• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.146-152
• /
• 2012

To install a wind power generator, the survey on the wind environment resources must be conducted in advance. The survey on the wind environment resources is to collect and analyze data regarding the wind speed and direction on a data logger. The data logger consists of a sensor, signal processing circuit and storage device. According to the analysis of the stored data, the amount of power generation by the types of generators can be predicted and the most optimal generator including safety grade can be selected, and in case of installing a generator in the future, it can be utilized as basic data regarding supporting base and foundation construction method of survey points. Data logger was developed for a small wind power generator that is suitable for the international standard(IEC 61400) by using DSP-F28335 micro controller in this paper. It was developed to measure the wind speed of 1 [m/s]~17 [m/s], the wind direction of 0 [$^{\circ}$]~359 [$^{\circ}$], and temperature of -30 [$^{\circ}C$]~50 [$^{\circ}C$], and the comparative experiment with other companies' data loggers was conducted, and an error was measured to be less than ${\pm}0.1$ [m/s] for wind speed and less than +1 [$^{\circ}$] for wind direction.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1352-1355
• /
• 1997

This paper presents the algorithm for estimating the attitude of an underwater vehicle using EFK. The system model is designed by linerizing the nonlinear Euler angle differential equation and the measurements is a speed logger output. The simulation result shows that the estimation lagorithm is adequate for decreasing attitude errors that grow abruptly during the motion with acceleration and rotation. It also shows that we can adapt the algorithm for compensating initial attitude errors generated after initial leveling.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.2
• /
• pp.166-171
• /
• 2015

Recently, the international standard RS-422 serial communication, which was primarily designed for the communications between micro-controllers, has been used as a communication method on the ship. However, as the NMEA (National Marine Electronics Association) 2000 standardization progresses recently, a high-speed Ethernet-based communication environment is expected to be an alternative communication method instead of the RS-422 gradually. In addition, the ship's main instrumentation equipment with versatility and convenience is implemented to control devices as monitoring and controlling tools. This paper describes an implementation of wireless ultrasonic anemometer and anemoscope data processing and logger system using PC network, where the control processing equipment such as a separate operational console, data-logger, and indicator is required for the system. For these, the related element technologies to implement ultrasonic anemometer and anemoscope data processing system are expressed as a functional modules, and the NMEA 2000 standard certified data-logger system is implemented without the separate operational console.

• Wind and Structures
• /
• v.14 no.4
• /
• pp.337-357
• /
• 2011

The collection of wind speed time series by means of digital data loggers occurs in many domains, including civil engineering, environmental sciences and wind turbine technology. Since averaging intervals are often significantly larger than typical system time scales, the information lost has to be recovered in order to reconstruct the true dynamics of the system. In the present work we present a simple algorithm capable of generating a real-time wind speed time series from data logger records containing the average, maximum, and minimum values of the wind speed in a fixed interval, as well as the standard deviation. The signal is generated from a generalized random Fourier series. The spectrum can be matched to any desired theoretical or measured frequency distribution. Extreme values are specified through a postprocessing step based on the concept of constrained simulation. Applications of the algorithm to 10-min wind speed records logged at a test site at 60 m height above the ground show that the recorded 10-min values can be reproduced by the simulated time series to a high degree of accuracy.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.819-826
• /
• 2000

This study was performed to develop a measurement system of tractor field performance for plow and rotary operations. Measurement system for tractor consisted of torque sensors to measure torque of drive axles and PTO axle, speed sensors to measure rotational speed of drive axles and engine, microcomputer to control data logger, and data logger as I/O interface system. The measurement system was installed on four-wheel-drive tractor. Four-element full-bridge type strain gages were used for torque measurement of drive axles and optical encoders were used to measure speeds of drive axles and engine. Slip rings were mounted on the rotational axles. Signals from sensors were inputted to data logger that was controlled by microcomputer with parallel communication. Sensors were calibrated before the field tests. Regression equations were found on completion of the calibrations. The field experiment was performed at paddy fields and uplands. Rotary and plow were used when the tractor was operated in the field. Travelling speeds of the tractor were 1.9 km/h, 2.7 km/h, 3.7 km/h, 5.5 km/h, 8.2 km/h, and 11.8 km/h. Operating depths of implements were maintained approximately 20cm during the tests. Torque data of drive axles were different at each location during plow and rotary operations. Results showed that torque of rear axles were greater than those of front axles. Total torque were 6860 - 11064 Nm at the upland and 7360 - 14190 Nm at the paddy field for plow operations. It was found that torque at the paddy field were about 20% greater than those at the upland for plow operations. Torque data showed that rotary operations required less power than plow operation at the paddy field and the upland. Torque measurements at each axle for rotary operations were only 8 - 16% of plow operations in the upland and 15 - 20% in the paddy field.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.375-383
• /
• 2011

