• Journal of Welding and Joining
• /
• v.12 no.1
• /
• pp.94-101
• /
• 1994

In this study, plasma spraying has been used to produce $TiO_2$ polycrystalline coatings from $TiO_2$ powders. The physical and chemical properties of plasma sprayed $TiO_2$ coatings depend greatly on plasma spraying conditions. The electrical resistivity, oxygen concentration, photocurrent and crystal structure of plasma sprayed $TiO_2$ coating has been studied. The results are as follows: 1. The oxygen loss and electrical conductivity of $TiO_2$ plasma sprayed coatings increased by low pressure and high amount of auxiliary gas, hydrogen in plasma spraying. 2. Oxygen loss increase electrical conductivity, and decrease photocurrent of $TiO_2$ plasma sprayed coatings. 3. Photocurrent of $TiO_2$ plasma sprayed coatings manufactured in atmospheric pressure is higher than that of low pressure.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.67-76
• /
• 1998

Friction materials for brake linings and clutches have severe performance requirements. The principal function of such frictional elements is to convert kinetic energy to heat, and then either to absorb or to dissipate heat. In order to achieve these objectives, the coefficient of friction must be as high as possible, independent of variations in operating conditions, and the necessary energy conversion must be accomplished with a minimum of wear on the contacting parts. In this study, Al powder, Al bronze powder and Mo powder used in general for automobile brake was sprayed on automobile brake disc to restrain rust and to maintain friction performance. Dynamo and corrosion tests have been carried out. It is concluded that the sprayed disc with Al bronze powder has the most improved frictional performance and anti-corrosive characteristics. The main results obtained can be summarized as follows; 1. From the corrosion current density test for gray cast iron and sprayed disc with powders of Al, Al bronze and Mo, it was cleared that the spray treatment with Al bronze powder showed the most superior anti-corrosive characteristics than other powders. 2. By anode polarization toward the noble direction from corrosion potential, corrosion current density with sprayed brake disc by Al-bronze powder was the lowest. 3. Mean frictional coefficients obtained from dynamo test are as follows : the sprayed disc with Al(99.99%) powder was 0.190 ; the sprayed disc with Al-bronze powder was 0.312 ; the sprayed disc with Mo powder was 0.257 ; the non-sprayed disc of gray cast iron was 0.331. In the case of the sprayed disc Al-bronze powder showed the most excellent frictional characteristics . 4. Amount of burnish quantity obtained from burnish test by dynamometer is as follows : the sprayed disc with Al-powder was 1.079 mm : the sprayed disc with Al-bronze powder was 0.155 mm : the sprayed disc with Mo powder was 0.253 mm : the non-sprayed disc of gray cast iron was 0.241 mm. Al-bronze powder also showed the most excellent burnish characteristics.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.3
• /
• pp.3053-3058
• /
• 1973

1. This study was conducted to examine the effects of change of the short range nozzle hole on the travelling distance. The results of this study are summarized as follows; a) Effect of change of the cap hole diameter on the travelling distance of sprayed particles was generally a linear, the increasing rate was about 0.27. b) When the difference between the sectional area of cap hole and that of grooves of swirl plate, was small the travelling distance was decreased by the decreasing of spraying speed at cap hole. 2. This study was conducted to examine the effects of change of the short range nozzle hole on the size of spraying particles. The results of this study are summarized as follows; a) The diameter of sprayed particles on travelling distances in the short range nozzle did not coincide with the kinetic energy principle derived from the momentum and the resistance. b) The average diameter of sprayed particle between 1m and 3m in which amount of sprayed particle was particularly a great deal, was big, because that some of sprayed particles were absorbed each other on the way to fall c) Effect of increase of cap hole diameter was generally enlarged the average diameter of sprayed particle with small rate.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.234-235
• /
• 2006

In this study, the plasma sprayed $Al_2O_3$ and $Y_2O_3$ coatings have been investigated for applications of microelectronic components. The plasma sprayed coatings had a well-defined splatted lamellae microstructure, intersplat pores and a higher amount of microcracks within the splats. The plasma sprayed $Y_2O_3$ coating had a relatively lower hardness of 300-400Hv, compared to 650-800Hv for $Al_2O_3$ coating, and would be readily damaged by mechanical attacks such as erosion, wear and friction. For a reactive ion etching against F-containing plasmas, however, the $Y_2O_3$ coating had a much higher resistance than the $Al_2O_3$ coating because of the reduced erosion rate of by-products.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.2
• /
• pp.2980-3001
• /
• 1973

Nozzle is a part of sprayer and is consists of several elements; swirl plate, vortexchamber, cap and body. The travelling distance of sprayed particles is important in the wide reach nozzle. The factors to influence the travelling distance of the sprayed particles may be the helical angle of swirl plate, the distance of vortex hamber, the slope and the size of cap hole. The study was conducted to examine the effects of these factors on the travelling distance. The results of this study are summarized as follows; 1) There was higher positive correlation(+0.96) between the maximum travelling distance for which amount of sprayed particles was 5cc/cm min. and centro-position of the travelling distance. 2) There was a higher positive correlation(+0.85) between total discharge of sprayed particles and the centro-position of the travelling distance. 3) Main effects and interaction effects of helical angle, pressure, vortex chamber distance and cap slope were significantly affected the travelling distance of sprayed particles. 4) Main effects of helical angle, pressure and cap slope were especially highly significant to influence the travelling disance. 5) Helical angle, pressure, vortex chamber distance and cap slope influenced spraying forward velocity of dise hole, among which cap slope and pressure of nozzle was the most important factors. 6) Effect of change of helical angle on the travelling distance of sprayed particles, was generally a quadratic, the least value of the distance being showed about $45^{\circ}$ and the largest at about $15^{\circ}\;and\;55^{\circ}$, the decreasing rate of the change between $15^{\circ};and\;25^{\circ}$ was very small. 7) Effect of change of pressure on the travelling distance sprayed particles was generally a linear, the increasing rate of the charge was about 1.68, which was the most effective compared to the change of the other factors. 8) Effect of change of vortex chamber distance on the spraying distance was also generally a linear, the increasing rate being about 0.16, which was the least effective. 9) Effect of change of cap slope on the travelling distance was also generally a linear, the increasing rate was about 0.61 and its effect was about medium.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.1
• /
• pp.171-178
• /
• 1994

