• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.18-24
• /
• 2018

This paper focuses on systematic design about the membership ranges of the main design factors such as control error, control error rate, and sampling time for the fuzzy logic control of the variable speed drive refrigeration cycle. The upper and the lowest limit of the membership ranges are set up from the data of static characteristics obtained by experiments. Three kinds of membership ranges on the control error and the control error rate are tested by experiments. Especially, an effect of sampling time on control performance is also investigated in the same way. Experimental data showed the control error rate and the sampling time strongly effected on the control performance of the refrigeration cycle with a variable speed drive.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.114-121
• /
• 2017

In order to overcome the limitations of the mobile speed system for 1 lane, this study is used a multi-laser beam to develop a mobile speed measuring system, using a multi-phase beam. By using multi-laser beam, least squares algorithms and speed error processing algorithms were developed to improve speed accordancy and speed error rates compared to conventional mobile speed meters using a single laser beam. A field test showed that 80.0 percent of 3 lane and 87.0 percent of 4 lane were appropriate for the mobile speed system. With the development of the mobile speed measuring system, it is expected to dramatically reduce the accidents caused by the speed of traffic. It is also expected to effectively operate equipment and manage the cost by improving manpower and providing improved enforcement accuracy, by contributing positively to public institution and public affairs.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.4
• /
• pp.57-63
• /
• 2010

The damping parameter of Levenberg-Marquardt algorithm switches between error backpropagation and Gauss-Newton learning and affects learning speed. Fixing the damping parameter induces some oscillation of error and decreases learning speed. Therefore, we propose the way of a variable damping parameter with referring to the alternation of error. The proposed method makes the damping parameter increase if error rate is large and makes it decrease if error rate is small. This method so plays the role of momentum that it can improve learning speed. We tested both iris recognition and wine recognition for this paper. We found out that this method improved learning speed in 67% cases on iris recognition and in 78% cases on wine recognition. It was also showed that the oscillation of error by the proposed way was less than those of other algorithms.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.10A
• /
• pp.1532-1538
• /
• 1999

In general, because error rate of wireless link is higher than that of wired link, DLC layer protocol for wired network with low error rate is not proper for wireless environments. In addition, the conventional DLC layer protocol for wireless network is optimized for the low-speed data service, so it is difficult to use conventional DLC protocol in the current mobile communication environments handing high-speed and multimedia services. Therefore, a DLC layer protocol that is suitable to current wireless communication environments is required. In this paper, we propose a novel error control scheme that supports a variety of traffic attribute and is applicable to high-speed and multimedia data service in WATM. The proposed scheme provides enhanced throughput performance for real-time traffic by using modified ASR ARQ without ACK and reduces loss rate by using FEC in the case of high error condition. Also, for non real-time traffic, the use of ASR ARQ without ACK enhances throughput performance and delay time is decreased by using FEC in the case of high error rate channel. As a result of simulation, the proposed scheme has better performance than conventional ASR ARQ protocol in view of delay and throughput.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.266-272
• /
• 2002

High-speed machining is one of the most effective technology to improve productivity. Because of the high speed and hugh fried rate, high-speed machining can alive great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on machining accuracy is discussed fur the results of surface roughness and machining error in Z-direction of the high speed machining.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.329-334
• /
• 2002

High-speed machining is one of the most effective technology to improve productivity. Because of the high speed and high feed rate, high-speed machining can give great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining. Depth of cut, feed rate, spindle revolution and cutting force are control factors. The effect of the control factors on machining accuracy is discussed for the results of surface roughness and machining error in Z-direction for the high speed machining of STD11.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.9
• /
• pp.6-13
• /
• 1993

In is well-known that system performance in the high speed digital radio communication system is usually deteriorted due to the frequency selective fading distortion. In this paper, bit error rate(BER) performance by the reception phase error in cellular mobile communication systems is derived and analyzed. The system is modeled as a frequency selective fast Rayleigh fading channel corrupted by additive white gaussian noise(AWGN) and co-channel interference(CCI). Our numerical results show that for the 24KBaud(48Kb/s) $\pi$/4-DQPSK operated at carrier frequency 800 MHz and C/I<20 dB, the BER will be dominated by CCI if the vehicular speed is below 100 Km/h. The results show that performance, when reception phase error is below $\pi$/12, is deterioreted less than 3 dB, and that performance, when reception phase error is above $\pi$/12, is degraded over 3 dB.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.33 no.2
• /
• pp.154-161
• /
• 2010

The conning display which is located in the ship bridge shows the various important information such as ship position, ship speed, track data, rate of turn, thruster rpm so on, and is one of the IBSs(Integrated Bridge Systems). In this study, the survey was conducted for ten officers to find the importance and using frequency of the information which were displayed in the conning display. The results showed that the information of drift speed, ship speed, wind direction and wind force, rate of turn, sea water depth, ship position, heading, thrust rpm, alarm, rudder command and angle got high scores and it meant that these information were very important and high frequency of use during the navigation. The optimized contents arrangement in conning display was suggested based on importance and using frequency of information. The experiment using eye-tracking system was conducted to compare the performance time and error rate of nine different scenarios for suggested arrangement display and three other existing displays. The results showed that the suggested arrangement was the best in performance time and error rate. The scenario concerning the direction and speed of wind showed faster performance time and lower error rate than other scenarios. The movement of subject's eye tended to search from the center and to avoid the comer, called 'the comer effect.' It is expected that the results of this study could help for the bridge staff to grasp the sailing information easily and to cope with the given situations promptly.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.2
• /
• pp.55-64
• /
• 2010

This study tried to focus on nontraditional job that has not been studied in terms of the subjects associated with MSDs(Musculoskeletal Disorders). Specifically, dental procedure was the job to be analyzed in this study. An alternative method as well as a traditional method for viewing teeth while performing simulated dental procedures. Four graduated students did both methods(direct view and indirect view) as the subjects in this study. The method based on indirect view used a video camera and monitor to view the teeth. The experiment was conducted five times for each subject. The major findings in this study were as follows; 1) Job speed was increased with the repetitions for both methods, 2) Difference of Neck flexion between direct and indirect methods was statistically siginificant(Neck flexion for indirect method was dramatically decreased), 3) Difference of job speed between direct and indirect methods was statistically significant(Job speed for direct method was faster than that of indirect method), 4) Difference of error rate between direct and indirect methods was statistically significant(error rate for direct method was lower than that of indirect method), 5) Even though indirect method did not provide better performance in terms of job speed and error rate yet, it seemed to need a trade-off between two methods in the future since indirect method provided better working postures than that of direct method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.15-24
• /
• 2021

In this paper, to analyze the types of surface morphology error according to factors that cause machining error, the experiments were conducted in the ultra-precision diamond machine using a diamond tool. The factors causing machining error were classified into the pressure variation of compressed air, external shock, tool errors, machining conditions (rotational speed and feed rate), tool wear, and vibration. The pressure variation of compressed air causes a form accuracy error with waviness. An external shock causes a ring-shaped surface defect. The installed diamond tool for machining often has height error, feed-direction position error, and radius size error. The types of form accuracy error according to the tool's errors were analyzed by CAD simulation. The surface roughness is dependent on the tool radius, rotational speed, and feed rate. It was confirmed that the surface roughness was significantly affected by tool wear and vibration, and the surface roughness of Rz 0.0105 ㎛ was achieved.