• 콘크리트학회논문집
• /
• 제20권3호
• /
• pp.325-333
• /
• 2008

본 연구에서는 강섬유와 서로 다른 직경 및 길이를 가진 폴리프로필렌섬유를 혼합한 하이브리드 섬유보강 콘크리트의 압축강도, 수축균열 및 고온에서 화재저항성을 평가하였다. 압축강도, 쪼갬인장강도, 휨시험 및 수축균열저항성을 평가하기 위하여 실시하였으며 또한 400$^{\circ}C$, 600$^{\circ}C$, 800$^{\circ}C$ 및 1,200$^{\circ}C$에 노출 후 물리 역학정 특성을 평가하기 위하여 표면관찰, 질량손실 및 잔류압축강도 시험을 실시하였다. 시험 결과 하이브리드 섬유보강 콘크리트는 역학적 성능, 수축균열저항성 및 화재저항성을 향상시켰으며 온도 변화에 따른 콘크리트의 성능 저하는 온도가 $600\sim800^{\circ}C$의 범위일 때 가장 컸다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권4호
• /
• pp.91-99
• /
• 2020

콘크리트용 앵커볼트는 콘크리트 구조물에 대한 비구조요소의 정착에 주로 사용되고 있으며, 시공성의 이점에 따라 후설치앵커가 주로 사용되고 있다. 앵커의 저항 성능과 관련하여 콘크리트 쪼개짐 영향을 최소화하기 위한 위험 연단거리가 제시되고 있지만 실제 앵커의 경우 이상적인 연단거리를 확보하기 어렵다. 즉, 인장 하중에 따라 발생 가능한 콘크리트 쪼개짐 등 복합적인 요소가 포함된 앵커의 저항 성능과 인장 거동 특성을 파악하기 위함이 본 연구의 목적이다. 표준시험방법을 바탕으로 인장실험을 진행하고 도출된 하중-변위 결과 및 파괴 형상을 분석하였다. 위험 연단거리가 확보되지 않은 앵커의 경우 인장력에 의해 콘크리트 쪼갬 파괴가 동반된 파괴 모드가 도출되고 저항 특성은 강성 구간으로 분류된다. 또한, 실험체 구성 요소를 바탕으로 비선형 유한요소모델을 구성하였으며, 앵커 거동을 모사하기 위해 구속 조건 및 연결요소 조건에 따른 경계조건별 변수 해석을 수행하였다. 이에 따라 도출된 해석 결과는 콘크리트 내부 파괴 영향성 및 실제 앵커의 거동을 바탕으로 검증하여 범용구조해석 프로그램 내 경계조건을 통한 저항 메커니즘 적용이 가능한 것으로 판단된다.

• Steel and Composite Structures
• /
• 제36권1호
• /
• pp.103-118
• /
• 2020

The static behavior of grouped large-headed studs (d = 30 mm) embedded in ultra-high performance concrete (UHPC) was investigated by conducting push-out tests and numerical analysis. In the push-out test, no splitting cracks were found in the UHPC slab, and the shank failure control the shear capacity, indicating the large-headed stud matches well with the mechanical properties of UHPC. Besides, it is found that the shear resistance of the stud embedded in UHPC is 11.4% higher than that embedded in normal strength concrete, indicating that the shear resistance was improved. Regarding the numerical analysis, the parametric study was conducted to investigate the influence of the concrete strength, aspect ratio of stud, stud diameter, and the spacing of stud in the direction of shear force on the shear performance of the large-headed stud. It is found that the stud diameter and stud spacing have an obvious influence on the shear resistance. Based on the test and numerical analysis results, a formula was established to predict the load-slip relationship. The comparison indicates that the predicted results agree well with the test results. To accurately predict the shear resistance of the stud embedded in UHPC, a design equation for shear strength is proposed. The ratio of the calculation results to the test results is 0.99.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.201-204
• /
• 2006

