• Bulletin of the Korean Chemical Society
• /
• 제28권8호
• /
• pp.1375-1382
• /
• 2007

A column preconcentration method with pulverized Amberlite XAD-4 loaded with bismuthiol I (BI) has been developed for the determination of trace Cd(II) and Cu(II) in various real samples by flame atomic absorption spectrophotometry. Various experimental conditions, such as the size of XAD-4, adsorption flow rate, amount of bismuthiol I, stirring time for adsorbing bismuthiol I on XAD-4, pH of sample solution, amount of XAD-4- BI, desorption solvent, and desorption flow rate, were optimized. Also, the adsorption capacity and the adsorption rate of Cd(II) and Cu(II) on XAD-4-BI were investigated. The interfering effects of various concomitant ions were investigated, Bi(III), Sn(II) and Fe(III) were found to affect the determination. But the interference by these ions was completely eliminated by adjusting the amount of XAD-4-BI resin to 0.70 g, although the adsorption flow rate was slower. For Cd(II) our proposed technique obtained a dynamic range of 0.5-40 ng mL-1, a correlation coefficient (R2) of 0.9913, and a detection limit of 0.3 ng mL-1. For Cu(II), the corresponding values were 2.0-120 ng mL-1, 0.9921 and 1.02 ng mL-1. To validate this proposed technique, the aqueous samples (stream water, reservoir water, tap water and wastewater), the diluted brass sample and the plastic sample, as real samples, were used. Recovery yields of 91-103% were obtained. These measured data were not different from ICP-MS data at 95% confidence level. Our proposed method was also validated using rice flour CRM (normal, fortified) samples. From the results of our experiment, we found that the technique we present here can be applied to the determination of Cd(II) and Cu(II) in various real samples.

• Bulletin of the Korean Chemical Society
• /
• 제34권11호
• /
• pp.3307-3311
• /
• 2013

A new fiber optical sensor was developed for the determination of 2,4-dichlorophenol (DCP). The sensor was based on DCP oxidation by oxygen with the catalysis of iron(III) tetrasulfophthalocyanine (Fe(III)PcTs). The optical oxygen sensing film with $Ru(bpy)_3Cl_2$ as the fluorescence indicator was used to determine the consumption of oxygen in solution. A lock-in amplifier was used for detecting the lifetime of the oxygen sensing film by measuring the phase delay change of the sensor head. The different variables affecting the sensor performance were evaluated and optimized. Under the optimal conditions (i.e. pH 6.0, $25^{\circ}C$, Fe(III)PcTs concentration of 0.62 mg/mL), the linear detection range and response time of the sensor are $1.0{\times}10^{-6}-9.0{\times}10^{-6}$ mol/L and 250 s, respectively. The sensor displays high selectivity, good repeatability and stability, and can be used as an effective tool in analyzing DCP concentration in practical samples.

• Bulletin of the Korean Chemical Society
• /
• 제29권5호
• /
• pp.1038-1042
• /
• 2008

Mono and multilayer TiO2(Fe, $PEG_{600}$) films were deposited by the dip-coating on $SiO_2$/glass substrate using sol-gel method. In an attempt to improve the antibacterial properties of doped $TiO_2$ films, the influence of the iron oxides and polyethilenglycol ($PEG_{600}$) on the morphological, optical, surface chemical composition and biological properties of nanostructured layers was studied. Complementary measurements were performed including Spectroscopic Ellipsometry (SE), Scanning Electron Microscopy (SEM) coupled with the fractal analysis, X-Ray Photoelectron Spectroscopy (XPS) and antibacterial tests. It was found that different concentrations of Fe and $PEG_{600}$ added to coating solution strongly influence the porosity and morphology at nanometric scale related to fractal behaviour and the elemental and chemical states of the surfaces as well. The thermal treatment under oxidative atmosphere leads to films densification and oxides phase stabilization. The antibacterial activity of coatings against Escherichia Coli bacteria was examined by specific antibacterial tests.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.577-582
• /
• 2007

