• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1019-1022
• /
• 2004

High performance p-ch poly-Si TFTs with excellent stability were developed. By using a frequency doubled DPSS CW laser, the a-Si on glass could be crystallized into one dimensional single crystalline silicon named as a sequential lateral crystallization (SLC) region. We fabricated p-ch TFTs on SLC region and the typical characteristic values of the TFTs were $u_{fe}$ = 180 $cm^2$/Vs, $V_{th}$ = -3 V, S.S. = 0.5 V/dec, and $I_{off}$ = 1 pA/um@ $V_d$ = -10V. It is found that the TFTs are very stable after bias stresses such as negative and positive gate biases, hot carrier bias and high current bias. These results indicate that the poly-Si in SLC region is suitable for system on glass (SOG) application.

• Journal of Power Electronics
• /
• 제14권6호
• /
• pp.1208-1216
• /
• 2014

Mismatch between switching frequency and circuit parameters often occurs in industrial applications, which would lead to instability phenomena. The bifurcation behavior of $V^2$ controlled buck converter is investigated as the pulse width modulation period is varied. Nonlinear behavior is analyzed based on the monodromy matrix of the system. We observed that the stable period-1 orbit was first transformed to the period-2 bifurcation, which subsequently changed to chaos. The mechanism of the series of period-2 bifurcations shows that the characteristic eigenvalue of the monodromy matrix passes through the unit circle along the negative real axis. Resonant parametric perturbation technique has been applied to prevent the onset of instability. Meanwhile, the extended stability region of the converter is obtained. Simulation and experimental prototypes are built, and the corresponding results verify the theoretical analysis.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.76-83
• /
• 2003

Recently, the field of the engineering has been studied about optimum design continuously. Verified data by comparison with simulation and dynamic characteristic analysis enables the design of a machine tool to be modified easily and effectively concerning to the mode shape of the vibration. Especially, BC-500 Line Center has got some problems causing vibration which mainly come from Column and ATC part. So it is necessary to solve those problems by the two kinds of method such as changing structural design and reinforcing with ribs. In this paper, column and ATC part of BC-500 Line center are modified by an optimum design by the analysing method of FEM to avoid vibration. As a result, a more stable machine tool was designed by this simulation as optimum condition.

• 한국세라믹학회지
• /
• 제40권11호
• /
• pp.1062-1066
• /
• 2003

Design of a piezoelectric actuator for the ultrasonic motor must ensure that contact point has elliptic trajectory of movement. The new idea of an elliptic trajectory formation of the piezoelectric actuator is investigated in the paper. Shaking beam for the piezoelectric linear ultrasonic motor was introduced to realize this new idea. The principle is based on the excitation of longitudinal and flexural vibrations of the actuator by using two sources of longitudinal mechanical vibrations shifted by $\pi$/2. Mode-frequency and harmonic response analyses of the actuator based on FEM have been carried out. The moving trajectory of the contact point has been defined. Finally, The experimental research of shaking beam has been confirmed an opportunity of the elliptic trajectory reception with the help of one stable mode of the vibrations.

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.51-57
• /
• 2011

A power supply for magnetic-stimulation devices was designed via a control algorithm that involved a start current application based on a resonant converter. In this study, a new power supply for magnetic-stimulation devices was designed by controlling the pulse repetition frequency and pulse width. The power density could be controlled using the start-current-compensation and ZCS (zero-current switching) resonant converter. The results revealed a high-repetition-frequency, high-power magnetic-stimulation device. It was found that the stimulation coil current pulse width and that pulse repetition frequency could be controlled within the range of 200-450 ${\mu}S$ and 200-900 pps, respectively. The magnetic-stimulation device in this study consisted of a stimulation coil device and a power supply system. The maximum power of the stimulation coil from one discharge was 130 W, which was increased to 260 W using an additional reciprocating discharge. The output voltage was kept stable in a sinusoidal waveform regardless of the load fluctuations by forming voltage and current control using a deadbeat controller without increasing the current rating at the starting time. This paper describes this magnetic-stimulation device to which the start current was applied.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.35-38
• /
• 2005

In this study, S-Band receiver for low orbit satellite is implemented. The developed receiver is double super-heterodyne type and STDN compatible. Input/output frequency of receiver is 2034.747MHz and 18.414MHz used for KOMPSAT 2 satellite. Overall gain(@AGC=0V) and image rejection were 92.4dB and 50.2dB respectively. It was verified that receiver has stable performance to the temperature limit, power supply voltage variation and input signal level range.