This paper reports histologic and histomorphometric results concerning bone healing around vent area of 16 titanium plasma sprayed IMZ implants in rabbit femurs. Bone contact around the implants 8 weeks after placement showed a great deal of variability from 14.32% to 65.94% and mean total bone contact was 33.96%. The mean percent amount of bone contact was 43.68% in inner surface of vent and 27.79% in outer surface. Histologic examination of horizontal sections of vent area showed direct contact with living lamellar bone and some woven bone. The implants surface area not in contact with bone was in contact with collagenous connective tissue. But there was no sign of foreign-body reaction.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.610-618
• /
• 1998

Alumina were added to ceria based ceramic powders upto 9.7 vol% and composite powders were sprayed by plasma spraying process in order to improve the mechanical properties such as hardness fracture tough-ness and thermal shock resistance. The ceria based coating sprayed without alumina has the typical colum-nar and lamellar structure. Alumina addition has lowered the amount of columnar and lamellar sturcture Added alumina was segreagated in the grain boundary and grain of ceria based crystal accompanied with pore. The maximum value of density and the minimum value of porosity were observed at the sprayed coating with 4.8 vol% alumina. The hardness fracture toughness and thermal shock resistance were increased with alumina addition. The improvement of mechanical properties of plasma sparyed ceria based coatings result-ed from the disapperance of the columnar and lamellar sturcture by addition of alumina.

• Journal of Korean Society of Forest Science
• /
• v.107 no.2
• /
• pp.229-236
• /
• 2018

Pesticides are widely sprayed by the growers in street trees and planting areas which include urban forests, community forests and city parks to control pests. Spraying pesticides not only affect the people who sprayed but also affect the unspecified citizens who's are exposed to pesticides sprayed trees by contact or inhalation. A few studies have been conducted to measure the amount of pesticides in forest area but no studies have been conducted to measure the pesticide amount in tree in public living space. So, in our study, we investigated the amount of pesticides in cotton gloves, in leaf residue, and respiratory exposure for a certain period of time after applying Fenitrothion EC to Korean boxweed tree (Buxus Koreana) to know the safety time of pesticides after spraying. We found that, up to 4d, there was no significant difference of the amount of Fenitrothion on leaves. But the amount of pesticides on gloves was significantly higher on 1h ($510.1{\mu}g$) and 24h ($405.4{\mu}g$) than 48h ($45.0{\mu}g$) after spraying. The amount of pesticides on inhalation was also significantly higher in 1 h ($0.2{\mu}g$) and 24 h ($0.1{\mu}g$) than 48 h after spraying. After 48h, we did not find pesticides amount in inhalation. Thus, we was considered necessary to pay attention to 48h after spraying of pesticide Fenitrothion.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.4
• /
• pp.412-418
• /
• 2009

This study is conducted in order to know the residue patterns of insecticide cypermethrin and fungicide diethofencarb in ginseng sprayed by various application methods. Two pesticides were sprayed separately on ginseng using traditional, soil and vinyl mulching applications. The vinyl mulching application was that head part of ginseng protected from pesticides. When cypermethrin was sprayed on ginseng by traditional application, its residue amount in ginseng was 0.25 mg/kg which exceeded 0.1 mg/kg, maximum residue limit(MRL) established by Korea Food & Drug Administration(KFDA). But in case of vinyl mulching and soil application, its residue amounts were 0.04 and 0.07 mg/kg, respectively. The residue amount of diethofencarb in ginseng was 3.01 mg/kg which exceeded the MRL, 0.3 mg/kg. Further, in case of vinyl mulching and soil application, its residue amounts were 1.71 and 9.39 mg/kg which exceeded the MRL 0.3 mg/kg. Although the residue amounts of both pesticides exceeded the MRLs for ginseng, we can explain that pesticides remained in head part of ginseng is probably the reason why higher pesticides residue levels were observed.

• Korean Journal of Medicinal Crop Science
• /
• v.16 no.6
• /
• pp.390-396
• /
• 2008

The aim of this work is to assess the safety of fungicide tolclofos-methyl, difenoconazole and azoxystrobin in ginseng sprayed by safe use guideline. When tolclofos-methyl was sprayed on ginseng by safe use guideline, the residue amounts (MRL) of it in ginseng was 0.13 mg/kg which is below than 0.3 mg/kg, maximum residue limit established by Korea Food & Drug Administration (KFDA). The residue amounts of ginseng parts, head part was 0.37 mg/kg and main body part was 0.13 mg/kg. In case of difenoconazole, the residue amounts in ginseng was 0.81 mg/kg. which was exceed the MRL, 0.2 mg/kg. By the analyze results of ginseng part, the residues of head and main body part were 3.01 and 0.40 mg/kg, respectively. In experiment of vinyl mulching, the residue amount of difenoconazole in ginseng was 0.05 mg/kg. The residue amounts of azoxystrobin in ginseng sprayed by safe use guideline was 0.14 mg/kg. This residue was not exceed the MRL 0.5 mg/kg. The residue amounts by ginseng parts was 0.51 mg/kg for head part and 0.28 mg/kg for main body part. In case of vinyl mulching, the residue amount of azoxystrobin was 0.02 mg/kg.