A variational formulation for plane elasticity problems is derived based on an isogeometric approach. The isogeometric analysis is an emerging methodology such that the basis functions in analysis domain arc generated directly from NURBS (Non-Uniform Rational B-Splines) geometry. Thus. the solution space can be represented in terms of the same functions to represent the geometry. The coefficients of basis functions or the control variables play the role of degrees-of-freedom. Furthermore, due to h-. p-, and k-refinement schemes, the high order geometric features can be described exactly and easily without tedious re-meshing process. The isogeometric sensitivity analysis method enables us to analyze arbitrarily shaped structures without re-meshing. Also, it provides a precise construction method of finite element model to exactly represent geometry using B-spline base functions in CAD geometric modeling. To obtain precise shape sensitivity, the normal and curvature of boundary should be taken into account in the shape sensitivity expressions. However, in conventional finite element methods, the normal information is inaccurate and the curvature is generally missing due to the use of linear interpolation functions. A continuum-based adjoint sensitivity analysis method using the isogeometric approach is derived for the plane elasticity problems. The conventional shape optimization using the finite element method has some difficulties in the parameterization of boundary. In isogeometric analysis, however, the geometric properties arc already embedded in the B-spline shape functions and control points. The perturbation of control points in isogeometric analysis automatically results in shape changes. Using the conventional finite clement method, the inter-element continuity of the design space is not guaranteed so that the normal vector and curvature arc not accurate enough. On tile other hand, in isogeometric analysis, these values arc continuous over the whole design space so that accurate shape sensitivity can be obtained. Through numerical examples, the developed isogeometric sensitivity analysis method is verified to show excellent agreement with finite difference sensitivity.

• Macromolecular Research
• /
• 제17권2호
• /
• pp.128-132
• /
• 2009

Fucoidan, a sulfated polysaccharide derived from brown seaweed, is an important material valued for its various biological functions, including anti-coagulation, anti-aging, and immune system support. In this study, we examined the potential of fucoidan as a novel emulsifying agent in BSA (bovine serum albumin)-stabilized emulsion at a neutral pH. We measured the dispersed oil-droplet size, surface zeta-potential and creaming formation of 0.5 wt% BSA emulsion (20 wt% oil traction) in the absence and presence of fucoidan. The average particle size and zeta-potential value were 625.4 nm and -30.91 mV in only BSA-stabilized emulsion and 745.2 nm and -44.2 mV in 1.0 wt% fucoidan-added BSA emulsion, respectively. This result suggested that some positive charges of the BSA molecules interacted with the negative charges of fucoidan to inhibit the flocculation among the oil droplets. The creaming rate calculated from the backscattering data measured by Turbiscan dramatically decreased in 1.0 wt% fucoidan-added BSA emulsion during storage. Accordingly, the repulsion forces induced among the oil particles coated with 1.0 wt% fucoidan in emulsion solution resulted in significantly increased emulsion stability. The turbidity of the BSA-stabilized emulsion at 500 nm decreased during five days of storage. However, the fucoidan-added BSA emulsion exhibited a higher value of turbidity than the BSA-stabilized emulsion did. In conclusion, an anionic sulfated fucoidan lowered the surface zeta-potential of BSA-coated oil droplets via the electrostatic interaction, and subsequently inhibited the flocculation among the oil droplets, thereby clearly minimizing the creaming and phase separation of the emulsion.

• 한국물환경학회지
• /
• 제22권1호
• /
• pp.116-121
• /
• 2006

Fundamental investigations have been carried out to find the applicability of manganese nodule as an adsorbent of nickel ion with an intention that nickel can be secured in manganese nodule along with the treatment of wastewater. The average content of manganese in nodules which used in the experiments was about 27%. The content of nickel in manganese nodules was observed to increase up to 4 times higher with comparison to its original value after adsorption. When the initial concentration of nickel ion in artificial wastewater was lower than 500 mg/L, its adsorbed amount on manganese nodule was shown to increase continuously. However, no more than about 82 mg/L of nickel was attained at higher initial nickel ion concentration than 500 mg/L. The adsorption of nickel ion was increased with temperature under experimental conditions and as the size of manganese nodule particles became smaller more nickel ion was adsorbed on adsorbent. Regarding the effect of pH, the adsorption of nickel ion was more hindered as the solution became acidic. Adsorption behavior of nickel ion on manganese nodule was found to follow the Freundlich model well and kinetic analysis showed that the adsorption reaction of nickel ion was second order. Thermodynamic parameters for the nickel ion adsorption were estimated on the basis of thermodynamic equations and they were in good agreement with experimental results.

• 한국식품조리과학회지
• /
• 제22권6호통권96호
• /
• pp.905-913
• /
• 2006

The properties of water soluble powder of propolis(WSP), made with different levels(0, 20, 40, 60, 80%) of ethanol extract of propolis(EEP) and hydrocolloid were investigated, along with the quality changes of its bread after 7 days' of storage at $30^{\circ}C$ The yield of WSP containing 40% EEP treated at $160^{\circ}C$ was the highest at 59.3% and the brown color of all the powders tended to be darkened with increasing EEP content. The turbidity of WSP treated at higher temperature was decreased in its aqueous solution (10%, w/w), and this was considered to be due to the presence of minute nonsoluble particles. Antioxidative activities determined by DPPH(1,1-diphenyl-2-picrylhydrazyl) were the lowest in WSP treated at $140^{\circ}C$, while those of the WSP samples prepared at 160 and $180^{\circ}C$ were as high as that of WSP containing more than 40% EEP, regardless of EEP concentration. The propolis breads with added WSP made at $160^{\circ}C$ were selected as the most desirable powder for subsequent study. Bread with WSP40 was the heaviest while the volume loss of WSP80 was the greast after baking. The moisture contents of the propolis bread were drastically decreased until 3 days' of storage, but it was thought that WSP might be ineffective for the prevention of moisture loss. The pH of breads without EEP was decreased after 3 days' of storage, while that of the WSP breads remained almost unchanged until 5 days' of storage. Total bacterial counts also exhibited decay levels during the storage. In conclusion, water soluble powder of propolis is useful as a natural antioxidative and antibacterial material in various types of food.

