• Journal of the Korean institute of surface engineering
• /
• v.41 no.1
• /
• pp.28-32
• /
• 2008

In this paper CdS thin films, which were widely used window layer of the CdS/CdTe and the CdS/$CuInSe_2$ heterojunction solar cell, were grown by chemical bath deposition, which is a very attractive method for low-cost and large-area solar cells, and the structural, optical and electrical properties of the films was studied. As the thiourea/$CdAc_2$ mole ratio was increased, the deposition rate of CdS films prepared by CBD was increased due to increasing reaction velocity in solution and the optical bandgap was increased at higher thiourea/$CdAc_2$ mole ratio due to larger grain size and continuous microstructure. The minimum resistivity of the films was at thiourea/$CdAc_2$ mole ratio of 3.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.531-534
• /
• 2002

NiO buffer layers for YBCO coated conductors were deposited on hi-axially textured Ni substrates by MOCVD(metal organic chemical vapor deposition) method, using single solution source. To establish the processing condition, oxygen partial pressure and deposition temperature were changed. The surface orientation and degree of texture were estimated by X-ray diffraction, X-ray pole figure and atomic force microscopy. The FWHMs of in-plane and out-of-plane of the NiO films were about 10$^{\circ}$. The surface roughness was a function of deposition temperature. The AFM surface roughness of NiO films is in the range of 3∼10 nm, when NiO films was grown at 450∼530$^{\circ}C$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.521-524
• /
• 2005

ZnO 2-D nanowall structure with around 100 nm thickness, which is composed of tens of nm scale ZnO single crystals, was fabricated through the low temperature chemical solution growth method. Electro Chemical Deposition (ECD) technique was applied to attach the ZnO seed crystals on ITO coated glass substrate. The ZnO nanowall structure was grown in the 0.015 mol$\%$ of aqueous solution of zinc nitrate and hexamethenamine at 60$^{\circ}C$ for 20 - 40 h. The nanowall structure depends on the ECD condition or the applied voltage and duration time. The nanowall shows a photoluminescence around 550 - 700 nm spectrum range.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.452-452
• /
• 2013

ZnO is one of the most attractive transparent conductive oxide (TCO) films because of low toxicity, a wide band gap material and relatively low cost. However, the electrical conductivity of un-doped ZnO is too high to use it as TCO films in practical application. To improve electrical properties of undoped ZnO, transition metal (TM) doped ZnO films such as Al doped ZnO or Ti doped ZnO have been extensively studied. Here, we prepared Ti doped ZnO thin films by atomic layer deposition (ALD) for the application of TCO films. ALD was used to prepare Ti-doped ZnO thin films due to its inherent merits such as large area uniformity, precise composition control in multicomponent thin films, and digital thickness controllability. Also, we demonstrated that ALD method can be utilized for fabricating highly ordered freestanding nanostructures of Ti-doped ZnO thin films by combining with BCP templates, which can potentially used in the photovoltaic applications.

• Journal of Chest Surgery
• /
• v.37 no.4
• /
• pp.307-312
• /
• 2004

With the development of cardiac surgical technique, we need more prosthetic materials for repairing the intra- and extracardiac defects. Although bovine pericardial bioprosthesis treated with glutaraldehyde (GA) solution is one of the most popular materials, it has a drawback of later calcific degeneration. The purpose of this study is to investigate the effectiveness of several materials and methods in reducing the calcific degeneration of bovine pericardium. Material and Method: Forty square-shaped pieces of bovine pericardia were fixed in 0.625% GA solution with 4 g/L MgCl$_2$ㆍ6$H_2O$ as a control group (group 1). Other 40 pieces pre-treated with 1 % SDS(group 2) and 40 pieces post-treated with 8% glutamate (group 3) and 2% chitosan (group 4) were also fixed in the same GA solution. Other 40 pieces pre-treated with 1% SDS and post-treated with 8% glutamate and 40 pieces post-treated with 2% chitosan were also fixed in the same GA solution (group 5, 6). The pericardial pieces were implanted into the belly of 40 Fisher 344 rats subdermally and were extracted 1 month, 2 months, 3 months, and 6 months after the implantation. With an atomic absorption spectrophotometry, we measured the calcium amount deposited and examined the tissue with microscope. Result: The calcium deposition in 1 month was less in group 2, 5, 6 than that in group 1 (p＜0.05). It was most prominent in group 5 (p＜0.01). This finding continued in 2 month. In 3 month, the calcium deposition was less in group 3 and 4 as well as group 2, 5, and 6 than in group 1. In 6 month, the calcium deposition in group 2, 3, 4, 5, and 6 was less than that in group 1 and the difference was more than that of 1, 2, and 6 month. The microscopic calcium deposition was also less in group 2 and 5. Calcium deposition developed in the whole layer of pericardium, beginning with the surrounding the collagen fiber and progressing inwardly. Conclusion: Pre-treatment with SDS, post-treatment with glutamate or chitosan, and SDS pre-treatment and post-treatment with glutamate or chitosan were effective in reducing the calcium deposition in bovine pericardium. Moreover, the combined method of SDS pre-treatment and glutamate post-treatment was more effective than other methods.

