• Korean Chemical Engineering Research
• /
• v.54 no.3
• /
• pp.387-393
• /
• 2016

Fluorinated polyurethane coating solutions were synthesized from perfluoroalkyl alcohol, toluene diisocyanate, and polycarbonate diol as starting materials. Next, coating films were prepared by spin-coating the fluorinated polyurethane coating solutions on the PC substrates, followed by thermal curing at $120^{\circ}C$. The obtained fluorinated polyurethane coating films were characterized by FT-IR spectroscopy, UV-Vis spectrometer, contact angle tester and pencil hardness tester. Contact angle measurements of water on the coating films showed that the addition of perfluoroalkyl alcohol improved the water repellency and increased the contact angle from $81^{\circ}C$ to $111^{\circ}C$. However, the pencil hardness of coating films exhibited a constant grade of H, irrespective of the addition of perfluoroalkyl alcohol.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1092-1098
• /
• 2006

The influence of the concentration of precursor solution and the number of solution coatings on the densification of the $Pb(Zr_xTi_{1-x})O_3$ (PZT) thick films was studied. PZT powder and PZT precursor solution were prepared by3 sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The composition of powder and precursor solution were PZT(70/30) and PZT(30/70), respectively. The PZT precursor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 to 2.0 mol/L[M] and the number of coating was repeated from 0 to 6. The XRD patterns of all PZT thick films shelved typical perovskite polycrystalline structure. The porosity of the thick films was decreased with increasing the number of coatings and 6-time coated films with 1.5 M showed the dense microstructure and thickness of about $60{\mu}m$. The relative dielectric constant of the PZT thick film was increased with increasing the number of solution coatings and the thick films with 1.5 M, 6-time coated showed the 698. The remanent polarization the 1.5 M and 6-time coated PZT thick films was $38.3{\mu}C/cm^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.146-146
• /
• 2011

The blue light emitting diode (LED) structure based on non-polar a-plane (11-20) GaN which was coated TiO2 nanoparticles using spin coating method was grown on r-plane (1-102) sapphire substrates to improve light extraction efficiency. We report on the emission and structural properties with temperature dependence of photoluminescence (PL) and x-ray rocking curves (XRC). From PL results at 13 K of undoped GaN samples, basal plane stacking fault (BSF) and near band edge (NBE) emission peak were observed at 3.434 eV and 3.484 eV, respectively. We also found the temperature-induced band-gap shrinkage, which was fitted well with empirical Varshini's equation. The PL intensity of TiO2 nanoparticles ?coated multiple quantum well (MQW) sample is decayed slower than that of no coating sample with increasing temperature. The anisotrophic strain and azimuth angle dependence in the films were shown from XRC results. The full width at half maximum (FWHM) along the GaN [11-20] and [1-100] directions were 564.9 arcsec and 490.8 arcsec, respectively. A small deviation of FWHM values at in-plane direction is attributed to uniform in-plane strain.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.469-469
• /
• 2011

고효율 염료감응형 태양전지(DSSC, Dye-Sensitized Solar Cell)의 구현을 위해서 유용한 방법중 하나는 정렬된 기공 (pore)을 $TiO_2$막 내에 형성시키는 것이다. 메조포러스 (mesoporous) $TiO_2$막은 dip coating이나 spin coating과 같은 방법으로 주로 증착되고 있으며, P123이나 F127과 같은 amphiphilic triblock copolymer를 메조포러스 구조를 만들기 위한 뼈대로 사용하고 있다. 또한, 이렇게 생성된 구조에서 amphiphilic triblock copolymer는 열처리 공정을 통하여 쉽게 제거될 수 있다. 고효율 태양전지를 구현하는 또 다른 방법으로는 패턴 된 기판을 사용하는 것이다. 패턴 된 기판은 빛의 반사를 억제하여 흡수율을 높이는 역할을 한다. 그러나 패턴 된 기판 위에서 메조포러스 $TiO_2$막의 형성에 관한 연구는 부족한 실정이다. 본 연구에서는 spin coating 방법으로 패턴 된 Si (111) 기판 위에 메조포러스 $TiO_2$를 성장하고 그 미세구조를 분석하였다. 패턴 된 기판은 nanosphere lithography(NSL) 법으로 mask를 증착한 후 건식 식각 (dry etching) 공정을 통해서 제작되었으며, 마스크와 불순물 등 은 초음파 세척 등으로 제거되었다. 메조포러스 $TiO_2$막은 1-propanol, P123, titanium isopropoxide와 HCl을 섞어 만든 용액으로 1 cm${\times}$1 cm 기판 위에 3000 rpm과 4000 rpm으로 각각 증착하였으며, 5일 동안 4도에서 에이징한 후 350도에서 3시간 열처리하였다. 이렇게 형성한 메조포러스 막의 형상과 미세구조적 특성이 주사전자현미경(SEM, scanning electron microscope), X-선 회절(XRD, X-ray diffraction) 등을 이용하여 연구되었다. 특히, 증착 조건에 따른 메조포러스 $TiO_2$박막의 형성 기구에 관한 고찰이 진행되었다. 나아가, $TiO_2$박막과 패턴 사이에 형성되는 계면 구조에 관한 연구를 투과전자현미경을 이용하여 진행하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.2
• /
• pp.38-42
• /
• 2016

