• New & Renewable Energy
• /
• v.1 no.4 s.4
• /
• pp.55-59
• /
• 2005

In this paper, a new drive system(SHS) for hybrid electric vehicle is proposed. As dual rotor hybrid electric vehicle using planetary gearsets, the SHS has the advantages of both series and parallel systems. The output speed and torque of SHS can be determined at specific point regardless of the engine's operating point. When the size of generator which is used in SHS is same as in THS, the SHS has more activities of engine control due to the ability that is operated in lower speed range. To maximize the performance of system, we carried out optimization for the three parameters that are engine, motorl and motor2. As the result of the optimization, we confirmed the SHS is more preferable to THS in fuel consumption and acceleration area.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.59-64
• /
• 2002

The effects of EGR on emissions were investigated by using a six-cylinder, 8 litre, turbo-charged, heavy-duty diesel engine with a low pressure route EGR system. The experiments were performed at various engine loads while the EGR rates were set from 0% to 30%. Hot and cooled EGR are achieved without cooling and with cooling respectively. To verify the possibility of EGR technology for the applications, test were performed with steady state test cycle. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke and PM emissions. Increasing the EGR rate leads to deteriorating specific fuel consumption and power at lower speed and higher load. Also, the reduction rates of NOx emissions for hot and cooled EGR are similar.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.66-73
• /
• 2004

This paper presents characteristics of combustion and exhaust gas properties according to variation of the combustion chamber for economy and emissions standards. In order to use combustion and exhaust gas properties data, it is necessary to build some data base, which use cylinder pressure sensor and emission tester. A feasibility and necessity of combustion pressure based cylinder spark timing control has been examined. So, this was obtained the coefficient of variation(COV) and the specific fuel consumption(sfc). Using the results of the test, the effects of the variable combustion chamber can be improved combustion stability and be reduced exhaust emission.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.98-103
• /
• 2019

Integrity prediction of the operation equipment of naval vessels is essential to maintain the efficiency of the operation performance in urgent situations. Recently, the integrated condition assessment system(ICAS) was introduced and maintained to improve operational performance. This technology is related with ICAS, and it must be localized through extensive research. In this paper, we present the results of applying the data-driven model to the predictability methods of diesel generators, which are naval vessel operation equipment.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2563-2566
• /
• 2011

Government has presented a guideline for the calculation of carbon emission with infrastructures in 2011, which aims to manage the GHG(greenhouse gas) emission of construction sector. Generally, the main emission sources of construction works are divided into the fuel consumption of equipments and the use of materials. This study investigated the characteristics of GHG emission with the use of equipments under the construction of railroad track. Track types are classified into ballasted track and concrete track. As a result, the specific GHG emission on the construction of ballasted track at the A line was 39.53 ton $CO_{2e}/km$ and concrete track was 25.54 ton $CO_{2e}/km$. Ballasted track showed higher specific GHG emission than concrete track because of the additional construction works by the use of gravels. In future, it is necessary to study the comparison of GHG emissions with construction methods including the use of materials. Based on these results, the low carbon construction of railroad will be established continuously.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.29-39
• /
• 2010

The system performance of the regenerative gas-turbine cycle with the steam injection into the combustor has been studied through the thermodynamic cyclic analysis. The effects of the pressure ratio, the steam injection ratio, the ambient temperature, and the turbine inlet temperature are investigated on the thermal efficiency, the fuel consumption, and the specific power as well as the operating conditions for the maximum thermal efficiency of the system. The results of the present analysis find that the use of steam injection in the regenerative gas-turbine system can greatly enhance the thermal efficiency and the specific power of the system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.896-902
• /
• 2009

EGR is applied in order to lower temperature of combustion chamber by using the specific heat of carbon dioxide in engine exhaust gas. However, the problem of EGR system in diesel engine is high PM concentration. Combined EGR system can be reduced it by mixing exhaust gas of gas engine into the intake air of diesel engine. This experimental study was designed for EGR system for both engines use. The results of EGR experimental study by using diesel engine and gas engine are as follows. 1) The pressure of combustion and rate of heat release decreased. 2) The specific fuel consumption increased. But, up to middle load, it little increased. 3) NO concentration has decreased up to 50% in almost all combustion area. 4) The variation of the PM concentration at low load is not so seen. But at high load, PM increased rapidly when concentration of oxygen is decreased and most of it caused the increasing of Dry Soot.

