• 한국태양에너지학회 논문집
• /
• 제32권3호
• /
• pp.146-152
• /
• 2012

To install a wind power generator, the survey on the wind environment resources must be conducted in advance. The survey on the wind environment resources is to collect and analyze data regarding the wind speed and direction on a data logger. The data logger consists of a sensor, signal processing circuit and storage device. According to the analysis of the stored data, the amount of power generation by the types of generators can be predicted and the most optimal generator including safety grade can be selected, and in case of installing a generator in the future, it can be utilized as basic data regarding supporting base and foundation construction method of survey points. Data logger was developed for a small wind power generator that is suitable for the international standard(IEC 61400) by using DSP-F28335 micro controller in this paper. It was developed to measure the wind speed of 1 [m/s]~17 [m/s], the wind direction of 0 [$^{\circ}$]~359 [$^{\circ}$], and temperature of -30 [$^{\circ}C$]~50 [$^{\circ}C$], and the comparative experiment with other companies' data loggers was conducted, and an error was measured to be less than ${\pm}0.1$ [m/s] for wind speed and less than +1 [$^{\circ}$] for wind direction.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1352-1355
• /
• 1997

This paper presents the algorithm for estimating the attitude of an underwater vehicle using EFK. The system model is designed by linerizing the nonlinear Euler angle differential equation and the measurements is a speed logger output. The simulation result shows that the estimation lagorithm is adequate for decreasing attitude errors that grow abruptly during the motion with acceleration and rotation. It also shows that we can adapt the algorithm for compensating initial attitude errors generated after initial leveling.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권2호
• /
• pp.166-171
• /
• 2015

Recently, the international standard RS-422 serial communication, which was primarily designed for the communications between micro-controllers, has been used as a communication method on the ship. However, as the NMEA (National Marine Electronics Association) 2000 standardization progresses recently, a high-speed Ethernet-based communication environment is expected to be an alternative communication method instead of the RS-422 gradually. In addition, the ship's main instrumentation equipment with versatility and convenience is implemented to control devices as monitoring and controlling tools. This paper describes an implementation of wireless ultrasonic anemometer and anemoscope data processing and logger system using PC network, where the control processing equipment such as a separate operational console, data-logger, and indicator is required for the system. For these, the related element technologies to implement ultrasonic anemometer and anemoscope data processing system are expressed as a functional modules, and the NMEA 2000 standard certified data-logger system is implemented without the separate operational console.

• Wind and Structures
• /
• 제14권4호
• /
• pp.337-357
• /
• 2011

The collection of wind speed time series by means of digital data loggers occurs in many domains, including civil engineering, environmental sciences and wind turbine technology. Since averaging intervals are often significantly larger than typical system time scales, the information lost has to be recovered in order to reconstruct the true dynamics of the system. In the present work we present a simple algorithm capable of generating a real-time wind speed time series from data logger records containing the average, maximum, and minimum values of the wind speed in a fixed interval, as well as the standard deviation. The signal is generated from a generalized random Fourier series. The spectrum can be matched to any desired theoretical or measured frequency distribution. Extreme values are specified through a postprocessing step based on the concept of constrained simulation. Applications of the algorithm to 10-min wind speed records logged at a test site at 60 m height above the ground show that the recorded 10-min values can be reproduced by the simulated time series to a high degree of accuracy.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.819-826
• /
• 2000