This paper describes a real-time hardware simulator for a grid-tied Permanent Magnet Synchronous Generator (PMSG) wind power system, which consists of an anemometer, a data logger, a motor-generator set with vector drive, and a back-to-back power converter with a digital signal processor (DSP) controller. The anemometer measures real wind speed, and the data is sent to the data logger to calculate the turbine torque. The calculated torque is sent to the vector drive for the induction motor after it is scaled down to the rated simulator power. The motor generates the mechanical power for the PMSG, and the generated electrical power is connected to the grid through a back-to-back converter. The generator-side converter in a back-to-back converter operates in current control mode to track the maximum power point at the given wind speed. The grid-side converter operates to control the direct current link voltage and to correct the power factor. The developed simulator can be used to analyze various mechanical and electrical characteristics of a grid-tied PMSG wind power system. It can also be utilized to educate students or engineers on the operation of grid-tied PMSG wind power system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.2
• /
• pp.184-190
• /
• 2014

Until now ship communication micro serial network communication method is designed for the communication between the controller and the RS-422 communication on the international standard ISO 1993, but gradually progresses NMEA 2000 standardized fast Ethernet-based communications environments expected to be replaced. In addition, the ship's main instrumentation equipment versatility with ease gradually to control devices by monitoring and controlling are. Wind anemometer, ship mast end, where the highest wind farms typically install a separate console boxes, data loggers, indicators was required in order to manage them, to maintain them, to go through the procedures and cumbersome data update firmware were Therefore, in this paper, using the PC network, ultrasonic wind speed data processing system for implementing functional was expressed as a function of the technology elements, NMEA 2000 standard certified in separate operating console without the features of the data loggers, indicators, implementation by ultrasonic wind data processing system was implemented to minimize the maintenance cost of the operating system.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.1
• /
• pp.29-38
• /
• 2019

In order to investigate the behavioral characteristics of Pacific cod (Gadus macrocephalus) released at the entrance of Jinhae Bay, Korea, the direction and range of movement, swimming speed of the fish were measured with an acoustic telemetry techniques in winter, 2015. Three wild Pacific codes WC1 to WC3 (total length 66.0, 75.0, 76.0 cm; body weight 2.84, 2.79, 3.47 kg, respectively) were tagged with the acoustic transmitter. WC1 tagged with an acoustic transmitter internally by surgical method, WC2 and WC3, externally with the acoustic data logger and a micro data logger for recording audible sound waves including timer release unit. The movement routes of the tagged fish were measured more than five hours using VR100 receiver and a directional hydrophone. The directionality of the fish movement was tested by Rayleigh's z-Test, the statistical analysis, and a statistical program SPSS. Three tagged fishes were individually released on the sea surface around the entrance to the Jinhae Bay on 10 to 24 January 2015. WC1 moved about 13.32 km with average swimming speed of 0.63 m/s for six hours. The average swimming depth and water depth of the seabed on the route of WC1 were 7.2 and 32.9 m, respectively. The movement range of WC2 and WC3 were 7.95 and 11.06 km, approximately, with average swimming speed of 0.44 and 0.58 m/s for 5.1 and 5.3 hours, respectively. The average swimming depth of WC2 and WC3 were 18.7 and 5.0 m, and the water depth on the route, 34.4 and 29.8 m, respectively. Three fishes WC1 to WC3 were shown significant directionality in the movement (p < 0.05). Movement mean angles of WC1 to WC3 were 77.7, 76.3 and $88.1^{\circ}$, respectively. There was no significant correlation between the movement direction of fish (WC1 and WC2) and the tidal currents during the experimental period (p >= 0.05). Consequently, three tagged fishes were commonly moved toward outside of the entrance and headed for eastward of the Korean Peninsula, approximately, after release. It may estimate positively that the tidal current speed may affect to the swimming speed of the Pacific cod during the spring tide than the neap tide.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.672-675
• /
• 2007

Experimental data are presented which describe heat losses of cavity type receiver in wind tunnel. Experiments are conducted at various conditions such as the heater temperature in cavity changes from 300, 400, and 500 oC, wind speed in tunnel from 2 to 8 m/s, and four different tilt angle of 30, 50, 70, 90o. The power consumption including temperature, voltage and current for each experimental conditions are measured and stored in data logger at everyone second interval. The experimental results show that heat losses increase with increasing wind speed and with tilt angle. However, heat losses for the tilt angle of 70 and 90o is almost same at each heater temperature. In addition, the effects of natural convection in combined convection heat losses vary in according to the tilt angle.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.55-64
• /
• 2015

Wind turbine market is showed height growth rate of about 30% for year, and is increasingly growing. Total rate of domestic wind turbine installation is showing share of 0.2% of the global market that is 380MW. However, wind turbine installed in domestic are foreign product more than 90%. Similarly, Datalogger of pretest system for ocean wind turbine plant installation has been leaked huge cost to abroad by mostly abroad company product. In this paper, we proposed pretest weather resource measurement system for efficiency and investment cost cutting of wind turbine construction work. Preset weather resource measurement system is ocean weather resource measurement datalogger based on wireless communication(wifi) that have consist of hardware and software(wind rose) that is able to monitoring as datalogger of wireless bridge and battery state, wind direction, wind speed, temperature, humidity, radiation around weather tower and is able to analysis of measured data.