• 한국분무공학회지
• /
• 제19권4호
• /
• pp.167-173
• /
• 2014

The spray characteristics of Gas-Centered Swirl Coaxial Injector was investigated that there were different characteristics with or without gas flow. As gas flow was accelerated, the momentum of gas was transferred to the momentum of liquid in the low liquid Reynolds number. Therefore, the axial velocity of liquid was increased and the measured value was smaller than without gas flow. However, in the high momentum flux ratio, the momentum transfer hardly occurred and the results had constant values. As the recess length was increased, the mixing area of gas and liquid also was increased, the results were decreased.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.71-74
• /
• 2008

NUFLEX is a general purpose thermo/fluid flow analysis program which has various physical models including spray. In NUFLEX, spray models are composed of breakup and collision models of droplet. However, in case of diesel engine, interaction between wall-film and impingement model considering heat transfer is not coded in NUFLEX. In this study, Lee & Ryou impingement & wall-film model considering heat transfer is applied to NUFLEX. For the verification of this NUFLEX program, numerical results are compared with experimental data. Differences of film thickness and radius between numerical results and experimental data are within 10% error range. The results show that NUFLEX can be used for comprehensive analysis of spray phenomena.

• 산업기술연구
• /
• 제32권A호
• /
• pp.29-33
• /
• 2012

We demonstrated the viability of fully microfabricating SWCNT(single-wall carbon nanotube) film strain sensors for force and weight sensing. Our spray-deposited SWCNT film strain sensors showed good linearity over a range from 0 to 400 microstrain, and much higher sensitivity compared to commercial metal foil-type gauges. The number of grids and the thickness of the SWCNT film were found to have a significant effect on the strain sensing properties of the SWCNT film gauges. A strain sensing methode for the CNT-based strain gauges was also investigated using a binocular type beam load cells. Preliminary results indicate that the microfabrication method shown here is promising for developing a commercial strain gauge using a spray-coated SWCNT thin film. In the near future, various studies will be performed to further enhance the properties of the spray-coated SWCNT film strain sensors.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.951-961
• /
• 2001

The present article presents an extension to the computational model for spray/wall interaction and liquid film processes that has been dealt with in the earlier studies (Lee and Ryou, 2000a). The extensions incorporate film spread due to impingement forces and dynamic motion induced by film inertia to predict the dynamic characteristics of wall films effectively. The film model includes the impingement pressure of droplets, tangential momentum transfer due to the impinging droplets on the film surface and the gas shear force at the film surface. Validation of the spray/wall interaction model and the film model was carried out for non-evaporative diesel sprays against several sources of experimental data. The computational model for spray/wall interactions was in good agreement with experimental data for both spray radius and height. The film model in the present work was better than the previous static film model, indicating that the dynamic effects of film motion should be considered for wall films. On the overall the present film model was acceptable for predication of the film radius and thickness.

• 한국추진공학회지
• /
• 제10권3호
• /
• pp.9-17
• /
• 2006

본 연구는 케로신-LOX를 추진제로 하는 액체로켓엔진용 스월 동축형 인젝터의 리세스 길이에 따른 분무특성 파악을 목표로 하였다. 리세스 길이에 따른 두 추진제의 내부충돌현상에 의한 ripple의 형성과 감쇠가 인젝터 외부의 분무안정성에 영향을 미치므로 분무특성과 큰 연관성을 가진다. 또한, 리세스 길이가 증가함에 따라 평균액적크기는 증가하였으며, 혼합효율은 증가하다가 최대값에 도달한 후 다시 감소하는 경향성을 보였다.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.22-30
• /
• 2011

추력변화를 위한 방법에는 여러 가지가 있는데, 고압력 강하 시스템, 이중 매니폴드 분사기, 가스 분사, 다중 챔버, 펄스 추력, 움직이는 분사기 구성요소 등이 있다. 이 중에서 이중 매니폴드 분사기의 경우에는 하나의 분사기 구조에 서로 다른 두 개의 매니폴드를 가지는 분사기를 결합하는 방식의 분사기인데, 각 분사기는 각각의 연료 공급시스템을 독립적으로 가지고 있어 각 매니폴드마다 독립적으로 유량을 조절 할 수 있다. 본 논문에서는 이중 매니폴드 분사기를 사용하여 넓은 추력범위에서 연료분사의 안정성을 판단하기 위하여 각 매니폴드의 접선방향 유입구 넓이의 비와 분사압력에 따라 분사 형상을 측정하고, 분사기 오리피스 끝단에서 액막 두께를 측정하였다.

• 한국분무공학회지
• /
• 제26권1호
• /
• pp.26-32
• /
• 2021

In this study, the thickness of the liquid sheet formed by two low speed impinging jets was measured by the direct contact method. The effects of jet velocity and liquid viscosity on the thickness were analyzed and the results were compared with theoretical modeling and optical thickness measurement results. The liquid film thickness decreased as the radius and circumferential angle increased. The jet velocity did not affect the liquid film thickness as predicted in theoretical modeling. In the theoretical modeling, there was no influence of the fluid properties on thickness, but in the case of low viscosity liquids, the thickness was predicted high, and it was well matched in high viscosity liquids. The direct measurement results showed no significant difference from the optical measurement results, thus confirming the reliability of the optical measurement method.

• 한국세라믹학회지
• /
• 제36권6호
• /
• pp.625-631
• /
• 1999

Ceramic tapes were fabricated by ultrasonically spraying slurries of monodispersed spherical and alumina powders. Effects of slurry compositions on tape forming were investigated. A relatively fast rate of solvent evaporation caused pores and cracks to be formed. A good chemical affinity between solvent and binder gave rise to binder separation resulting in inhomogeneous distribution of binder. Defect-free silica tapes with uniform distribution of particle packing and the binder were obtained from the solvent having a low chemical affinity and a slow evaporation rate and containing appropriate amounts of the binder and the plasticizer. Tape thickness could be controlled by adjusting solids loadings and slurry feed rates. It was possible to fabricate a tape in 15 $\mu\textrm{m}$ thickness from 7 vol% alumina slurry.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.29-33
• /
• 2010

본 연구는 Kerosene-LOx를 추진제로 하는 가스발생기용 스월 동축형 인젝터의 리세스 길이에 따른 내부 유동의 특성 파악을 목표로 하였다. 리세스 길이는 분무 안정성, 내부 LOx post 손상 등에 영향을 미치는 중요한 요소로 액막두께, 매니폴드 압력 측정 및 내부 유동 가시화를 통해 리세스의 영향을 분석하였다. 또한, 리세스 길이에 따른 내부 또는 외부 인젝터 각각의 분무특성도 살펴보았다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2007년도 High Temperature Superconductivity Vol.XVII
• /
• pp.79-79
• /
• 2007