• 농업과학연구
• /
• 제50권3호
• /
• pp.457-468
• /
• 2023

The purpose of this study is to develop a high-speed combine harvester. The performance was evaluated by composing a dynamic simulation model of a threshing cylinder and analyzing the amount of threshed rice grain during threshing operations. The rotational speed of the threshing cylinder was set at 10 rpm intervals from 500 rpm until 540 rpm, based on the rated rotational speed of 507 rpm. The rice stem model was developed using the EDEM software using measured rice stem properties. Multibody dynamics software was utilized to model the threshing cylinder and tank comprising five sections below the threshing cylinder, and the threshing performance was evaluated by weighing the grain collected in the threshing tank during threshing simulations. The simulation results showed that section 1 and 2 threshed more grains compared to section 3 and 4. It was also found that when the threshing speed was higher, the larger number of grains were threshed. Only simulation was conducted in this study. Therefore, the validation of the simulation model is required. A comparative analysis to validate the simulation model by field experiment will be conducted in the future.

• Journal of Biosystems Engineering
• /
• 제27권2호
• /
• pp.89-96
• /
• 2002

The trend of consumption of vegetable soybeans is increasing because they are recognized as the clean vegetable. The works requiring the most intensive labor are threshing and seperation ones, and they form about 80% of total labour for vegetable soybeans production. It is necessary to develop the vegetable soybeans-thresher for the sake of cost down of vegetable soybeans production. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which control the speed of threshing cylinder and the teeth gap and investigate the detachment forces. The result are as follows ; The ratio of un-threshed soybeans-pod to stem after threshing work is decreasing as the threshing cylinder speed increases: 0.0% and 2.8% at 55m/s and 18m/s of threshing cylinder speed respectively. Also the ratio of un-threshed soybeans-pod to stem is shown as 2.0% below in the condition of 64~160mm of teeth gap and over 28m/s of threshing cylinder speed. The damaged pod ratio of detached soybeans after threshing work is decreasing as the threshing cylinder speed increases: 4.8% and 1.3% at 55m/s and 18m/s of threshing cylinder speed respectively. The minimum damaged pod ratio of detached soybeans are shown as 1.0%, 1.5% and 1.9% at 18m/s, 28m/s and 37m/s of threshing cylinder speed respectively. The average detachment forces of pods are shown as 1.5kg$_{f}$ for 3 grains, 1.2kg$_{f}$ for 2 grains and 0.8kg$_{f}$ for 1 grain respectively. The maximum detachment force of pod is shown as 2.7kg$_{f}$ for 3 grains. grains.

• Journal of Biosystems Engineering
• /
• 제35권6호
• /
• pp.380-386
• /
• 2010

This study was carried out to develop soybean thresher which is able to reduce the soybean threshing damage in comparison to the conventional thresher. A threshing cylinder with different diameter of 480 and 384 mm at each end and with one quarter disc pegs of 60 mm radius was developed and attached to the prototype thresher. A conventional thresher which has a threshing cylinder with $\wedge$ type threshing pegs and same diameter of 480 mm at each end was used for comparative test. A series of comparative performance test was conducted using sun-yu and chung-ja soybean. For sun-yu bean, which is white and usually used for soybean paste and soy sauce, the ratio of damaged beans of prototype ranged 2-3% for 330-360 rpm which is recommended cylinder speed by manufacturer. The ratio of damaged beans of conventional thresher was 3-4% for the same range of cylinder speed. chung-ja beans with black color usually shows high damaged ratio compared with white beans, thus cylinder speed of 250-300 rpm is recommended by manufacturer to reduce the damaged ratio. For this range of cylinder speed, the damaged ratio of prototype was 1.3-1.4% and it was 2.7-6.1% for the conventional thresher. Thus prototype is able to reduce the damaged ratio 1.5-5.0% compared with conventional thresher. Prototype shows 0.4% of unthreshed soybean ratio for sun-yu bean in the optimum range of cylinder speed and it was 0.87% for the conventional thresher. For chung-ja bean, the ratio of unthreshed soybean was almost same for both prototype and conventional thresher with the value of 4.0%. The reason of high unthreshed soybean ratio for chung-ja bean compared sun-yu bean is due to the high seed moisture content of 29.11% which is much higher than that of the recommended.

• Journal of Biosystems Engineering
• /
• 제10권2호
• /
• pp.36-46
• /
• 1985

This study was intended to develop the mathematical model of the head-fed type threshing unit. As the first step, the physical model of the threshing phenomena was considered to consist of four separate processes as 1) detachment process of grains, 2) movement of grains between the cylinder and concave, 3) grain penetration through stems of bundle, and 4) grain passing through concave. The mathematical and computer models were developed based on the physical models. Threshing experiments were performed and determined the distribution of grain accumulation along the cylinder shaft by varying the moisture content of grains, feeding rate, and cylinder speed. It was found that the model developed coincided very well with the experimental results for the varied operational conditions. Greater concentration of grains passing through concave toward the thresher inlet was equally true for the model and experiment work for the threshing of grains with higher moisture content and with higher cylinder-speed. The model could be used for obtaining the optimized design or for optimizing the performance of the head-fed type threshing unit if term as to power requirement for threshing may be additionally included in the developed model.