The shear resistance of RC beams is subject to the amount of shear-reinforcing bars ($p_w$) and yield strength ($f_{wy}$) as well as their interactive influence ($p_wf_{wy}$). Thus, it is reasonably expected that high-strength steel bars can greatly reduce the necessary amount of shear-reinforcing bars. On the other hand, although the bond strength is influenced by the amount of shear reinforcing bars, it is not affected by the yield strength. Thus, there is often an issue that bond failure occurs before shear failure depending on the arrangement of shear reinforcing bars. It is a common practice to set sub-ties for the transverse confinement of the main re-bars as a method to prevent the bond failure. However, it can also become a factor in decreased work efficiency due to the complexity of the construction. This study experimented with simultaneous use of high-strength transverse reinforcing bars ($f_{wy}=800MPa$) and U-shaped transverse reinforcing bars of regular strength ($f_{wy}=300MPa$) in an attempt to decrease the necessary quantity of shear reinforcing bars. The effect of this attempt was investigated through fundamental experimental research in terms of the improvement in shear resistance and bond strength as well as the ease of construction.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.653-658
• /
• 1999

Bond between reinforcing bars and the surrounding concrete is supposed to safely transfer load in the design process of reinforced concrete structures. Bond failure of reinforcing bars generally take place by splitting of concrete cover as bond force between concrete and reinforcing bars exceeds the resistance by the confinement of the concrete cover and transverse reinforcement. Confinement, concrete cover and transverse reinforcement, on bond are the key factor of current provision to determine development length of reinforcing bars to concrete. In this study, previous available data are analyzed with respect to the current provisions for development and splice of reinforcement. From this study, the new provision for the design are proposed, which will be efficient and effective with some specific limit value.

• 한국건축시공학회지
• /
• 제12권3호
• /
• pp.332-339
• /
• 2012

In this study, six mortar mixes were tested in order to examine the significance and limitations of hydrophilic fiber in terms of its capacity to enhance the tensile resistance of Hwangtoh mortar. Lyocell, polyamide and polyvinyl alcohol (PVA) fibers were selected for the main test parameters. The tensile capacity of mortars tested was evaluated based on the splitting tensile strength and the modulus of fracture, while their ductility was examined using the toughness indices specified in ASTM. Test results showed that the addition of lyocell and PVA fibers had little influence on the flow of the Hwangtoh mortars. To enhance the tensile capacity and toughness index of Hwangtoh mortar, it is proposed that fiber spacing above 0.0003 is required, regardless of the type of fiber.

• Structural Engineering and Mechanics
• /
• 제16권4호
• /
• pp.469-478
• /
• 2003

The primary aim of this study was to investigate the bond strength between reinforcement and concrete. Large sized nine beams, which were produced from concrete with approximately ${f_c}^{\prime}=30$ MPa, were tested. Each beam was designed to include two bars in tension, spliced at the center of the span. The splice length was selected so that bars would fail in bond, splitting the concrete cover in the splice region, before reaching the yield point. In all experiments, the variable used was the reinforcing bar diameter. In the experiments, beam specimens were loaded in positive bending with the splice in a constant moment region. In consequence, as the bar diameter increased, bond strength and ductility reduced but, however, the stiffnesses of the beams (resistance to deflection) increased. Morever, a empirical equation was obtained to calculate the bond strength of reinforcement and this equation was compared with Orangun et al. (1977) and Esfahani and Rangan (1998). There was a good agreement between the values computed from the predictive equation and those computed from equations of Orangun et al. (1977) and Esfahani and Rangan (1998).

