, and tensile load tests were conducted to evaluate the tensile-shear strength of spot welded joints. Then, nugget diameters were measured to verify the quality. The tensile-shear strength was found to be proportional to the heat parameter. It was verified that the tensile-shear strengths and nugget sizes of the joints satisfy the standard requirements. The overall weldability tests confirmed that SDDSS can be used effectively for the carbody of an intermodal tram.

• Wind and Structures
• /
• v.32 no.1
• /
• pp.55-69
• /
• 2021

Ultrapure ferritic stainless steel provides a new generation of long-span metal roof systems with continuous welding technology, which exhibits many unknown behaviors during wind excitation. This study focuses on the wind-resistant capacity of a new continuous welding stainless steel roof (CWSSR) system. Full-scale testing on the welding joints and the CWSSR system is performed under uniaxial tension and static ultimate wind uplift loadings, respectively. A finite element model is developed with mesh refinement optimization and is further validated with the testing results, which provides a reliable way of investigating the parameter effect on the wind-induced structural responses, namely, the width and thickness of the roof sheeting and welding height. Research results show that the CWSSR system has predominant wind-resistant performance and can bear an ultimate wind uplift loading of 10.4 kPa without observable failures. The welding joints achieve equivalent mechanical behaviors as those of base material is produced with the current of 65 A. Independent structural responses can be found for the roof sheeting of the CWSSR system, and the maximum displacement appears at the middle of the roof sheeting, while the maximum stress appears at the connection supports between the roof sheeting with a significant stress concentration effect. The responses of the CWSSR system are greatly influenced by the width and thickness of the roof sheeting but are less influenced by the welding height.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.179-183
• /
• 2007

A plate heat exchanger (PHE) normally uses vacuum brazing technology for connecting plates and fins. However, the reliability of high temperature brazing, especially with nickel-based filler metals containing boron the formation of brittle intermetallic compounds (IMCs) in brazed joints is of major concern. since they considerably degrade the mechanical properties. This research was examined the vacuum brazing of commercially SUS304 stainless steel with BNi-2 (Ni-Cr-B-Si) filler metal, and discussed to determine the influence of brazing temperatures on the microstructure and mechanical strength of brazed joints. In the metallographic analysis it is observed that considerable large area of Cr-B intermetallic compound phases at the brazing layer and the brazing tensile strength is related to removal of this brittle phase greatly. The mechanical properties of brazing layer could be stabilized through increasing the brazing temperature over $100^{\circ}C$ more than melting temperature of filler metals, and diffusing enough the brittle intermetallic compound formed in the brazing layer to the base metal.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.679-684
• /
• 2011

Recently, STS 301L joints of side panels to frames for stainless steel rolling stock have been made out by using existing welding methods including Resistance Spot Welding, Laser Welding and Arc Welding. Most of the processes were jointed by spot welding because it is faster at welding and comparatively less expensive for investment in welding facilities than other methods. During spot welding, however, indentation of the metal surface was made due to pressure and melting property of welding. Moreover, since the melting metal was forced to periphery of the plate as indentation was made, sheet separation, which cracked apart between jointed sheets, was carried out. A slight deformation which resulted from sheet separation deteriorated the emotional quality of railway vehicles. This paper suggests that by processing conventional spot electrode tip appropriately, melting metal is able to push up around the processed part (Hollow Spot Electrode Tip) and prevent from being dislodged from first place to periphery. Consequently, sheet separation is remarkably decreased. Also, the emotional quality of appearance of stainless steel rolling stock is enhanced considerably.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.447-452
• /
• 2003

Crevice corrosion is localized form of corrosion usually associated with a stagnant solution on the micro-environmental level. Such stagnant micro environments tend to occur in crevices (shielded areas) such as those formed under gaskets washers insulation material. fastener heads. surface deposits. disbonded coatings. threads. lap joints and clamps. Crevice corrosion is initiated by changes in located electrochemical reaction within the crevice such as a) depletion of inhibitor in the crevice b) depletion of oxygen in the crevice c) a shift to acid conditions in the crevice and d) build-up of aggressive ion species (e.g chloride) in the crevice. In this study. the mechanism of crevice corrosion for Type 430 stainless steel is investigated undercondition that the size of specimen is $15{\times}20\{times}3mm$, in 1N $H_2SO_4$ + 0.05N NaCl solution. and the artificial crevice gap size of 3 x 0.2 x 15 mm. Crevice corrosion is measured under applied potential -300mV(SCE) to the external surface. The obtained result of this study showed that 1) the induced time for initiation of crevice is 750 seconds. 2) potential of the crevice was about from -320mV to -399mV. which is lower than that of external surface potential of -300mV It is considered that potential drop in the crevice is one of mechanisms for the crevice corrosion

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4398-4404
• /
• 2015

Stainless steel sheets are widely used as the structural material for dynamic machine structures, These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding, For fatigue design of gas welded joints such as various type joint. It is necessary to obtain design information on stress distribution at the weldment as well as fatigue strength of gas welded joints. Thus in this paper, ${\Delta}P-N_f$ curves were obtained by fatigue tests. and, ${\Delta}P-N_f$ curves were rearranged in the ${\Delta}{\sigma}-N_f$ relation with the hot spot stresses at the gas welded joints. Using these results, the accelerated life test(ALT) is conducted. From the experiment results, an life prediction model is derived and factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of welded joints and data analysis by statistic reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.