• Journal of Biosystems Engineering
• /
• 제40권2호
• /
• pp.110-114
• /
• 2015

Purpose: A threshing machine for shatter-resistant sesame was designed and developed in this study. Methods: Two types of sesame (shatter-resistant and conventional) were tested using the developed sesame threshing system. Three types of serrated bars were designed and evaluated through performance tests, in terms of the ratio of unthreshed sesame. Results: In the case of conventional sesame, the ratio of unthreshed sesame did not show any difference with bar type or cylinder rotation speed. For shatter-resistant sesame, however, the ratio of unthreshed sesame decreased with increased cylinder rotating speed for all three types of bar. Conclusions: These results are useful for the construction and utilization of an efficient threshing harvester. The type-L bar showed the best result in the energy equation.

• Journal of Biosystems Engineering
• /
• 제29권5호
• /
• pp.433-440
• /
• 2004

Worldwide consumption of vegetable soybean has been increasing recently, but in the process of vegetable soybean production, threshing and separation work accounts fur about $80\%$ of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The main objective of this study is to acquire the basic in-formations for design of the vegetable soybean thresher which is suitable for domestic circumstances. We made the experimental system to investigate the threshing and separating performance at the several speeds of threshing cylinder and separating blower according to the kinds of threshing tooth. The result are as follows; Threshing performance of vegetable soybean thresher was shown as the best in case the threshing tooth made of rubber which has the 80 of Shore hardness was used at the circumference speed of cylinder of 5.8$\~$8.1m/s. Also separating cleaning performance of vegetable soybean thresher was shown as the best at more than 1,300 rpm of blower speed and $60\~80\%$ of opening ratio of suction port.

• Journal of Biosystems Engineering
• /
• 제5권1호
• /
• pp.1-14
• /
• 1980

Threshing operation may be one of the most important processes in the paddy post-production system as far as the grain loss and labor requirement are concerned . head-feeding type threshers commercially available now in Korea originally were developed for threshing dry paddy in the range of 15 to 17 % in wet basis. However, threshing wet-paddy with the grain moisture content above 20 % has been strongly recommended, especially for new high-yielding Indica -type varieties ; (1) to reduce high grain loss incurred due to the handling operations, and (2) to prevent the quantitative and qualitative loss of milled -rice when unthreshed grains are rewetted due to the rainfall. The objective of this study were to investigate the adaptability of both a head-feeding type thresher and a throw-in type thresher to wet-paddy , and to find out the possiblilities of improving the components of these threshers threshing. Four varieties, Suweon 264 and Milyang 24 as Tongil sister line varieties, minehikari and Jinhueng as Japonica-type varieties, were used at the different levels of the moisture content of grains. Both the feed rate and the cylinder speed were varied for each material and each machine. The thresher output quality , composition of tailing return, and separating loss were analyzed from the sampels taken at each treatment. A separate experiment for measurement opf the power requirement of the head-feeding type thresher was also performed. The results are summarized as follows : 1. There was a difference in the thresher output quality between rice varieties. In case of wet-paddy threshing at 550 rpm , grains with branchlet and torn heads for the Suweon 264 were 12 % and 7 % of the total output in weight, respectively, and for the Minehikari 4.5 % and 2 % respectively. In case of dry paddy threshing , those for the Suweon 264 were 8 % and 5% , and for the Minehikari 4% and 1% respectively. However, those for the Milyang 23 , which is highly susceptable to shattering, were much lower with 1 % and 0.5% respectively, regardless of the moisture content of the paddy. Therefore, it is desirable to breed rice varieties of the same physical properties as well as to improve a thresher adaptable to all the varieties. Torn heads, which increased with the moisture content of rall the varieties except the Milyang 23 , decreased as the cylinder speed increased, but grains with branchlet didnt decrease. The damaged kernels increased with the cylinder speed. 3. The thresher output quality was not affected much by the feed rate. But grains with branchlet and torn heads increased slightly with the feed rate for the head-feeding type thresher since higher resistance lowered at the cylinder speed. 4. In order to reduce grains with branchlet and torn heads in wet-paddy threshing , it is desirable to improve the head-feeding type thresher by developing a new type of cylinder which to not give excess impact on kernels or a concave which has differenct sizes of holes at different locations along the cylinder. 5. For the head-feeding type thresher, there was a difference in separating loss between the varieties. At the cylinder speed of 600 rpm the separating losses for the Minehikari and the Suweon 264 were 1.2% and 0.6% respectively. The separating loss of the head-feeding type thresher was not affected by the moisture content of paddy while that of the Mini-aged thresher increased with the moisture content. 6. From the analysis of the tailings return , to appeared that the tailings return mechanism didn't function properly because lots of single grains and rubbishes were unnecessarily returned. 7. Adding a vibrating sieve to the head-feeding type thresher could increase the efficiency of separation. Consequently , the tailing return mechanism would function properly since unnecessary return could be educed greatly. 8. The power required for the head-feeding type thresher was not affected by the moisture content of paddy, but the average power increased linearly with the feed rate. The power also increased with the cylinder speed.

