• 한국농공학회지
• /
• 제30권2호
• /
• pp.82-94
• /
• 1988

The purpose of this study is to introduce the Double Punch test method which is an indirect testing method of tensile strength of concrete, and to compare with the tensile strength of concrete as determined by the split-cylinder test, a practical method for performing the Double Punch test to obtain the tensile strength of concrete is proposed and recommended for general use. In this study, the dimensions of cylindrical specimens used in the Double-Punch test were 15X30cm, 15X15cm, 10${\times}$(20cm, and 5${\times}$l0cm, and in the split-cylinder test were 15${\times}$(30cm, 15${\times}$(15cm, and 10${\times}$(20cm. And the diameters of loading punches used in the Double-Punch test were 1.5cm, 2.5cm, and 3.5 cm. The results obtained from tests are summarized as follows ; 1. In the split-cylinder test, the tensile strength of concrete by the linear elasticity theory is similar to that of plasticity theory. 2. Both split-cylinder test and Double-Punch test, tensile strength of concrete is increased with decreasing specimen size. This tendency is identical when the ratio of specimen diameter to height is 1: 2, but that tendency is quite different when the ratio is 1: 3. In the Double-Punch test, if specimen size is constant, by increasing the punch size, tensile strength of concrete is increased, too. 4. Using a 15 ${\times}$( 15 cm cylinder specimen and 3.5 cm diameter punch in the Double Punch test would give the most uniform and consistent result in tensile strength, and the result showed a gQod correlation with splitting tensile strength from 15 x 30cm specimen. 5. In order to obtain satisfactory results and to nuninuze variability, it is proposed that specimens of 15 cm in diameter and 15 cm in height with two 3.5 cm diameter punches should be used. It seems, therefore, reasonable tt) take f't=0.0024 P(kg / cm$^2$) as a working formula for computing the tensile strength in the Double Punch test for concrete.

• KIEAE Journal
• /
• 제8권3호
• /
• pp.77-83
• /
• 2008

The effective mixture of structural laminated timber and other materials is expected to extend the potentials of building structures because of the potentials to realize high performance in structural safety. The classical joint types using drift pin and bolts are occurred local failures due to the small bearing area. In result, new joints using H shaped steel were suggested in this research. The objective of this study is to evaluate elasto-plastic behaviors by strengthening types of wood frames with new joints connecting structural laminated timber with H shaped steel. A total of five specimens of about one-second scale were tested. Specimens had columns with 1,050 height and $84mm{\times}100mm$ section, and a beams with 1,950mm length and $130mm{\times}100mm$ section. Also, the specimens were stiffened by brace, hwang-toh brick, and autoclaved lightweight concrete. The results of the test showed that the specimen stiffened with autoclaved lightweight concrete was characterized by fairly good strength and stiffness than those of the other specimens. Initial stiffness of H-2.0D-NS specimen with 2 times inserting length of beam height showed 1.33 times than that of H-1.5D-NS specimen. However, the strength of H-2.0D-NS specimen has not improved too much than H-1.5D-NS specimen.

• 한국조경학회지
• /
• 제26권2호
• /
• pp.229-239
• /
• 1998

This study investigated ecological and growth characteristics of Sorbus alnifolia for usage of landscape woody plant. The results are obtained as follows: 1) The results of investigate the native Sorbus alnifolia vegetations in Seoul and Kyonggi-do are as follows. From the investigation of canopy and understory, Pinus densiflora, Pinus rigida, Quercus mongolica Quercus dentata and Quercus aliena grow well in natural habitat of Sorbus alnifolia. While Rhod. mucronulatum, Symplocos chinensis, Corylus hetrophylla and alnifolia. While Rhod. mucronulatum, Symplocos chinensis, Corylus hetrophylla and Lindera obtusiloba are commonly found from shrub structure in the habitat. These structure pattern of natural setting would be applied for ecological planting design. 2) The Mt. Rabong area, which locates near a heavy factory district and is considered as environmental dteriorated area has the lowest soil acidity range among three investigated area. Sorbus alnifolia grows in where contains low soil acidity and inorganic nutrient. It might concluded that Sorbus alnifolia be tolerates to air pollution. 3) From the investigation of good specimen tres, the oldest good specimen trees of Sorbus alnifolia have grown in Seoul and Kyonggi-Do for 130 years with 15m height and 12m width. Most of good specimen trees are over 50 years old with 10~15m height, 4.5-12m width. These growth shape and form could be recommend that Sorbus alnifolia would be used as street tree and landscape woody plant in urban park.

