• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.671-677
• /
• 2014

In this paper, a new basic unit is proposed. Then, a cascaded multilevel inverter basded on the series connection of n number of these new basic units is proposed. In order to generate all of the voltage levels (even and odd) at the output, three different algorithms to determine the magnitude of the dc voltage source are proposed. Reductions in the number of power switches, driver circuits and dc voltage sources in addition to increases in the numbr of output voltage levels are some of the advantages of the proposed cascaded multilevel inverter. These results are obtained through a comparison of the proposed inverter and its algorithms with an H-bridge cascaded multilevel inverter from the point of view of the number of power electronic devices. Finally, the capability of the proposed topology with its proposed algorithms in generating all of the voltage levels is verified through experimental results on a laboratorary prototype of a 49-level inverter.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.231-232
• /
• 2017

This paper describes the design and implementation of a 2.5kW (500V, 5A) simmer circuit that maintains the ionization of xenon gas inside the lamp. The design is based on a LCC resonant converter in continuous conduction mode (CCM) with above resonant frequency to take advantage of high power density from using parasitic elements such as the leakage inductance in a power transformer. In addition, since the converter has current source output characteristics, it is suitable for maintaining ionization of the lamp having the negative resistance load characteristic. To verify this converter design, PSpice modeling was performed. Finally, the developed simmer circuit is verified by a resistive load of rated performance and the Ionization maintenance operation of the xenon flash lamp.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.186-193
• /
• 2020

We investigate a fog-detection CCT control system using low deck lighting as a solution to the forward visibility of pole-type street lamps employed on existing roads. The lighting standards were met with a light source that has less compared with those of pole-type street lamps. The results show that the transmission rate was increased by changing the color temperature by automatically recognizing fog in bad weather and minimizing the phenomenon of lighting. In addition, it was allowed to create a safer and more comfortable driving environment for drivers owing to flicker or light pollution of existing pole-type street lamps. As a result, if lighting is used at a lower level than pole-type street lamps, the accident rate caused by securing the driver's forward visibility can be reduced sharply and existing problems can be resolved.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.133-138
• /
• 2021

We propose a Ku-band three-stack CMOS power amplifier to enhance the output power and efficiency. To minimize the dc power consumption, the driver stage is designed using common-source structure. To obtain high output power and utilize a voltage combining method, the power stage is designed using stack structure. To verify the proposed power amplifier structure, we design a Ku-band power amplifier using 65-nm RFCMOS process which provide nine metal layers. The P1dB, power-added efficiency, and gain are higher than 20 dBm, 23 dB, and 25%, respectively, while the operating frequency is 14 GHz-16 GHz.

• International Journal of Computer Science & Network Security
• /
• v.23 no.3
• /
• pp.169-176
• /
• 2023

The vehicular ad hoc network (VANET) is currently an important approach to improve personal safety and driving comfort. ANEL is a MAC-based authentication scheme that offers all the advantages of MAC-based authentication schemes and overcomes all their limitations at the same time. In addition, the given scheme, ANEL, can achieve the security objectives such as authentication, privacy preservation, non-repudiation, etc. In addition, our scheme provides effective bio-password login, system key update, bio-password update, and other security services. Additionally, in the proposed scheme, the Trusted Authority (TA) can disclose the source driver and vehicle of each malicious message. The heavy traffic congestion increases the number of messages transmitted, some of which need to be secretly transmitted between vehicles. Therefore, ANEL requires lightweight mechanisms to overcome security challenges. To ensure security in our ANEL scheme we can use cryptographic techniques such as elliptic curve technique, session key technique, shared key technique and message authentication code technique. This article proposes a new efficient and light authentication scheme (ANEL) which consists in the protection of texts transmitted between vehicles in order not to allow a third party to know the context of the information. A detail of the mapping from text passing to elliptic curve cryptography (ECC) to the inverse mapping operation is covered in detail. Finally, an example of application of the proposed steps with an illustration

