• Journal of the Korean Magnetics Society
• /
• v.18 no.2
• /
• pp.75-78
• /
• 2008

$AB_2X_4$(A, B=Transition Metal, X=O, S, Se) are cubic spinel normal ferrimagnets, in which M ions occupy the tetrahedral sites and Cr ions occupy the octahedral sites. Recently, they have been investigated for behaviour of B site ions and A-B interaction. Polycrystalline $[Co_{0.9}Zn_{0.1}]_A[Cr_{1.98}{^{57}Fe_{0.02}}]_BO_4$ compound was prepared by wet-chemical process. The ferrimagnetic transition was observed around 90K. $M\"{o}ssbauer$ absorption spectra at 4.2K show that the well-developed two sextets are superposed with small difference in hyperfine fields($H_{hf}$). The hyperfine fields of $CoCr_{1.98}{^{57}Fe_{0.02}}O_4$ and $Co_{0.9}Zn_{0.1}Cr_{1.98}{^{57}Fe_{0.02}}O_4$ were determined to be 488, 478 kOe and 486, 468 kOe, respectively. We notice that the one of the magnetic hyperfine field values changes with Zn ion substitution. These results suggest the incommensurate states and spin-reorientation temperature($T_S=18K$) changes with Zn ions substitution below spin-reorientation temperature($T_S=28K$) of $CoCr_{1.98}{^{57}Fe_{0.02}}O_4$

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.942-948
• /
• 2010

In this study we aims to examine the effects of 0.5 mol% $Cr_2O_3$ addition on the reaction, microstructure development, resultant electrical properties, and especially the bulk trap and interface state levels of ZnO-$Bi_2O_3-Sb_2O_3$ (Sb/Bi=0.5, 1.0, and 2.0) systems (ZBS). The samples were prepared by conventional ceramic process, and characterized by XRD, density, SEM, I-V, impedance and modulus spectroscopy (IS & MS) measurement. The sintering and electrical properties of Cr-doped ZBS (ZBSCr) systems were controlled by Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$) was decomposed more than $100^{\circ}C$ lowered on heating in ZBS (Sb/Bi=1.0) by Cr doping. The densification of ZBSCr (Sb/Bi=0.5) system was retarded to $800^{\circ}C$ by unknown Bi-rich phase produced at $700^{\circ}C$. Pyrochlore on cooling was reproduced in all systems. And $Zn_7Sb_2O_{12}$ spinel ($\alpha$-polymorph) and $\delta-Bi_2O_3$ phase were formed by Cr doping. In ZBSCr, the varistor characteristics were not improved drastically (non-linear coefficient $\alpha$ = 7~12) and independent on microstructure according to Sb/Bi ratio. Doping of $Cr_2O_3$ to ZBS seemed to form $Zn_i^{..}$(0.16 eV) and $V^{\bullet}_o$ (0.33 eV) as dominant defects. From IS & MS, especially the grain boundaries of Sb/Bi=0.5 systems were divided into two types, i.e. sensitive to oxygen and thus electrically active one (1.1 eV) and electrically inactive intergranular one (0.95 eV) with temperature.