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.489-492
• /
• 2006

Needs for the new technologies and cutting-edge Ultra Flowing Self-Compacting Concrete are emerging as the concrete structures are becoming bigger and more specialized recently. In North America and Europe, SCC, which has high resistance against flow ability and segregation, is being used as concrete material in applications such as precast and prestressed bridges, where reinforcing bars are overcrowdedly placed. In Korea, SCC has been utilized limitedly in building structures but its utilization should be expanded to engineering structures such as bridges. In this study, for the application in precast and prestressed bridges with overlycrowded reinforcing bars, USCC was mixed with admixtures to give a binary system and a ternary system according to the 1st grade rules by JSCE (Japan Society of Civil Engineers). Compressive strength and splitting tensile strength of the resulting USCCs were tested. Elastic modulus were compared with the values suggested in CEB-FIP code and ACI 318-05.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.394-394
• /
• 2013

The spin-orbit interaction has received great attention in the field of spintronics, because of its property and applicability. For instance, the spin-orbit interaction induces spin precession which is the key element of spin transistor proposed by Datta and Das, since frequency of precession can be controlled by electric field. The spin-orbit interaction is classified according to its origin, Dresselhaus and Rashba spin-orbit interaction. In particular, the Rashba spin-orbit interaction is induced by inversion asymmetry of quantum well structure and the slope of conduction band represents the strength of Rashba spin-orbit interaction. The strength of spin-orbit interaction is experimentally obtained from the Shubnikov de Hass (SdH) oscillation. The SdH oscillation is resistance change of channel for perpendicular magnetic field as a result of Zeeman spin splitting of Landau level, quantization of cyclotron motion by applied magnetic field. The frequency of oscillation is different for spin up and down due to the Rashba spin-orbit interaction. Consequently, the SdH oscillation shows the beat patterns. In many research studies, the spin-orbit interaction was treated as a tool for electrical manipulation of spin. On the other hands, it can be considered that the Rashba field, effective magnetic field induced by Rashba effect, may interact with external magnetic field. In order to investigate this issue, we utilized InAs quantum well layer, sandwiched by InGaAs/InAlAs as cladding layer. Then, the SdH oscillation was observed with tilted magnetic field in y-z plane. The y-component (longitudinal term) of applied magnetic field will interact with the Rashba field and the z-component (perpendicular term) will induce the Zeeman effect. As a result, the strength of spin-orbit interaction was increased (decreased), when applied magnetic field is parallel (anti-parallel) to the Rashba field. We found a possibility to control the spin precession with magnetic field.

• 콘크리트학회논문집
• /
• 제22권4호
• /
• pp.519-525
• /
• 2010

FRP 보강근의 정착과 이음에 대한 국내외 실험을 수집하고, 정착과 이음실험을 분리한 회귀분석을 통해 쪼갬파괴에 의한 정착길이 설계식과 이음길이 설계식을 제안하였다. 이음실험에 의한 평균 부착강도는 정착실험에 의한 평균 부착강도에 비해 낮으며, C/$d_b$에 크게 영향을 받는 것으로 평가되었다. 따라서 합리적인 이음길이 설계를 위해 이음실험만으로 구성된 데이터에 근거한 이음길이 설계식을 개발할 필요가 있다. 또한 부착강도의 분산(分散)이 FRP 보강근의 인장강도 분산에 비해 크므로, 정착길이와 이음길이 설계식에 이를 반영한 안전율이 요구된다. 이 연구에서는 FRP 보강 콘크리트 구조물의 하중계수와 강도감소계수가 철근콘크리트구조와 동일하다는 조건에서, 철근 품질관리에 적용되는 5% 분위수를 이용하여 경제적이면서 신뢰성 높은 정착길이와 이음길이 설계식을 개발하였다. 제안된 이음길이 설계식은 정착실험을 중심으로 개발된 ACI 440 설계식보다 C/$d_b$의 영향을 정확하게 반영하여, C/$d_b$가 3.0 이상인 경우 ACI 440보다 짧은 이음길이가 산정된다. FRP 보강근이 주로 활용될 것으로 기대되는 외기에 노출된 슬래브와 벽체의 배근 특성을 고려하면 이 연구에서 제안된 설계식은 매우 경제적인 이음길이 설계를 가능하게 한다.