• Geomechanics and Engineering
• /
• 제19권2호
• /
• pp.193-199
• /
• 2019

A frozen fringe plays a key role in frost heave development in soils. Previous studies have focused on the physical and mechanical properties of the frozen fringe, such as overall hydraulic conductivity, water content and pore pressure. It has been proposed that the thickness of the frozen fringe controls frost heave behavior, but this effect has not been thoroughly evaluated. This study used a temperature-controllable cell to investigate the impact of frozen fringe thickness on the characteristics of frost heave. A series of laboratory tests was performed with various temperature boundary conditions and specimen heights, revealing that: (1) the amount and rate of development of frost heave are dependent on the frozen fringe thickness; (2) the thicker the frozen fringe, the thinner the resulting ice lens; and (3) care must be taken when using the frost heave ratio to characterize frost heave and evaluate frost susceptibility because the frost heave ratio is not a normalized factor but a specimen height-dependent factor.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권5호
• /
• pp.9-15
• /
• 2023

이 연구에서는 적층시험체 제작 방식에 따른 시멘트계 복합재료의 적층성능과 강도특성을 분석하였다. 레이어 높이에 따른 적층성능평가결과, 직선부과 곡선부에서 레이어 높이가 10 mm일 때 가장 높은 치수 안정성을 나타내었다. 몰드 타설 시험체와 Printing-Z 시험체의 재령 28일 압축강도는 동일한 압축강도 성능을 나타내었다. 반면, Printing-X 시험체의 재령 28일 압축강도는 71.72 MPa로 가장 낮았으며, 몰 드 제작 시험체와 Printing-Z시험체 대비 평균 8%가 낮은 압축강도를 나타내었다. 적층시험체의 쪼갬인장강도는 몰드 제작 시험체와 유사한 성능을 나타낼 수 있으나, 하중 가력방향에 대한 레이어의 방향과 시험체 내 레이어의 개수에 따라 10% 이상의 강도성능 저하현상이 나타날 수 있다. X-ray CT 분석을 통한 적층시험체의 계면 분석결과, 레이어의 계면을 따라 일정한 크기의 공극이 분포함을 확인하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.182-183
• /
• 2014

In case of large soft body impact test at the construction site, the test conditions are different from conditions at the laboratory, and the length of rope to hold the impact specimen must be changed. In a previous study, the fact that the size of impact load is varied by the length of rope on the large soft body impact specimen was confirmed. In this study, the length of rope and fall height were set as independent variables to conduct the load analysis test. It was determined that the load fluctuation was occurred depending on the length of rope under the fall height over 100 mm, and it is concluded that the additional setup of fall height to modify the actual impact load size is required when the length of rope is below 2.5 m. In this study, the modified formula to put equal size of impact load regardless of the length of rope was extracted through the experiment.