• Economic and Environmental Geology
• /
• v.30 no.5
• /
• pp.477-491
• /
• 1997

In the Bibong area of the western part of Chungcheongnam-do, ultramafic masses occur as discontinuous isolated lenticular bodies in the Precambrian Kyeonggi gneiss complex. They extend for about 200 m long to NNE directions which are parallel to fault lines in the gneiss complex. The ultramafic masses contact with the adjacent gneiss complex as steeply dipping faults. They are dunites and harzburgites and many of them are partially or completely serpentinized. The ultramafic rocks dominantly show protogranular, equigranular and equigranular-$m{\grave{o}}saic$ textures. They also show porphyroclastic (megacrystic) or recrystallized textures reflecting several stages of metamorphism. They contain varying amounts of olivine $(Fo_{89-92})$, enstatitic to bronzitic orthopyroxene, diopsidic clinopyroxene, tremolitic to pargasitic hornblende, and spinel with serpentine, talc, chlorite, calcite and magnetite. The ultramafic rocks have high magnesium numbers and transitional element contents, low alkali contents and show deplete REE patterns. Comparing with available data, geochemical and mineralogical characteristics shown in the ultramafic rocks of the Bibong area are similar to those of worldwide mantle xenoliths and orogenic related ultramafic rocks. The field evidences, petrographical, geochemical and mineralogical characteristics shown in the ultramafic rocks of the Bibong area are similar to alpine type ultramafic rocks emplaced into the crust by the faulting as mantle slab types. With the petrographical characteristics, these mineralogical compositions suggest that the ultramafic rocks of the Bibong area have experienced several stages of retrogressive metamorphism in a condition ranging from the upper amphibolite facies to greenschist facies.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.11a
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• Korean Journal of Materials Research
• /
• v.20 no.7
• /
• pp.356-363
• /
• 2010

For this paper, we investigated the area specific resistance (ASR) of commercially available ferritic stainless steels with different chemical compositions for use as solid oxide fuel cells (SOFC) interconnect. After 430h of oxidation, the STS446M alloy demonstrated excellent oxidation resistance and low ASR, of approximately 40 $m{\Omega}cm^2$, of the thermally grown oxide scale, compared to those of other stainless steels. The reason for the low ASR is that the contact resistance between the Pt paste and the oxide scale is reduced due to the plate-like shape of the $Cr_2O_3$(s). However, the acceptable ASR level is considered to be below 100 $m{\Omega}cm^2$ after 40,000 h of use. To further improve the electrical conductivity of the thermally grown oxide on stainless steels, the Co layer was deposited on the stainless steel by means of an electroless deposition method; it was then thermally oxidized to obtain the $Co_3O_4$ layer, which is a highly conductive layer. With the increase of the Co coating thickness, the ASR value decreased. For Co deposited STS444 with 2 ${\mu}m$hickness, the measured ASR at $800^{\circ}$ after 300 h oxidation is around 10 $m{\Omega}cm^2$, which is lower than that of the STS446M, which alloy has a lower ASR value than that of the non-coated STS. The reason for this improved high temperature conductivity seems to be that the Mn is efficiently diffused into the coating layer, which diffusion formed the highly conductive (Mn,Co)$_3O_4$ spinel phases and the thickness of the $Cr_2O_3$(S), which is the rate controlling layer of the electrical conductivity in the SOFC environment and is very thin

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.5
• /
• pp.255-264
• /
• 2013

Cobalt aluminate ($CoAl_2O_4$) is a highly stable pigment with excellent resistance to light, weather, etc., which has resulted in widespread use as a ceramic pigment. Due to the unique optical characteristics, $CoAl_2O_4$ is generally used as a coloring agent to decorate porcelain products, glass, paints and plastics. Here, $CoAl_2O_4$ pigments were synthesized by polymerized complex method and solid state reaction. Then $CoAl_2O_4$ pigment were grinded using the attrition milling with 1 mm size zirconia ball for 3 hours. The attrition milling process was performed at the constant speed of 800 rpm and ball to powder weight ratio (BPR) was 100 : 1. The characteristics of synthesized pigment were analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), particle size analyser (PSA) and CIE $L^*a^*b^*$. The XRD patterns of $CoAl_2O_4$ show single phase spinel structure. The particle size of $CoAl_2O_4$ measured by FE-SEM, TEM and PSA analysis was in the range of 100~200 nm. The blue color of obtained $CoAl_2O_4$ pigments could be confirmed through CIE $L^*a^*b^*$ measurement.