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.378-390
• /
• 2023

The SPES (Selective Production of Exotic Species) facility, currently under development at Legnaro National Laboratories of INFN, aims at the production of intense RIB (Radioactive Ion Beams) employing the Isotope Separation On-Line (ISOL) technique for interdisciplinary research. The radioactive isotopes of interest are produced by the interaction of a multi-foil uranium carbide target with a 40 MeV 200 μA proton beam generated by a cyclotron proton driver. The Target Ion Source (TIS) is the core of the SPES project, here the radioactive nuclei, mainly neutron-rich isotopes, are stopped, extracted, ionized, separated, accelerated and delivered to specific experimental areas. Due to efficiency reasons, the TIS unit needs to be replaced periodically during operation. In this highly radioactive environment, the employment of autonomous systems allows the manipulation, transport, and storage of the TIS unit without the need for human intervention. A dedicated remote handling infrastructure is therefore under development to fulfill the functional and safety requirement of the project. This contribution describes the layout of the SPES target area, where all the remote handling systems operate to grant the smooth operation of the facility avoiding personnel exposure to a high dose rate or contamination issues.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.87-97
• /
• 2016

This work proposes a time-shared 10b DAC based on a two-step resistor string to minimize the effective area of a DAC channel for driving each AMOLED display column. The proposed DAC shows a lower effective DAC area per unit column driver and a faster conversion speed than the conventional DACs by employing a time-shared DEMUX and a ROM-based two-step decoder of 6b and 4b in the first and second resistor string. In the second-stage 4b floating resistor string, a simple current source rather than a unity-gain buffer decreases the loading effect and chip area of a DAC channel and eliminates offset mismatch between channels caused by buffer amplifiers. The proposed 1-to-24 DEMUX enables a single DAC channel to drive 24 columns sequentially with a single-phase clock and a 5b binary counter. A 0.9pF sampling capacitor and a small-sized source follower in the input stage of each column-driving buffer amplifier decrease the effect due to channel charge injection and improve the output settling accuracy of the buffer amplifier while using the top-plate sampling scheme in the proposed DAC. The proposed DAC in a $0.18{\mu}m$ CMOS shows a signal settling time of 62.5ns during code transitions from '$000_{16}$' to '$3FF_{16}$'. The prototype DAC occupies a unit channel area of $0.058mm^2$ and an effective unit channel area of $0.002mm^2$ while consuming 6.08mW with analog and digital power supplies of 3.3V and 1.8V, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.186-186
• /
• 2000

After LeComber et al. reported the first amorphous hydrogenated silicon (a-Si: H) TFT, many laboratories started the development of an active matrix LCDs using a-Si:H TFTs formed on glass substrate. With increasing the display area and pixel density of TFT-LCD, however, high mobility TFTs are required for pixel driver of TF-LCD in order to shorten the charging time of the pixel electrodes. The most important of these drawbacks is a-Si's electron mobiliy, which is the speed at which electrons can move through each transistor. The problem of low carier mobility for the a-Si:H TFTs can be overcome by introducing polycrystalline silicon (poly-Si) thin film instead of a-Si:H as a semiconductor layer of TFTs. Therefore, poly-Si has gained increasing interest and has been investigated by many researchers. Recnetly, fabrication of such poly-Si TFT-LCD panels with VGA pixel size and monolithic drivers has been reported, . Especially, fabricating poly-Si TFTs at a temperature mach lower than the strain point of glass is needed in order to have high mobility TFTs on large-size glass substrate, and the monolithic drivers will reduce the cost of TFT-LCDs. The conventional methods to fabricate poly-Si films are low pressure chemical vapor deposition (LPCVD0 as well as solid phase crystallization (SPC), pulsed rapid thermal annealing(PRTA), and eximer laser annealing (ELA). However, these methods have some disadvantages such as high deposition temperature over $600^{\circ}C$, small grain size (<50nm), poor crystallinity, and high grain boundary states. Therefore the low temperature and large area processes using a cheap glass substrate are impossible because of high temperature process. In this study, therefore, we have deposited poly-Si thin films on si(100) and glass substrates at growth temperature of below 40$0^{\circ}C$ using newly developed high rate magnetron sputtering method. To improve the sputtering yield and the growth rate, a high power (10~30 W/cm2) sputtering source with unbalanced magnetron and Si ion extraction grid was designed and constructed based on the results of computer simulation. The maximum deposition rate could be reached to be 0.35$\mu$m/min due to a high ion bombardment. This is 5 times higher than that of conventional sputtering method, and the sputtering yield was also increased up to 80%. The best film was obtained on Si(100) using Si ion extraction grid under 9.0$\times$10-3Torr of working pressure and 11 W/cm2 of the target power density. The electron mobility of the poly-si film grown on Si(100) at 40$0^{\circ}C$ with ion extraction grid shows 96 cm2/V sec. During sputtering, moreover, the characteristics of si source were also analyzed with in situ Langmuir probe method and optical emission spectroscopy.