This study was performed to develop a measurement system of tractor field performance for plow and rotary operations. Measurement system for tractor consisted of torque sensors to measure torque of drive axles and PTO axle, speed sensors to measure rotational speed of drive axles and engine, microcomputer to control data logger, and data logger as I/O interface system. The measurement system was installed on four-wheel-drive tractor. Four-element full-bridge type strain gages were used for torque measurement of drive axles and optical encoders were used to measure speeds of drive axles and engine. Slip rings were mounted on the rotational axles. Signals from sensors were inputted to data logger that was controlled by microcomputer with parallel communication. Sensors were calibrated before the field tests. Regression equations were found on completion of the calibrations. The field experiment was performed at paddy fields and uplands. Rotary and plow were used when the tractor was operated in the field. Travelling speeds of the tractor were 1.9 km/h, 2.7 km/h, 3.7 km/h, 5.5 km/h, 8.2 km/h, and 11.8 km/h. Operating depths of implements were maintained approximately 20cm during the tests. Torque data of drive axles were different at each location during plow and rotary operations. Results showed that torque of rear axles were greater than those of front axles. Total torque were 6860 - 11064 Nm at the upland and 7360 - 14190 Nm at the paddy field for plow operations. It was found that torque at the paddy field were about 20% greater than those at the upland for plow operations. Torque data showed that rotary operations required less power than plow operation at the paddy field and the upland. Torque measurements at each axle for rotary operations were only 8 - 16% of plow operations in the upland and 15 - 20% in the paddy field.

• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.375-383
• /
• 2011

This paper describes a real-time hardware simulator for a grid-tied Permanent Magnet Synchronous Generator (PMSG) wind power system, which consists of an anemometer, a data logger, a motor-generator set with vector drive, and a back-to-back power converter with a digital signal processor (DSP) controller. The anemometer measures real wind speed, and the data is sent to the data logger to calculate the turbine torque. The calculated torque is sent to the vector drive for the induction motor after it is scaled down to the rated simulator power. The motor generates the mechanical power for the PMSG, and the generated electrical power is connected to the grid through a back-to-back converter. The generator-side converter in a back-to-back converter operates in current control mode to track the maximum power point at the given wind speed. The grid-side converter operates to control the direct current link voltage and to correct the power factor. The developed simulator can be used to analyze various mechanical and electrical characteristics of a grid-tied PMSG wind power system. It can also be utilized to educate students or engineers on the operation of grid-tied PMSG wind power system.

• 한국통신학회논문지
• /
• 제39C권2호
• /
• pp.184-190
• /
• 2014

선박 통신은 1993년 ISO에서 국제 표준 규격인 RS-422통신을 이용하며, 마이크로컨트롤러들 간의 통신을 위해 설계된 시리얼 네트워크 통신 방식을 사용하였으나, 최근 NMEA2000 표준화가 진행됨에 따라 점차 빠르게 Ethernet 기반 통신 환경으로 대체 되어질 전망이다. 선박에서 사용되어지고 있는 주요 계측 장비들은 점차 범용성과 편의성을 가지는 최신 장치들을 이용해 이를 관리하게 되어짐에 따라 선박 내 다양한 곳에서 이를 활용하여 제어 및 관리 시스템들이 구현되어지고 있는 실정이다. 풍향 풍속계는 선박의 마스트 끝이나 풍력 단지 가장 높은 곳에 일반적으로 설치되어 풍향과 풍속을 계측하는 장비로써, 국제해사기구(IMO : International Maritime Organization)의 규정에 따라 필수 장비로 선박에 탑재되고 있는 장비이다. 본 논문에서는 초음파 풍향 풍속 시스템을 처리하기 위해 기존에는 별도 제어 콘솔, 데이터 로거(data-logger), 인디케이터(Indicator) 등의 제어 처리를 위한 기반 장비들이 필요하였던 시스템을 사용자 환경에 따른 PC NETWORK를 이용하여 풍향 풍속 자료 처리시스템을 구현하였다. 또한, 초음파 풍향 풍속 자료 처리 시스템을 구현하기 위한 요소 기술을 기능별 함수로 나타내었으며, NMEA 2000 표준 인증에서도 별도의 운용 콘솔 없이 풍향 풍속 자료의 처리를 위한 자료 처리 운용시스템의 기능들을 구현하고자 하였다.