• Journal of the Korean Magnetics Society
• /
• v.10 no.3
• /
• pp.106-111
• /
• 2000

The magnetic thin films can be prepared without vacuum process and under the low temperature (<100 $^{\circ}C$) by ferrite plating. We have performed ferrite plating of M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$(x=0.00~0.08) films and N $i_{x}$Z $n_{0.22}$F $e_{*}$2.78-x/ $O_4$(x=0.00~0.15) films on cover glass at the substrate temperature 90 $^{\circ}C$. The crystal structure of the samples has been identified as a single phase of polycrystal spinel structure by x-ray diffraction technique. The lattice constant in the M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$films increases but in the N $i_{x}$Z $n_{0.22}$F $e_{*}$2.78-x/ $O_4$films decrease with the composition parameter, x. The saturation magnetization in the M $n_{x}$Z $n_{0.22}$F $e_{2.78-x}$ $O_4$films does not greatly change, in agreement with observations on bulk samples.k samples.k samples.

• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.523-527
• /
• 2002

LiMn$_2$O$_4$ compounds were synthesized by calcining a mixture of LiOH and MnO$_2$(CMD) at 47$0^{\circ}C$ for 10 h and then calcining again at $650^{\circ}C$ to 90$0^{\circ}C$ fur 48 h in air with intermediate grinding. All the synthesized samples exhibited XRD patterns for the cubic spinel phase with a space group Fd3m. The lattice parameter increased gradually as the sintering temperature rose. The electrochemical cells were charged and discharged fur 20 cycles at a current density 300$\mu$A/$\textrm{cm}^2$ between 3.5 V and 4.3 V. The voltage vs. discharge capacity curves for all the samples showed two plateaus. The LiMn$_2$O$_4$ sample calcined at 90$0^{\circ}C$ had the largest first discharge capacity. This sample exhibited the best crystallinity, had relatively large lattice parameter and had relatively large particles with rectatively homogeneous size. All the samples showed good cycling performances. Among all the samples, the LiMn$_2$O$_4$ calcined at 85$0^{\circ}C$ had relatively large first discharge capacity and very good cycling performance. The addition of excess LiOH and the mixing in ethanol considered to help the formation of the more LiMn$_2$O$_4$ phase per unit weight sample and the more stable LiMn$_2$O$_4$phase. These led to the larger discharge capacities and the better cycling performances. The cyclic voltammograms fur the second cycle of the LiMn$_2$O$_4$ samples showed the oxidation and reduction peaks around 4.05 V and 4.18 V and around 4.08 V and 3.94 V, respectively. The larger first discharge capacity of the sample calcined at the higher temperature is related to the larger lattice parameter.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2006

Lithium titanium oxide $(Li_4Ti_5O_{12})$ with spinel-framework structures as anode material for lithium-ion battery was prepared by sol-gel and high energy ball milling (HEBH) method. According to the X-ray diffraction (XRD), Particle Size Analyses(PSA) and scanning electron microscopy (SEM) analysis, uniformly distributed $Li_4Ti_5O_{12}$ particles with grain sizes of 100 nm were observed. Half cells, consisting of $Li_4Ti_5O_{12}$ as working electrode and lithium foil as both counter and reference electrodes showed the high performance of high rate discharge capacity and 173 mAh/g at 0.2C in the range of $1.0\sim2.5 V$. Furthermore, the crystalline structure of $Li_4Ti_5O_{12}$ didn't transform during the lithium intercalation and deintercalation process.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.1
• /
• pp.81-87
• /
• 2009

An indium-tin oxide (ITO) coated spinel manganese oxide (${LiMn_2}{O_4}$, LMO) is prepared and its high-temperature ($55^{\circ}C$) cycle performance and rate capability are examined. A severe electrolyte decomposition and film deposition is observed on the un-coated ${LiMn_2}{O_4}$ cathode, which leads to a significant electrode polarization and capacity fading. Such an electrode polarization is, however, greatly reduced for the ITO-coated (> 2 mol%) LMO cathode, which leads to an improved cycle performance. This can be rationalized by a suppression of electrolyte decomposition, which is in turn indebted to a decrease in the direct contact area between LMO and electrolyte. The suppression of film deposition on the ITO-coated LMO cathode is confirmed by infra-red spectroscopy. The rate capability is also improved by the surface coating, which may be resulted from a suppression of resistive film deposition and high electric conductivity of ITO itself.