• Journal of Distribution Science
• /
• v.15 no.2
• /
• pp.79-90
• /
• 2017

Purpose - Cargo Distribution O2O Business Model is the form of business that connects the cargo and empty cargo-truck based on mobile online platform. In Korean cargo distribution market, FIN(Freight Information Network) is the only model that represents O2O Business Model. The purpose of this paper is investigating the recognition of driver who is the only source of income toward cargo distribution O2O Business Model, and based on the investigated recognition of trucker, suggesting strategic implication. Research design, data, and methodology - PESTLE methodology which is massive environment analysis, and 5 Forces Model when analyze the present and future of cargo distribution O2O business market of industrial structure analysis were used as investigation methodology. Also structured questionnaire was used for trucker's recognition investigation. Based on collected 196 structured effective questionnaires organized with 26 questions were analyzed using statistics package. Results - 51.3% of responded driver is non-differentiated, deprofessionalize form that transport all types of cargo. 95.4% recognize cargo distribution O2O Business Model, FIN is needed, especially during back-hall(94.7%). As a payment method, monthly due is preferred(73%), but it is also needed to pay annual due and pay whenever cargo and cargo-truck are connected(24.5%). Trucker prefer FIN operation corporation which has rich supply(85.2%), and is liberal in supply in any domestic area(75.5%). Conclusions - First, 91% was the member of FIN, and 95% of non-member recognized FIN is needed. 83% of them has the intent to be the member of FIN. Second, besides of monthly due as payment method of FIN, 25% has positive recognition toward new payment method. The new payment method means paying annual due and pay whenever cargo and cargo-truck are connected. Third, because of information imbalance about the cargo and cargo-truck among, operators whose business goal is FIN, it was investigated that transportation fee is low and commission charge of broker is high. The core of Korean Cargo Distribution O2O Business Model, FIN, is online platform that matches cargo and cargo-truck. Therefore, FIN operator should minimize the amount of single transportation of trucker. This study suggests the development of shipper using FIN, diversify distribution channel, suggesting backhaul toward trucker as solution to FIN operator.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.185-201
• /
• 2018

Road lighting is highly preferred as the major nighttime road safety countermeasures. When it comes to the pole-type road lighting, as it's installed at a certain height from the road surface, the driver is dazzled by the light source, interrupting the driver's visibility and furthermore, the light leaks to the area outside the road boundary, worsening the energy efficiency as well as generating the light pollution to the surrounding environment including the animals and plants. The study developed the low-level lighting systems, so it is possible to prevent the lights from being strayed, so there is no any side effects in terms of the sleep deprivation. The study compared the performance as the lightings between low-level lightings and conventional pole based lighting systems. As the results, the low-level lighting systems showed the higher performance in terms of average surface luminance, uniformity, glare compared to the conventional lighting systems.