• 수산해양기술연구
• /
• 제55권1호
• /
• pp.29-38
• /
• 2019

In order to investigate the behavioral characteristics of Pacific cod (Gadus macrocephalus) released at the entrance of Jinhae Bay, Korea, the direction and range of movement, swimming speed of the fish were measured with an acoustic telemetry techniques in winter, 2015. Three wild Pacific codes WC1 to WC3 (total length 66.0, 75.0, 76.0 cm; body weight 2.84, 2.79, 3.47 kg, respectively) were tagged with the acoustic transmitter. WC1 tagged with an acoustic transmitter internally by surgical method, WC2 and WC3, externally with the acoustic data logger and a micro data logger for recording audible sound waves including timer release unit. The movement routes of the tagged fish were measured more than five hours using VR100 receiver and a directional hydrophone. The directionality of the fish movement was tested by Rayleigh's z-Test, the statistical analysis, and a statistical program SPSS. Three tagged fishes were individually released on the sea surface around the entrance to the Jinhae Bay on 10 to 24 January 2015. WC1 moved about 13.32 km with average swimming speed of 0.63 m/s for six hours. The average swimming depth and water depth of the seabed on the route of WC1 were 7.2 and 32.9 m, respectively. The movement range of WC2 and WC3 were 7.95 and 11.06 km, approximately, with average swimming speed of 0.44 and 0.58 m/s for 5.1 and 5.3 hours, respectively. The average swimming depth of WC2 and WC3 were 18.7 and 5.0 m, and the water depth on the route, 34.4 and 29.8 m, respectively. Three fishes WC1 to WC3 were shown significant directionality in the movement (p < 0.05). Movement mean angles of WC1 to WC3 were 77.7, 76.3 and $88.1^{\circ}$, respectively. There was no significant correlation between the movement direction of fish (WC1 and WC2) and the tidal currents during the experimental period (p >= 0.05). Consequently, three tagged fishes were commonly moved toward outside of the entrance and headed for eastward of the Korean Peninsula, approximately, after release. It may estimate positively that the tidal current speed may affect to the swimming speed of the Pacific cod during the spring tide than the neap tide.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.672-675
• /
• 2007

Experimental data are presented which describe heat losses of cavity type receiver in wind tunnel. Experiments are conducted at various conditions such as the heater temperature in cavity changes from 300, 400, and 500 oC, wind speed in tunnel from 2 to 8 m/s, and four different tilt angle of 30, 50, 70, 90o. The power consumption including temperature, voltage and current for each experimental conditions are measured and stored in data logger at everyone second interval. The experimental results show that heat losses increase with increasing wind speed and with tilt angle. However, heat losses for the tilt angle of 70 and 90o is almost same at each heater temperature. In addition, the effects of natural convection in combined convection heat losses vary in according to the tilt angle.

• 한국전자통신학회논문지
• /
• 제10권1호
• /
• pp.55-64
• /
• 2015

풍력시장은 매년 연 30%정도의 고도 성장률을 보이고 있으며, 점차 늘어나고 있는 추세이다. 국내 풍력발전기 설치 총량은 380MW로 전 세계시장의 0.2%의 점유율을 보이고 있다. 그러나 국내에 설치된 풍력발전기의 90%이상이 해외기업 제품이다. 또한 해상 풍력 발전소 설치를 위한 사전 조사 시스템에 적용되는 데이터로거도 대부분 해외기업 제품으로 막대한 비용이 해외로 유출되는 실정이다. 이에 본 논문에서는 풍력 발전기건설 업무의 효율성과 투자 비용절감을 위한 사전 기상자원 측정 시스템을 제안한다. 사전 기상자원 측정 시스템은 기상탑의 기상 관측 데이터로거 H/W와 무선 브리지, 기상탑 주변의 풍향, 풍속, 온 습도, 일사량, 데이터로거의 전력 상태를 모니터링할 수 있며, 측정된 데이터를 분석할 수 있는 Wind Rose S/W로 구성된 무선 통신(Wifi)기반의 해양 기상자원 측정 데이터로거 및 분석 모니터링 시스템이다.