• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.121-122
• /
• 2016

Recently in the domestic construction industry, source depletion has resulted in instances of ready-mixed concrete companies using river sand or crushed sand with high fine particle content. But the use of such low-quality fine aggregate is known to cause concrete quality to decline and have negative effects. So this study analyzed how much of an impact changes in fine particle content have on cement mortar's engineering characteristics. As a result, the flow rate and air quantity, which are characteristics of unhardened mortar, were shown to decrease as fine particle content increased, and compression strength, a characteristic of light mortar, was shown to subtly increase as fine particle content decreased.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.87-91
• /
• 2001

The a-C:H films have been grown on the glass substrate by PECVD method, where plasma was generated with a 60 Hz line power source. The carbonization is checked from peak intensities of D($sp^3$) and G($sp^2$) peaks in Raman spectra and is analyzed using the Gaussian convolution method of spectrum. Both the bonding strength of C-H and the ratio of $sp^3$ to $sp^2$ in bonding are found to be slightly dependent of partial pressure of $C_2H_2$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.627-632
• /
• 2002

The paper considers acoustic analysis of the shock absorbing muffler within a rotary compressor. The internal space of the compressor is modelled as a combination of cavities and pipes. A simple one-dimensional impedance approach is used fur the acoustic analysis in the low frequency range, with ignoring the effects of gas flow and temperature gradients that are closely related to power efficiency of the compressor. Using the similarity between the vibration isolator and the shock absorbing muffler, the source strength transmissibility is newly proposed as a performance measure of the muffler and its validity is supported by power analysis. Some Important muffler design rules obtained are; (1) a muffler cavity and its opening throat should be used as a pair, (2) a long thin throat is desirable for high frequency noise isolation, (3) a large muffler cavity should be used with care since it shortens the working frequency range of the muffler. The rules were applied to redesign a compressor muffler currently in use, and a significant improvement was achieved by simply attaching a throat to the outlet holes of the muffler.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.1
• /
• pp.74-82
• /
• 2003

In this paper, an experimental program was undertaken to test the analysis on Component and mechanical characteristics for crushed stone of excavated Rocks from Sandstone, Shale, Mudstone, for use as a new source of aggregate. Physical and mechanical properties, required for aggregate materials, of major constituents of rock wastes including Sandstone, Shale, Mudstone, Felsite, Basalt, Marl were measured in the laboratory Test results showed that the Shale, Felsite, Basalt tested in this study might possibly be used for construction aggregates. In case of Sandstone and Mudstone, some physical properties such as rock strength were generally adoptable but the aggregate characteristics were lower than required.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.231-233
• /
• 2005

Laser have been utilized as a heat source for the soldering of electronic components for the their capability of localized heating and faster heating rate. Laser soldering process, especially the diode laser soldering of BGA solderball was investigated. In this study, an attempt was made to investigate the possibility of laser soldering using Sn-37Pb and Sn-3Ag-0.5Cu solderball. The laser energy absorbed on the pad raised the temperature of the solderball forming a reflowed solder bump. The result were discussed based on the measurement of pull and shear strength of the bond.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.54-61
• /
• 1984

Numerical calculation of the flow field past a passenger car was carried out by using a panel method with a small computer of 5Mbyte memory size. The shape of car body was simplified and reconstructed by 2180 panels on which a constant strength sink (or source) was distributed. The separation of flow from the surface and the wake flow were not considered in the calculation because of the computer memory limitation. All of the results of calculation were presented by using a 3-dimensional computer graphics. In spite of small memory size of computer, generally good agreements were obtained, except the separated region, from the comparison of pressure distribution between numerical analysis and wind tunnel experiment with 1/5 scaled model.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.4 no.2
• /
• pp.1-6
• /
• 2008

Very High Temperature Gas Cooled Reactor (VHTR) has been selected as a high energy heat source for nuclear hydrogen generation. The VHTR can produce hydrogen from heat and water by using a thermo-chemical process or from heat, water, and natural gas by steam reformer technology. A co-axial double-tube primary hot gas duct (HGD) is a key component connecting the reactor pressure vessel and the intermediate heat exchanger (IHX) for the VHTR. In this study, a preliminary design analysis for the primary HGD of the nuclear hydrogen system was carried out. These preliminary design activities include a determination of the size, a strength evaluation and an appropriate material selection. The determination of the size was undertaken based on various engineering concepts, such as a constant flow velocity model, a constant flow rate model, a constant hydraulic head model, and finally a heat balanced model.

• Laser Solutions
• /
• v.18 no.4
• /
• pp.6-11
• /
• 2015

Specially designed and 3D printed samples were prepared and joined by a diode laser source. To increase the strength of joining and reliability of samples, the surface was patterned by using a 3D printer. The joining surface was prepared as hemispherical shape with no-patterns, 0.5mm pitch, 0.75mm pitch and 1mm pitch. The optical properties of samples were measured by using an integrated sphere where classical Kubelka-Munk theory and modified Richard-Mudgetts theory for the analysis applied. Scanning speed was set at 500mm/min and laser power was varied between 9 and 10watts for the preliminary joining characteristic analysis.

• Journal of Welding and Joining
• /
• v.35 no.2
• /
• pp.30-34
• /
• 2017

The trend of the plasma cutting and laser cutting technology of metal alloys including high strength steel, aluminum alloys for the welding structures has been studied. The high-precision plasma systems offer a denser, higher energy arc that in effect produces a sharper cutting tool and high quality cutting products. The high-quality fiber laser systems with compact design and easy set-up make it ideal for cutting in the pipeline or steel structre manufacturing. This paper covers the scientometric analysis of the high efficient cutting technology which are based on the published research works in the 'plasma and laser', and 'cutting technology' obtained from Web of Science, and deals with the details of the background data of the plasma cutting and laser cutting technology.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.3
• /
• pp.231-241
• /
• 1997

A tracer model was applied in the Far East Asia to investigate the dry deposition rates of air pollutants on Korean Peninsula originated from different countries including China and Japan. Wind direction was chosen to predict the maximum deposition rates and SO$_2$ was chosen as a tracer to estimate the source strength. Model simulation shows that inflow, deposition and airborne ratios of China-originated SO$_2$ were 50%, 8% and 30%, respectively, at most. Also it was found that deposition, outbounded and airborne ratios of Korea-originated SO$_2$ were 15~77%, 8~75%, and 3~30%, respectively Model simulation also shows that inflow, deposition and airborne ratios of Kyushu-originated SO$_2$ were, 30~45%, 8~14％ and 20~25%, respectively. This study shows that tracer model can be applied on the estimation of air pollutants partitioning in regional scale and that more sophisticated modules and schemes can be developed and applied to better predict the transboundary amounts of air pollutants in this region.