• 전기학회논문지
• /
• 제68권1호
• /
• pp.1-7
• /
• 2019

Due to the highly concentrated power plants integrated through the limited transmission lines in Korea, a Special Protection System(SPS) has been applied to stabilize the power systems by instantly tripping the pre-determined generators in a large-scaled power plant when a fault occurs on the drawing transmission lines. Moreover, power outputs of those generators are constrained to avoid any activation of Under Frequency Load Shedding(UFLS) even after those generators are tripped by SPS action. For this, this paper proposes a method for calculating the required capacity of Energy Storage System(ESS) expected to relieve the operating constraints to generators using its fast response for controlling power system frequency. The proposed method uses the generator acceleration energy to derive the stable condition during the SPS action. In addition, its effectiveness is verified by the case studies adopting actual SPS operations in Korean power systems.

• 한국생활과학회지
• /
• 제17권5호
• /
• pp.927-938
• /
• 2008

The purpose of this study was to classify self-efficacy typology and analyze the relationship between self-efficacy and consumption value of college students as consumers. Data were gathered by surveying college students living in Daegu and Kyungbook area using convenient sampling. 513 questionnaires were used in the statistical analysis. Data were analyzed by frequency, factor analysis, cluster analysis, correlation analysis, ANOVA, and Duncan-test. The findings are as follows. The self-efficacy typologies of college students were classified into three groups such as challenging confident accomplish oriented, stable uncertain accomplish oriented, and stable accomplish oriented. In the relationship of the self-efficacy was related to the sub-variables of consumption value. The self-efficacy oriented group showed different all the sub-variables of consumption value factors.

• 센서학회지
• /
• 제17권1호
• /
• pp.75-80
• /
• 2008

In this work, we optimized a microbolometer for application of a $CO_2$ detector by using MEMS technology. We fabricated a stable thermal isolation structure by varying the lengths of supporting legs which affect bolometer performance. We could fabricate more stable thermal isolation structure for the microbolometer through the results of ANSYS simulations, and minimize the fabrication processes by using bulk micromachining to use a $CO_2$ detector. The microbolometer shows a detectivity of $2.5{\times}109$ cmHz$^{1/2}$/W at a chopper frequency of 8 Hz and a bias current of $6.25\;{\mu}A$ with a vacuum package of about $3.0{\times}10.3$ torr. Therefore, we put to conclusion that the microbolometer optimized in this experiment could be useful for the application of a $CO_2$ detector.

• 한국토양비료학회지
• /
• 제45권6호
• /
• pp.1153-1156
• /
• 2012

대관령 지역의 과거 38년간 (1972-2009)의 기상자료를 수집하여 최저한계온도를 추정하였다. 최저한계온도 출현 빈도 추정은 Gumbel의 극한치 확률분포이론을 도입하여 기온자료의 확률분포함수를 도출하여 이루어졌다. 그 결과 저온 출현일 빈도는 작물의 생산안정성과 밀접한 관계가 있기 때문에 조사하였으며, 저온 출현일이 앞당겨질수록 작물을 일찍 심어 안정된 생육을 유지할 수 있어 그 만큼 수량을 높일 수 있을 것으로 판단되었다. 대관령 지역에서 한계 저온 $5^{\circ}C$ 이상이 5일 이상 지속되는 날짜를 보면 4월 3일, 4월 10일, 4월 20일, 4월 28일, 5월 8일로 나타났으며, 한계저온이 나타나는 시기가 앞으로 당겨질수록 그 시기 (한계저온 $5^{\circ}C$ 출현일)가 출현할 확률이 작아지고 재현되는 기간이 길어져, 작물을 재배할 기회가 줄어들어 작물 파종 및 정식이 어렵게 된다. 따라서 재현기간을 순서대로 보면 50, 25, 10, 5, 2년 이었다. 기온 $5^{\circ}C$에 적응하는 저온성 작물 (배추, 샐러리, 토마토, 딸기 등)은 5월 8일 이후에 파종 또는 정식하면 대관령 지역에서 안정된 수량을 얻을 수 있을 것으로 판단되었다.