• Journal of Powder Materials
• /
• v.14 no.4
• /
• pp.238-244
• /
• 2007

The electrophoretic deposition process of Ni nano-particles in organic suspension was employed for self-repairing of heat exchanger tubes. For this purpose, Ni nano-particles prepared by levitational gas condensation method were dispersed into the solution of ethanol with the addition of dispersant Hypermer KD2. For electrophoretic deposition of Ni nano-particles on the Ni alloy specimen, constant electric fields of 20 and 100 V $cm^{-1}$ were applied to the specimen in Ni-dispersed solution. It was found that as electrophoretic deposition proceeds, the size of the pit or crack remarkably decreased due to the agglomeration of Ni nano-particles at the pit or crack. This strongly suggests that the electrophoretic mobility of the charged particles is larger for the damaged part with a higher current value rather than outer surfaces with a lower current value.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2431-2437
• /
• 2014

In this study, Ni, Ni-Cu and Ni/Cu catalysts were deposited onto C-fiber textiles via the electrophoretic deposition method, and the growth characteristics of carbon nanofibers on the deposited catalyst/C-fiber textiles were investigated. The catalyst deposition onto C-fiber textiles was accomplished by immersing the C-fiber textiles into Ni or Ni-Cu mixed solutions, producing the substrate by post-deposition of Ni onto C-fiber textiles with pre-deposited Cu, and passing it through a gas mixture of $N_2$, $H_2$ and $C_2H_4$ at $700^{\circ}C$ to synthesize carbon nanofibers. For analysis of the characteristics of the synthesized carbon nanofibers and the deposition pattern of catalysts, SEM, EDS, BET, XRD, Raman and XPS analysis were conducted. It was found that the amount of catalyst deposited and the ratio of Ni deposition in the Ni-Cu mixed solution increased with an increasing voltage for electrophoretic deposition. In the case of post-deposition of Ni catalyst onto substrates with pre-deposited Cu, both bimetallic catalyst and carbon nanofibers with a high level of crystallizability were produced. Carbon nanofibers yielded with the catalyst prepared in Ni and Ni-Cu mixed solutions showed a Y-shaped morphology.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.252.2-252.2
• /
• 2013

ZnO nanostructures have a lot of interest for decades due to its varied applications such as light-emitting devices, power generators, solar cells, and sensing devices etc. To get the high performance of these devices, the factors of nanostructure geometry, spacing, and alignment are important. So, Patterning of vertically- aligned ZnO nanowires are currently attractive. However, many of ZnO nanowire or nanorod fabrication methods are needs high temperature, such vapor phase transport process, metal-organic chemical vapor deposition (MOCVD), metal-organic vapor phase epitaxy, thermal evaporation, pulse laser deposition and thermal chemical vapor deposition. While hydrothermal process has great advantages-low temperature (less than $100^{\circ}C$), simple steps, short time consuming, without catalyst, and relatively ease to control than as mentioned various methods. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using of nanosphere template with various precursor concentration and components via hydrothermal process. The brief experimental scheme is as follow. First synthesized ZnO seed solution was spun coated on to cleaned Si substrate, and then annealed $350^{\circ}C$ for 1h in the furnace. Second, 200nm sized close-packed nanospheres were formed on the seed layer-coated substrate by using of gas-liquid-solid interfacial self-assembly method and drying in vaccum desicator for about a day to enhance the adhesion between seed layer and nanospheres. After that, zinc oxide nanowires were synthesized using a low temperature hydrothermal method based on alkali solution. The specimens were immersed upside down in the autoclave bath to prevent some precipitates which formed and covered on the surface. The hydrothermal conditions such as growth temperature, growth time, solution concentration, and additives are variously performed to optimize the morphologies of nanowire. To characterize the crystal structure of seed layer and nanowires, morphology, and optical properties, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and photoluminescence (PL) studies were investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.93-93
• /
• 2013

In recent years, multifunctional ternary nitride thin films have received extenstive attention due to its versatility in many applications. In particular, noble metal based ternary nitride thin films showed a promising properties in the application of Multifunctional heating resistor films because its good electrical properties and excellent resistance against oxidation and corrosion. In this study, we prepared multifunctional noble metal based ternary nitride thin films by atomic layer deposition (ALD) and plasma-enhanced ALD (PEALD) method. ALD and PEALD techniques were used due to their inherent merits such as a precise composition control and large area uniformity, which is very attractive for preparing multicomponent thin films on large area substrate. Here, we will demonstrate the design concept of multifunctional noble metal based ternary thin films. And, the relationship between microstructural evolution and electrical resistivity in noble metal based ternary thin films will be systemically presented. The useful properties of noble metal based ternary thin films including anti-corrosion and anti-oxidation will be discussed in terms of hybrid functionality.