We investigate the solution coating process of organic small molecules that are easily recrystallized in a solvent. The spin-coated films of small molecule N,N'-diphenly-N,N'-bis(1,1'-biphenyl)-4,4'-diamine (NPB) exhibit many aggregations on the surface and thus poor surface morphology. To tackle it, we have added a chain-entangled polymer poly(N-vinylcarbazole) (PVK) into the NPB solution. It is found that a small amount of PVK indeed prohibits the recrystallization of NPB in a solvent. By the addition of PVK (30 wt%), the peak-to-peak roughness of the films is reduced from 262 nm down to 2.7 nm, which is even lower than that (~5.1 nm) of the polymer film. It is also demonstrated that OLED with the PVK-mixed NPB film shows higher current and power efficiencies, compared to OLED with the NPB or PVK film. It is attributed that the addition of PVK into NPB suppresses the occurrence of leaky channels induced by the recrystallization phenomenon.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.3
• /
• pp.51-55
• /
• 2015

We have fabricated silver nanowire (AgNW) films as a stretchable and transparent electrode on polydimethylsiloxane (PDMS) substrates using a spray coater. Inherently, they show poor surface roughness and stretchability. To tackle it, we have employed a conductive polymer, poly (3,4-ethylenedioxythiophene) : Poly(styrene sulfonate) (PEDOT : PSS). PEDTO : PSS solution is mixed with AgNWs or spin-coated on the AgNW film. Compared with AgNW film only, PEDOT : PSS film only, and polymer-mixed AgNW films, the AgNW/polymer bilayer films exhibit much better surface roughness and stretchability. It is found that spray-coating of AgNWs on uncured PDMS and spin-coating of PEDOT : PSS solution on the AgNW films enhance the surface roughness of electrodes. Such a bilayer structure also provides a stable resistance under tensile strain due to the fact that each layer acts as a detour route for carriers. With this structure, we have obtained the peak-to-peak roughness ($R_{pv}$) as low as 76.8nm and a moderate increase of sheet resistance (from $10{\Omega}/{\Box}$ under 0% strain to $30{\Omega}/{\Box}$ under 40% strain).

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.389-398
• /
• 2000

Transparent, abrasion resistant coatings with 4~13 ${\mu}{\textrm}{m}$ thickness were prepared by spin-coating on polycarbonates with organic/inorganic hybrid solutions, followed by UV curing and heat treatment at 12$0^{\circ}C$ for 12 hours. The coating solutions were composed of inorganic phase and organic phase in 0:100, 20:80, 30:70, 50:50, 80:20 wt% ratios, respectively, mixed with photoinitiator, senaitizer and surfactant. The inorganic phase was formed by sol-gel reaction of TEOS and silane coupling agent MPTMS in 1 : 2 or 2 : 1 molar ratios, the organic phase consisted of difunctional urethane acrylate oligomeric resin, multifunctional acrylate TMPTA and HDDA in 4 : 3 : 3 wt% ratio. The coating systems were investigated by FT-IR, $^{29}$ Si-NMR spectra. In addition, TGA/DSC for thermal analysis and SEM, AFM observation for coated surface were examined. Gererally, the homogeneity of phases, the surface smoothness of coating and abrasion resistance were improved with the higher content of inorganic component. Namely, coating system with below 10 $\AA$ surface roughness and T$_{g}$ of 15$0^{\circ}C$ showed only 10% decrease in light transmittance after abrasion test, whereas uncoated polycarbonate substrate exhibited 46% decrease..

• Korean Chemical Engineering Research
• /
• v.56 no.3
• /
• pp.327-334
• /
• 2018

Water-repellent coating solutions were prepared by sol-gel method using tetraethoxysilane (TEOS) and methyltrimethoxysilane (MTMS) as precursors. The solutions were spin-coated on a cold-rolled steel sheet and thermally cured to prepare a non-fluorine water-repellent coating films. The effects of molar ratios of MTMS/TEOS, water concentration and ammonia concentration on the hydrophobic properties of the coating films were studied. The contact angle of water on coating films prepared by varying the molar ratio of MTMS/TEOS to 1~20 showed a maximum value of $108^{\circ}$ when the MTMS/TEOS molar ratio was 10. With increasing water content, the coating films showed the larger contact angles and the better the water repellency. As the amount of ammonia added was increased, the contact angles of coating films were increased, showing the better the water repellency. It is considered that the larger the amount of ammonia added, the larger the size of the silica particles generated, which increases the surface roughness of the silica particles, thereby increasing the water repellency.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.112-117
• /
• 2008

Organic-inorganic hybrid solutions were prepared via sol-gel method using glycidoxypropyl trimethoxysilane (GPTMS) and methyl triethoxysilane (MTES) as starting precursors at a molar ratio of 1:1. The photochromic coating solutions were prepared by mixing the solutions of photochromic dye (spiropyran) dissolved in ethylacetate (EA) with the organic-inorganic hybrid solutions. Photochromic films were prepared on polycarbonate substrate by spin coating and cured for 2 h at $100^{\circ}C$. The resulting films exhibited a reversible color change upon irradiation with UV light. The photochromic properties of the films showed that the color-fading speed increases with increasing the EA content in the coating solutions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.665-668
• /
• 1999

Thin films of Pb(Zr,Ti)O$_3$ were fabricated by means of the sol-gel spin-coating method and the multi-coating of eight coating numbers. The thin films were dried on the temperature range of 250 ~ 400($^{\circ}C$), whenever the specimens were dried after each coating Processing. The fabricated ferroelectric thin films of lead zirconate titanate(PZT) were treated with the rapid thermal annealing(RTA) at 650($^{\circ}C$),or 3(min), and direct insertion thermal annealing(DITA) at 650($^{\circ}C$), for 30(min). The measured properties of dielectric thin films were following: The good results of dielectric properties were shown by the RTA specimen. The saturation polarization(Ps), remanent polarization(Pr), coercive field (Ec), dielectric constant and dielectric loss factor of the RTA specimen were estimated to be about 27.1[ $\mu$ C/$\textrm{cm}^2$], 13.7[ $\mu$ C/$\textrm{cm}^2$], 55.6(kV/cm), 786 and 6.4(%) respectively.