• Journal of Navigation and Port Research
• /
• v.44 no.4
• /
• pp.283-290
• /
• 2020

BOG (Boil Off Gas) generation is unavoidable in the liquefied hydrogen carrier, and proper measures are necessary to prevent pressure problems inside the cargo tank. The BOG can be used as propulsion fuel for ships, and the remaining parts used for propulsion must be effectively managed, such as in the form of reliquefying or burning. This study proposes an BOG reliquefaction system optimized for a 160,000 m3 liquefied hydrogen carrier with a hydrogen propulsion system. The system comprises a hydrogen compression and helium refrigerant section, and increases the efficiency by effectively using the cold energy of the BOG discharged from the cargo tank. In this study, the system was evaluated through the exergy efficiency and SEC (Specific Energy Consumption) analysis according to the rate of the reliquefaction of the BOG while the hydrogen BOG with a supply temperature of -220℃ entered the reliquefaction system. As a result, it showed SEC of 4.11 kWh/kgLH2 and exergy efficiency of 60.1% at the rate of reliquefaction of 20%. And the parametric study of the effects of varying the hydrogen compression pressure, inlet temperature of the hydrogen expander, and the feed hydrogen temperature was conducted.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.4
• /
• pp.539-553
• /
• 2004

Up to the present time, many methods to estimate emissions from a particular diesel engines have wholly depended on the quantity of diesel fuel consumed. Then, the recommended emission factors were normalized by fuel consumption, and further total activity was estimated by the total fuel consumed. One of main purposes in the study is newly to develop emission factors for the railroad diesel rolling stock (RDRS) and to estimate a total amount of major gaseous pollutants from the RDRS in Korea. Prior to develop a Korean mode emission factor. the emission factor from the USEPA was simply applied for comparative studies. When applying the USEPA emission factors, total exhaust emissions from the RDRS in Korea were estimated by 28,117tons of NOx, 2,832.3tons of CO, and 1,237.5tons of HC, etc in 2001. In this study, a emission factor for the RDRS, so called the KoRail mode (the Korean Railroad mode) has been developed on the basis of analyzing the driving pattern of the Gyeongbu-Line especially for the line-haul mode. Explicitly to make the site specific emission factors, many uncertainty problems concerning weighting factors for each power mode, limited emission test, incomplete data for RDRS, and other important input parameters were extensively examined. Total exhaust emissions by KoRail mode in Korea were estimated by 10,960tons of NOx, and 4,622tons of CO, and so on in the year of 2001. The emissions estimated by the USEPA mode were 2.6 times higher for NOx, and 1.6 times lower for CO than those by the KoRail mode. As a conclusion, based on the emission calculated from both the USEPA mode and the KoRail mode, the RDRS is considered as one of the significant mobile sources for major gaseous pollutants and thus management plans an(1 control strategies for the RDRS must be established to improve air quality near future in Korea.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.60-72
• /
• 1981

This study was carried out to find out the effects of the sheaf size of paddy harvested by the binders on the threshing performance, load characteristics and power requirement of an auto-feed thresher. The results of the study are summarized as follows: 1. The seperating performance of the thresher appeared to be satisfactory for all the sheaf sizes although the amount of rubbishes and empty grains slightly increased with the sheaf size of paddy. 2. There was no significant difference in grain output quality of the thresher among the three sheaf sizes. However, the amount of grains left unthreshed increased with the sheaf size. In the case of the largest sheaf size with the feed rate of 780kg/h, it exceeded the limit set by the national inspection regulations. 3. The position of the feed-chain rail gave a significant effect on the power requirement of the thresher. At the feed rate of 780kg/h, the net power required to convey sheafs through the feed chain was in the range of 0.37 to 0.50 PS for the middle and lowest position of feed-chain rail, and there was no significant difference among the sheaf sizes. At the highest position, however, it appeared that the smallest sheaf required more power than the others. The net power requirements at this position were 1.03, 0.59. 0.65 PS for the smallest, medium and largest sheafs respectively. 4. The torques of both the thresher and the engine shaft increased with the feed rate and were not affected by the sheaf size for the lower two feed rates of 520 and 780kg/h. At the highest feed rate of 1,040 kg/h, however, they were affected by the sheaf size. In this case, the medium sheaf size gave lower values than the others. 5. The variations in the thresher and the engine torque increased with the feed rate and were not affected by the sheaf size for the feed rate of 520kg/h. At the feed rate of 780kg/h, however, they increased with sheaf size. And at the feed rate of 1,040 kg/h, the torque variations increased greatly for all the sheaf sizes due to an over-load operating condition. 6. It appeared that the average and maximum power requirements of the thresher increased with the feed rate. But, there was no significant difference in power requirement among the sheaf sizes for the lower two feed rates. 7. The threshing efficiency of the thresher was in the range of 214-249 kg/ps.h with the feed rates of 520 and 780 kg/h, and it was not affected by both the sheaf size and the feed rate. At the feed rate of 1,040 kg/h, however, it decreased to as low as 171-174 kg/ps.h because of a sudden increase in power requirement. 8. The average power requirements of the engine were slightly higher than those of the thresher due to the slippage of flat belt between the thresher and engine. It appeared that power transmission from the engine to the thresher was maintained properly since slippages were moderately low with the range of 2.78 to 6.51% throughout the tests. 9. The specific fuel consumption of the engine (diesel 8PS) decreased as the feed rate increased. However, there was no significant reduction in specific fuel consumption as the feed rate increased above 780 kg/h.