• 한국지진공학회논문집
• /
• 제24권1호
• /
• pp.39-47
• /
• 2020

Lightly reinforced concrete (RC) moment frames may suffer significant damage during large earthquake events. Most buildings with RC moment frames were designed without considering seismic loads. The load-displacement response of gravity load designed frames could be altered by masonry infill walls. The objective of this study is to investigate the load-displacement response of gravity load designed frames with masonry infill walls. For this purpose, three-story gravity load designed frames with masonry infill walls were considered. The masonry infilled RC frames demonstrated larger lateral strength and stiffness than bare RC frames, whereas their drift capacity was less than that of bare frames. A specimen with a partial-height infill wall showed the least drift capacity and energy dissipation capacity. This specimen failed in shear, whereas other specimens experienced a relatively ductile failure mode (flexure-shear failure).

• 대한설비공학회지:설비저널
• /
• 제17권6호
• /
• pp.708-716
• /
• 1988

Local heat transfer coefficients were measured on semi-cylinders on which a circular water jet impinged in crossflow. The ratio of the semi-cylinder's diameter and the nozzle outlet diameter were varied parametrically, as were the Reynolds number and the supplementary water heights. The measurements showed that the circumferential distribution of the heat transfer coefficient peaked at the stagnation point. For a fixed supplementary water height, the peak heat transfer coefficient was not depend on the curvature of test specimen(d/D). Optimum height of supplementary water which brought about the augmentation of heat transfer at the stagnation point was S/D=1. The Nusselt number decreased as the circumferential distance or angle increased. The circumferential distribution of dimensionless heat transfer (Nu/Nus) was independent of d/D ($d/D{\geq}8.33$), but for the d/D<8.33, it was depended on d/D. At a fixed angle of specimen, dimensionless heat transfer (Nu/Nus) decreased as the ratio d/D increased. The extent of the decrease between d/D=6.67 and 8.33 was markedly greater than that between d/D=8.33 and 10, or d/D=10 and 11.67.

• Composites Research
• /
• 제29권5호
• /
• pp.231-235
• /
• 2016

본 연구에서는 동일한 구조의 모자형 보강재를 이용하여 일체형 동시접착 구조의 보강패널시편을 제작하였다. 일반적인 동시접착 보강패널 시편과 탄소에폭시 복합재를 이용하여 제작된 카울플레이트(Caul Plate)를 적용한 동시접착 보강패널 시편의 2가지 형태 시편을 제작하였으며 일반 동시접착 보강패널 시편에서는 패널 상에서 보강재가 적용되지 않은 부위가 적용된 부위보다 더 두꺼운 패널 두께를 가지고 그 연결부위에는 0.61 mm 높이 및 3.29 mm 길이의 플라이웨이브 현상이 나타났다. 카울플레이트가 적용된 보강패널 시편에서는 보다 균일한 압력 전달로 인하여 0.22 mm 높이와 1.37 mm 길이의 완화된 웨이브 현상을 보이면서 약 50% 이상 개선된 결과를 얻을 수 있었다.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.157-163
• /
• 1996

This paper is concered on the development of low-cost fine blanking die with two fluid chambers of which the pressure can be controlled by a hydraulic unit and its application to producting circular blanks in a conventional hydraulic press, not in a special triple-action press usually adopte in fine blanking operation. Four important working parameters affecting on the precision accuracy of products such as existence and position of Vee-ring, stripping force and counter punching force are primarily considered for experiments. Finite element analysis by suing ABAQUA software is approxi- mately made for blanking of circular specimen with a flat stripper plate and then compared with experimental measurements. The the theoretical prediction of camber height which represents deflection of a dish-shaped specimen after blanking seems to give a qualitatively good agreement. It is shown through experiments the the camber height decreases with decreasing stripping force and also with increasing counter punching force, but particularly depending on the latter much more than the former.

• Computers and Concrete
• /
• 제23권4호
• /
• pp.281-294
• /
• 2019

The post-fire behavior of structural elements and the cooling process has always been one of the main concerns of the structural engineers. The structures can be cooled at different rates, where they affect the structure's behavior. In the present study, a numerical model has been developed using the Abaqus program to investigate the effect of cooling rate on the post-fire behavior of the CFST column. To verify the model, results of an experimental study performed on CFST columns within a full heating and cooling cycle have been used. In this model, coMParison of the residual strength has been employed in order to examine the behavior of CFST column under different cooling rates. Furthermore, a parametric study was carried out on the strength of steel and concrete, the height of the specimens, the axial load ratio and the cross-sectional shape of the specimen through the proposed model. It was observed that the cooling rate affects the behavior of the column after the fire, and thus the higher the specimen's temperature is, the more effect it has on the behavior. It was also noticed that water cooling had slightly more residual strength than natural cooling. Furthermore, it was recognized from the parametric study, that by increasing the strength of steel and concrete and the load ratio, as well as modifying the cross-sectional shape from circular to square, residual strength of column at the cooling phase was less than that of the heating phase. In addition, with reducing column height, no change was witnessed in the column behavior after the cooling phase.