• Design & Manufacturing
• /
• 제12권3호
• /
• pp.19-24
• /
• 2018

Fused deposition Modeling (FDM) is one of the most widely used for the prototype of parts at ease. The FDM 3D printing method is a lamination manufacturing method that the resin is melted at a high temperature and piled up one by one. Another term is also referred to as FFF (Fused Filament Fabrication). 3D printing technology is mainly used only in the area of prototype production, not in production of commercial products. Therefore, if FDM 3D printer is applied to the product process of commercial products when considered, the strength and dimensional accuracy of the manufactured product is expected to be important. In this study, the mechanical properties of parts made by 3D printing with FDM method were investigated. The aim of this work is to examine how the mechanical properties of the FDM parts, by changing of processing FDM printing direction and the height of stacking layer is affected. The effect of the lamination direction and the height of the stacking layer, which are set as variables in the lamination process, by using the tensile specimen and impact specimen after the FDM manufacturing process were investigated and analyzed. The PLA (Poly Lactic Acid) was used as the filament materials for the 3D printing.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 가을 학술논문 발표대회
• /
• pp.193-194
• /
• 2022

The use of high-strength grout for facility foundations and bridges has recently been expanding in offshore wind farms. Offshore wind farms require a bearing capacity for horizontal loads such as wind, waves. Therefore, in this study, the strength of the high-strength grout discharged through pump pressure was measured and compared with the existing strength to secure the strength after the underwater pump pressure of the high-strength grout used in the offshore wind connection. The compressive strength measurement showed that the strength difference at each position of the core specimen was 1% higher than that of the other specimens, and there was almost no change in the strength according to the height. The strength of the core specimen decreased by 23% compared to the existing strength, which is similar to the result of this study because the strength of the core specimen decreased by approximately 25% compared to the general specimen according to related research. Therefore, it is believed that there is no decrease in strength due to underwater pumping.

• Wind and Structures
• /
• 제13권1호
• /
• pp.21-36
• /
• 2010

A new full scale testing apparatus generically named the Wall of Wind (WoW) has been built by the researchers at the International Hurricane Research Center (IHRC) at Florida International University (FIU). WoW is capable of testing single story building models subjected up to category 3 hurricane wind speeds. Depending on the relative model and WoW wind field sizes, testing may entail blockage issues. In addition, the proximity of the test building to the wind simulator may also affect the aerodynamic data. This study focuses on the Computational Fluid Dynamics (CFD) assessment of the effects on the quality of the aerodynamic data of (i) blockage due to model buildings of various sizes and (ii) wind simulator proximity for various distances between the wind simulator and the test building. The test buildings were assumed to have simple parallelepiped shapes. The computer simulations were performed under both finite WoW wind-field conditions and in an extended Atmospheric Boundary Layer (ABL) wind flow. Mean pressure coefficients for the roof and the windward and leeward walls served as measures of the blockage and wind simulator proximity effects. The study uses the commercial software FLUENT with Reynolds Averaged Navier Stokes equations and a Renormalization Group (RNG) k-${\varepsilon}$ turbulence model. The results indicated that for larger size test specimens (i.e. for cases where the height of test specimen is larger than one third of the wind field height) blockage correction may become necessary. The test specimen should also be placed at a distance greater than twice the height of the test specimen from the fans to reduce proximity effect.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.781-784
• /
• 2008

최근 고강도콘크리트의 현장적용이 증가하면서 현장 콘크리트의 품질확인을 위한 강도 측정시 고강도콘크리트 공시체와 안전진단시 채취되는 비표준형 공시체의 사용이 증가하고 있다. 이에 본 연구에서는 콘크리트의 가장 기본적인 재료특성인 압축강도 특성을 공시체에 대한 크기 효과와 강도수준을 고려하여 합리적인 관계식을 적립하고자 하였다. 실험결과, 공시체 크기 1mm 증가시마다 압축강도는 기준강도 24MPa에서 0.05MPa, 40MPa에서 0.1MPa, 80MPa에서 0.3MPa씩 감소시키는 것으로 나타나, 강도수준이 고강도화 될수록 압축강도 감소량은 증가하는 것으로 나타났다. 또한 공시체 높이/직경비가 1.0 증가시마다 압축강도는 24MPa에서 2.9MPa, 40MPa에서 3.7MPa, 80MPa에서 9.8MPa 감소되어 고강도콘크리트일수록 높이/직경비의 영향을 크게 받는 것으로 나타났다.