• 미생물학회지
• /
• 제36권2호
• /
• pp.97-102
• /
• 2000

녹장균(Metarhizium ansiopliae)을 생물살충제로서 활용할 목적으로 녹강균의 균사생육 및 포자형성에 미치는 환경요인과 균사외 분비 효소 활성에 대하여 조사였다. M. anisopliae DGUM35001의 균사 생장을 보여주었으며, 공중균사는 SDPY 사용시 가장 우수하엿다. 최소배지로 Czapek-Dox 한천배지를 사용하여 탄소원 이용성 실험의 결과, 단당류에서 glucoserk 이당류에서 sucrose가 가장 우수한 탄소원이었다. 고분자 물질로 chitin 사용시 우수한 균사 생육을 보여주었다. 유기질소원으로 bacto-peptone과 soytone아 무기질소원으로 urea와 ammonium phosphate가 우수한 균사생육을 나타내었으며, 아미노산으로 serine 첨가시 가장 우수한 균사 생육을 나타내었다. Starch배지를 사용하였을 때 가장 우수한 포자형성의 결과를 얻었다. 액체배양후 군사를 제거한 상등액을 조효소액으로 사용시 analyase와 prorease 효소 활성이 우수하였다. 그러나,;ipase와 chitinase 효소활동은 상대적으로 낮았다.

• Journal of Pharmaceutical Investigation
• /
• 제37권1호
• /
• pp.7-13
• /
• 2007

To produce stable polymer coating layer using the interaction between metal stent and polymer layer, Ahx-HSAB was synthesized by coupling 6-aminoheanoic acid (Ahx) with N-Hydroxy succinimidyl 4-azidobenzonate (HSAB) containing photo reactive group. Then, Ahx-HSAB was applied to self·assembled monolayer (SAM) on $TiO_2$-coated surface, since one end of Ahx-HSAB was carboxyl acid which was known to be able to interact with $TiO_2$ surface. That SAM layer was incubated in 1% polycaprolacton (PCL) solution and photoreacted by ultraviolet light (254 nm) to produce the chemical bond between SAM and polymer layer, followed by PCL polymer coating ({\sim}5\;{\mu}m$) by the method of spray coating. The surface change was investigated by measuring of contact angle of the surface. The contact angle values of stainless steel (SS) surface, $TiO_2$-coated surface, SAM layer by Ahx-HSAB, photoreacted surface with PCL and PCL layer by spray coating were 70.48${\pm}$1.89, 38.57${\pm}$3.31, 60.14${\pm}$2.21, 54.91${\pm}$2.70 and 56.47${\pm}$2.12, respectively. The stability of polymer layers was tested by incubation of PCL-coated plates in 0.1M PBS buffer (pH 7.4, 0.05%, Tween 80) with vigorous shaking (200 rpm). While the poiymer layer prepared by these processes showed the intact surface morphology over 3 days, the polymer layers prepared by spray coating of PCL onto SS plate (control 1) and $TiO_2$-coated SS plate (control 2) were Peeled off in 3 days. Thus, the polymer coating method using SAM and photoreaction seems to be a effective method to obtain the stable polymer layer onto SS surface.

• 한국농공학회논문집
• /
• 제57권1호
• /
• pp.111-118
• /
• 2015

This research aims to utilize lapilli from the Mt. Baekdusan as environmently-friendly construction material. First of all, the neutralizing method for fabricating lapilli-cement-mixed bioblock was examined. And then, by use of the neuralized bioblock with microorganism for water purification, the growth inhibition effect against the pathogenic coliform bacillus was evaluated. The result regarding growth inhibition effect on pathogenic coliform bacillus indicates that the pretreatment condition, which is a concurrent procession with aqueous solution of 10% di-ammonium Phosphate after water curing, led to pH degraded below 10 which was the target value. Therefore it was concluded that the method was effective on bio-block neutralization. The microorganisms purifying water and di-ammonium phosphate were detected through the examination for microorganism existence on the bioblock, therefore it was concluded that the bioblock composed of lapilli and cement is able to be utilized in various structures as an environment friendly construction material.