• Current Research on Agriculture and Life Sciences
• /
• 제21권
• /
• pp.23-29
• /
• 2003

Worldwide consumption of vegetable soybean bas been increasing recently, hence it is necessary to produce good quality of soybean in our farms. In the process of vegetable soybean production threshing and seperation work accounts for about 80% of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which measure the physical properties and investigate the detachment forces. Also, We calculated the minimum speed of threshing cylinder. The result are as follows; 1. The average length of soybean stem is 68.2cm. 2. The length of soybean pods are seen as 61.3mm for 3 grain, 52.6mm fer 2 grains and 41.0mm fer 1 grain 3. The widths of soybean pods are seen as 14.1mm fer 3 grain, 13.8mm fer 2 grains and 13.4mm fer 1 grain. 4. The weights of soybean pods are seen as 4.1grams for 3 grains, 2.7grams for 2 grains and 1.4grams for 1 grain. 5. The average detachment forces of pods are seen as 1.5kgf for 3 grains, 1.2kgf for 2 grains and 0.8kgf for 1 grain respectively For 1 grain, the detachment force of pods ranges from 0.2kgf to 1.4kgf. For 2 grains, the minimum detachment force of pods is seen as 0.6kgf and the maximum one is seen as 2.5kgf. For 3 grains, the minimum detachment force of pods is seen as 0.7kgf and the maximum one is seen as 2.7kgf. 6. The minimum speed of threshing cylinder is shown 6.83m/s.

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.124-132
• /
• 1991

This study was carried out to obtain the information needed in the development of forward speed control system and the improvement of combine performance. The effects of variety, grain moisture content and forward speed on the combine load characteristics were investigated through experiments. The results of this study are summarized as follows. 1. A data acquisition system was developed to measure the engine speed and the torques and speeds of the threshing cylinder, dean-grain auger and tailings-return auger. The system consisted of transducers, signal conditioner, interface board and microcomputer. The system accuracy is better than ${\pm}2.3%$ full scale. 2. Linear regression equations were obtained for the torque, speed and power requirement of threshing cylinder for different paddy varieties, grain moisture contents and feed rates. 3. The maximum value of relative frequency for threshing cylinder torque decreased as the increase in feed rate and moisture content. The range of torque fluctuation was 1.2~3.7 and 1.2~1.9 times the average and maximum torque, respectively. The maximum value of power spectrum density (PSD) appeared to be about 11 Hz regardless of paddy variety, grain moisture content and feed rate. 4. The speed of tailings return thrower decreased rapidly at below 900rpm, and it fell to near zero about 3 seconds after that time. When the travelling of combine harvester was stopped immediately after sensing the overload, it took about 7 seconds for a full recovery of the no-load speed of tailings return thrower.

• Journal of Biosystems Engineering
• /
• 제15권2호
• /
• pp.110-122
• /
• 1990

This study was undertaken to develop the feed rate control system for the head feed thresher by making use of the microprocessor and to evaluate the response of the system to a various threshing conditions. The control unit was composed of one-board microcomputer. The speed of the wet-paddy feeding chain was controlled by dc moter with PI controller. It was used the adaptive control method to maintain the constant feed rate regardless of the fed rice varieties. The sliding type potentiometer was used as the feed rate sensor, which was attached on the sheaf-holding apparatus. The mathematical models of the system components were derived and computer simulation was developed for investigating the parameters affecting on control performance and for estimating the response of the system. A one-board microcomputer-based feed rate control system developed in this study was properly functioned and assessed as adequate for the feed rate control system of the head feed thresher. Based on the simulation for the bundle feed, it was anticipated that the lower setting value of the cylinder speed(RL) is to be set higher than the limiting operational speed. In addition, the higher setting value of the cylinder speed(RH) is to be set lower than the limiting cylinder speed for threshing. The computer simulation for the continuous spread feed showed that the lower the setting value of straw layer thickness(LL) was set, the shorter the correction time. However, if too low LL may be established, the feed rate could not reach to its desired rate.