• 한국지반환경공학회 논문집
• /
• 제20권1호
• /
• pp.67-74
• /
• 2019

동상은 동토지역에서 발생하는 대표적인 공학적 특성이다. 계절동토(seasonal frost area)에 해당하는 우리나라는 동결융해에 의한 구조적 피해가 발생하고 동상에 관한 연구의 필요성이 증대되고 있는 실정이다. 본 논문에서는 새롭게 개발한 투명 온도제어형 셀을 활용하여 동상에 관한 연구를 수행하였다. 동상에 민감한 흙을 인공적으로 조성하여 동상민감성 판정에 있어 중요한 인자 중 하나인 물 주입속도(water intake rate)에 관한 분석을 실시하였다. 간극수 동결에 의한 부피팽창(heave by pore water)이 수렴하는 시점 이후에 동상속도(frost heave rate)와 물 주입속도는 거의 유사하게 나타났다. 그러나 물 주입속도를 측정하기 위해 상부 페더스탈에 설치한 O-ring은 몰드 내벽과의 마찰을 발생시켜 동상발생을 저하시켰다. 따라서 물 주입속도를 활용한 동상민감성 판정 기준은 신뢰하기 힘들다고 판단되었으며, 유사한 거동을 보이는 동상속도를 활용하는 것이 적절하다는 결론을 내렸다. 또한, 동상민감성 흙을 활용해 시료크기가 동상에 미치는 영향을 파악하고자 하였다. 시료크기가 다른 2가지 경우에 대해 동상시험을 수행하였으며 상재하중, 온도구배, 그리고 건조단위중량을 동일하게 설정하였다. 실험결과를 토대로 시료크기는 동상에 영향을 미치지 않는다는 것을 발견하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제9권3호
• /
• pp.1-6
• /
• 1981

This study examined the radial variations in element demensions of mongolian oak (Quercus mongolica.), elm (Ulmus japonica.), maackia(Maackia amurensis.), castor aralia (Kalopanax pictus.) from pith outwards. Disks were cut from the d.b.h.(above 1.2m) of each species and specimen for tangential pore diameters, fiber length, ray height and width were taken from 1-3rd, 5th, 10th, 15th.............40th ring number from pith. The tangential pore diameters in the earlywood increased rapidly near the pith and then maintained almost constant or very gradually increased diameters in about 20th-30th ring number from pith. In the latewood, tangential pore diameters gradually increased from pith to outwards though the increment is smaller than in early wood. Radial variations of ray height and width maintained almost constant, gradually increased or rapidly increased diameters and then maintained almost constant from pith to outwards. Patterns of radial variations in the fiber length were almost coincident with patterns of earlywood pore diameters, and of ray height or width in Ulmus japonica and Maackia amurensis.

• 소성∙가공
• /
• 제3권3호
• /
• pp.291-301
• /
• 1994

In the simultaneous forward-backward extrusion the effects of some process variables including area reduction, stroke advance, materials(Al 2024 and commercial pure copper) on the extrusion load, plastic flow and height ratio of upper to lower extruded parts are experimentally investigated and analyzed. Grid-marking technique is employed to visualize the plastic flow. The influence of using split and original specimen on the extrusion load and height ratio is evaluated by experiments. Experimental results show that the plastic flow if oriented to the part of lower area reduction in the begining but it is usually variated during the overall process. The configurations of plastic deformation and plastic flow are dependent on the working materials and the lubricational conditions.

• 소성∙가공
• /
• 제20권5호
• /
• pp.339-343
• /
• 2011

This paper presents methods for analyzing the extent of cylindrical-shaped void closure. In addition, a quantitative relationship between change in void fraction and height reduction ratio of a compressed specimen is proposed. The height reduction ratio, number of deformation steps and billet rotation were chosen as key process parameters influencing the void closing behavior, namely, the changes in void shape and size during hot open die forging of a large ingot. The extent of void closure was analyzed from microscopic observations and estimated from tensile test results. The tensile strengths of specimens with closed voids and those without were compared for various reduction ratios in height. The results confirmed that void closure occurs at reduction ratios greater than 30 %. The void closing behavior could be expressed as a hyperbolic tangent function of reduction ratio in height, number of paths, and billet rotation. The knowledge presented in this paper could be helpful for optimizing deformation paths in open die forging processes.

• 한국강구조학회 논문집
• /
• 제23권1호
• /
• pp.125-135
• /
• 2011

최근 타워형 아파트구조에 많이 사용되고 있는 무량판 구조시스템을 대신해 층고절감 및 장스팬 구현 그리고 내화성능향상을 목적으로 GFRP를 이용한 경량합성바닥을 개발하였다. GFRP를 이용한 경량합성바닥은 웨브에 개구부를 가지는 비대칭 강재보 하부에 GFRP를 부착하고 슬래브에 경량체를 삽입한 중공합성바닥이다. 이에 개발된 합성바닥의 휨성능을 평가하기 위해 GFRP, 중공률, 웨브의 개구부 등을 변수로 실대 실험을 수행하였다. 그 결과 GFRP를 이용한 합성보 실험체는 기준 실험체에 비해 휨내력 및 강성 측면에서 10% 높은 성능을 나타냈으며, 구조물이 항복할 때까지 완전합성거동하였다. 항복 이후 웨브개구부 주변의 응력집중현상에 의해 연성이 감소하는 현상이 나타났으며, 최대내력점까지 미끄러짐의 발생은 미소하였다. 내력설계 측면에서는 안전율을 고려해 해석값의 85%를 설계내력으로 평가하는 것이 타당한 것으로 나타났다.